This example demonstrates the use of the ADC BLOCK and PWM BLOCKs. The generated DSP code produces the pulse waveform whose duty cycle is changing as the voltage applied to ADC input changes. The waveform period is kept constant.
标签： demonstrates the generated produces
上传时间： 2016-05-17
上传用户：sjyy1001
uc/os II 在80X86上的移值,源码.BLOCK部分
上传时间： 2013-11-25
上传用户：edisonfather
用MATLAB里的XILINX BLOCK, 支持FPGA算法, 实现开平方, 并且取整.当计算停止时, VALID为高电瓶.
上传时间： 2013-12-07
上传用户：xlcky
用MATLAB里的XILINX BLOCKS编写, 做嵌入式用的2个BLOCKS, 一个为除法BLOCK, 另一个为乘方BLOCK.
标签： BLOCKS BLOCK MATLAB XILINX
上传时间： 2016-06-19
上传用户：yimoney
intel thread building BLOCK 并行计算库的参考手册
标签： building thread intel BLOCK
上传时间： 2016-07-08
上传用户：xuanjie
Space Time of BLOCK Code Simulation
标签： Simulation Space BLOCK Code
上传时间： 2014-01-17
上传用户：zyt
presentation of Fast Variable BLOCK Size Motion Estimation Algorithms Based on Merge and Split Procedures for H.264/MPEG-4 AVC
标签： presentation Algorithms Estimation Variable
上传时间： 2014-01-12
上传用户：朗朗乾坤
Program main BIOS image | | /B - Program Boot BLOCK | | /N - Program NVRAM | | /C - Destroy CMOS checksum | | /E - Program Embedded Controller BLOCK | | /K - Program all non-critical BLOCKs | | /Kn - Program n th non-critical BLOCK only(n=0-7) | | /Q - Silent execution | | /REBOOT - Reboot after programming | | /X - Don t Check ROM ID | | /S - Display current system s ROMID | | /Ln - Load CMOS defaults
标签： Program Destroy BLOCK NVRAM
上传时间： 2016-07-26
上传用户：wfl_yy
挖雷游戏.1.运行效果与程序发布 2.主类Game 3.方块 BLOCK 4.雷区 MineSquare 5.雷标数目 FindAroundMineMarkNumber 6.雷标判DetermineMineMarkIsRightOrWrong 7.成片挖开区域 DetermineDigArea 8.无雷连通区 FindSafeArea 9.随机布雷 RandomSetMine 10.周围地雷个数FindAroundMineNumber 11.显示剩余雷数CountMine 12.计时器TimeCount
标签： FindAroundMineMarkNumber MineSquare BLOCK Deter
上传时间： 2013-12-27
上传用户：caozhizhi
D169 Demo - DMA0 Repeated Burst to-from RAM, Software Trigger Description A 32 byte BLOCK from 220h-240h is transfered to 240h-260h using DMA0 in a burst BLOCK using software DMAREQ trigger. After each transfer, source, destination and DMA size are reset to inital software setting because DMA transfer mode 5 is used. P1.0 is toggled durring DMA transfer only for demonstration purposes. ** RAM location 0x220 - 0x260 used - always make sure no compiler conflict ** ACLK= n/a, MCLK= SMCLK= default DCO ~ 800k
标签： Description Repeated Software to-from
上传时间： 2014-01-09
上传用户：thinode
