NXP Semiconductor designed the LPC2400 microcontrollers around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded Trace. The LPC2400 microcontrollers have 512 kB of on-chip high-speedFlash memory. This Flash memory includes a special 128-bit wide memory interface andaccelerator architecture that enables the CPU to execute sequential instructions fromFlash memory at the maximum 72 MHz system clock rate. This feature is available onlyon the LPC2000 ARM Microcontroller family of products. The LPC2400 can execute both32-bit ARM and 16-bit Thumb instructions. Support for the two Instruction Sets meansEngineers can choose to optimize their application for either performance or code size atthe sub-routine level. When the core executes instructions in Thumb state it can reducecode size by more than 30 % with only a small loss in performance while executinginstructions in ARM state maximizes core performance.
上传时间： 2013-11-15
上传用户：zouxinwang
PROTEUS VSM在单片机系统仿真中的应用:：介绍了单片机系统仿真工具PROTEUS VSM 及其在单片机系统仿真中的应用，给出了具体的应用实例，详细地介绍了PROTEUS VSM 与Keil uVision3的接口方法。关键词：单片机；Keil uVision3；仿真；外围器件；PROTEUS VSM； Abstract：This paper introduces the simulation tool for M CU system —PROTEUS VSM ， and presents the application ofPROTEUS VSM in MCU system simulation through an applicable example．The way of interfacing PROTEUS VSM to Keil uVision3is also presented in details．Keywords：MCU ；Keil uVision3；simulation；peripheral devices；PROTEUS VSM ；
上传时间： 2013-11-16
上传用户：chenxichenyue
Using the XGATE for Manchester DecodingTable of Contents 1 Introduction 1.1 XGATE Module in S12X 2 Decoding Algorithm 3 Software Implementation 3.1 Frame Scheme 3.2 Operating Modes and Demo 3.3 Files Summary 3.4 Complete Mode Flowchart 4 Manchester Encoder 4.1 Devices Used 5 Conclusion Appendix A Noise Elements During RF Transmissions in the Manchester Decoding ImplementationA.1 Types of Noise A.2 Effects of Noise A.3 Workaround for Noise Effects
标签： Manchester XGATE 译码
上传时间： 2013-10-15
上传用户：wqq123456
The PCA82C250 and PCA82C251 are advanced transceiver products for use in automotive and general industrialapplications with transfer rates up to 1 Mbit/s. They support the differential bus signal representation beingdescribed in the international standard for in-vehicle CAN high-speed applications (ISO 11898). Controller AreaNetwork (CAN) is a serial bus protocol being primarily intended for transmission of control related data between anumber of bus nodes.
上传时间： 2013-11-24
上传用户：Alick
The PCA9541 is a 2-to-1 I2C-bus master selector designed for high reliability dual masterI2C-bus applications where system operation is required, even when one master fails orthe controller card is removed for maintenance. The two masters (for example, primaryand back-up) are located on separate I2C-buses that connect to the same downstreamI2C-bus slave devices. I2C-bus commands are sent by either I2C-bus master and are usedto select one master at a time. Either master at any time can gain control of the slavedevices if the other master is disabled or removed from the system. The failed master isisolated from the system and will not affect communication between the on-line masterand the slave devices on the downstream I2C-bus.
上传时间： 2013-10-09
上传用户：3294322651
Designing Boards with Atmel AT89C51, AT89C52, AT89C1051, and AT89C2051 for Writing Flash at In-Circuit Test:Recent improvements in chips andtesters have made it possible for thetester to begin taking over the role traditionallyassigned to the PROM programmer.Instead of having a PROM programmerwrite nonvolatile memoriesbefore assembling the board, the in-circuittester writes them during in-circuittesting operations. Many Teradyne Z18-series testers are now in use loadingcode into nonvolatile memories, microcontrollersand in-circuit programmable logic devices. The purpose of this note is to explain how the Z18 approaches the writing task for Atmel AT89C series IC’s,so that designers of boards using these chips can get the best results.
标签： Designing Boards Atmel with
上传时间： 2013-11-20
上传用户：lijianyu172
Abstract: This application note explains the hardware of different types of 1-Wire® interfaces and software examples adapted to this hardware with a focus on serial ports. Depending on the types of iButtons required for a project and the type of computer to be used, the most economical interface is easily found. The hardware examples shown are basically two different types: 5V general interface and 12V RS-232 interface. Within the 5V group a common printed circuit board could be used for all circuits described. The variations can be achieved by different populations of components. The same principal is used for the 12V RS-232 interface. The population determines if it is a Read all or a Read/Write all type of interface. There are other possible circuit implementations to create a 1-Wire interface. The circuits described in this application note cover many different configurations. For a custom application, one of the described options can be adapted to meet individual needs.
标签： iButtons Reading Writing and
上传时间： 2013-10-29
上传用户：long14578
The MC68HC05K0 is a low cost, low pin countsingle chip microcomputer with 504 bytes of userROM and 32 bytes of RAM. The MC68HC05K0 isa member of the 68HC05K series of devices whichare available in 16-pin DIL or SOIC packages.It uses the same CPU as the other devices in the68HC05 family and has the same instructions andregisters. Additionally, the device has a 15-stagemulti-function timer and 10 general purposebi-directional I/0 lines. A mask option is availablefor software programmable pull-downs on all ofthe I/O pins and four of the pins are capable ofgenerating interrupts.The device is ideally suited for remote-controlkeyboard applications because the pull-downs andthe interrupt drivers on the port pins allowkeyboards to be built without any externalcomponents except the keys themselves. There isno need for external pull-up or pull-down resistors,or diodes for wired-OR interrupts, as these featuresare already designed into the device.
上传时间： 2014-01-24
上传用户：zl5712176
CAN与RS232转换节点的设计与实现 介绍将CAN总线接口与RS232总线接口相互转换的设计方法和2种总线电平转换关系，实现CAN总线与各模块的接口设计，制定了相应的软硬件设计方案，并给出软件设计流程图以及部分硬件设计原理图。为CAN总线与RS232总线互联提供了一种方法，对CAN总线与RS232总线接口设备的互联和广泛应用的实现具有重要意义。关键词：CAN总线；RS-232总线；串行通信Design and Realization of CAN and RS232 Transformation NodeZHOU Wei, CHENG Xiao-hong(Information Institute, Wuhan University of Technology, Wuhan 430070)【Abstract】This paper introduces one design method of the CAN bus interface and the RS232 bus interface interconversion, emphasizes two kindof bus level transformation relations, realizes the CAN bus and various modules connection design, formulates the design proposal of correspondingsoftware and hardware, and gives the flow chart of software design as well as the partial schematic diagram of hardware design. It providesonemethod for the CAN bus and the RS232 bus interconnection, has the vital significance to widespread application realization of the CAN busand theRS232 bus interface equipment interconnection.【Key words】CAN bus; RS-232 bus; serial communication
上传时间： 2013-11-04
上传用户：leesuper
This overview guide describes all the peripherals available for TMS320x28xx and TMS320x28xxx devices.Section 2 shows the peripherals used by each device. Section 3 provides descriptions of the peripherals.You can download the peripheral guide by clicking on the literature number, which is linked to the portable document format (pdf) file.
上传时间： 2013-11-21
上传用户：HGH77P99
