keil 使用笔记:在Memory窗口上输入address_type:address才能看到正确地址的变量debug～perfermance analyzer加入要察看的模块名称，然后view～perfermance analyzer window 可以察看各个模块运行时间①Display address_type:address B:Bit address C:Code Memory Bx:Code Bank D D：80H 命令可以查看特殊寄存器 data D I：0 命令可以查看内部RAM数据iData； D X：0 命令可以查看外部RAM数据xData； ②R1 //显示R1 register ~R1 //显示变量R1 R1 = R7 //对寄存器Rx操作R1 = --R7 R1 = 0x20 ③main //显示main()的开始地址d main //显示main()的代码④向RAM.ROM中写数据Enter data_type address_type:address expr,expr.... data_type:int char double float long E char data:0x20 1,2,3,4 //向data区0x20开始的地址写1,2,3,4 变量放在RAM的30H，要把定义放在main前面!另外特别注意，内部RAM通常供C程序存放中间变量等，所以一定要看看编译后的程序中是否存在存储单元冲突的情况，比如如果程序中 使用了别的寄存器组的话，08-1FH单元就不能用了unsigned long data i _at_ 0x30
上传时间： 2013-11-05
上传用户：dongqiangqiang
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, and 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, and 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, and anappropriate action (e.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.
上传时间： 2013-10-23
上传用户：copu
TKS仿真器B系列快速入门
上传时间： 2013-10-31
上传用户：aix008
创新、效能、卓越是ADI公司的文化支柱。作为业界公认的全球领先数据转换和信号调理技术领先者，我们除了提供成千上万种产品以外，还开发了全面的设计工具，以便客户在整个设计阶段都能轻松快捷地评估电路。
上传时间： 2013-11-25
上传用户：kachleen
创新、效能、卓越是ADI公司的文化支柱。作为业界公认的全球领先数据转换和信号调理技术领先者，我们除了提供成千上万种产品以外，还开发了全面的设计工具，以便客户在整个设计阶段都能轻松快捷地评估电路。
上传时间： 2013-10-18
上传用户：cxl274287265
一个简单好用的B+树算法实现
上传时间： 2015-01-04
上传用户：缥缈
一个用Basic实现的B-Tree算法
上传时间： 2013-12-30
上传用户：ccclll
一个用Java applet实现的B-Tree算法
上传时间： 2013-12-25
上传用户：qiao8960
用C++实现的B-Tree算法
上传时间： 2014-01-20
上传用户：jiahao131
用Borland C写的B-Tree算法
上传时间： 2014-12-05
上传用户：xzt
