该论文介绍了D类音频功放，Class D Audio Power Amplifier，全英文，可以借鉴学习。
标签： 功放制作
上传时间： 2013-06-04
上传用户：英雄
微弱信号检测装置 四川理工学院 刘鹏飞、梁天德、曾学明 摘要： 本设计以TI的Launch Pad为核心板，采用锁相放大技术设计并制作了一套微弱信号检测装置，用以检测在强噪声背景下已知频率微弱正弦波信号的幅度值，并在液晶屏上数字显示出所测信号相应的幅度值。实验结果显示其抗干扰能力强，测量精度高。 关键词：强噪声；微弱信号；锁相放大；Launch Pad Abstract: This design is based on the Launch Pad of TI core board, using a lock-in Amplifier technique designed and produced a weak signal detection device, to measure the known frequency sine wave signal amplitude values of the weak in the high noise background, and shows the measured signal amplitude of the corresponding value in the liquid crystal screen. Test results showed that it has high accuracy and strong anti-jamming capability. Keywords: weak signal detection; lock-in-Amplifier; Launch Pad 1、引言 随着现代科学技术的发展，在科研与生产过程中人们越来越需要从复杂高强度的噪声中检测出有用的微弱信号，因此对微弱信号的检测成为当前科研的热点。微弱信号并不意味着信号幅度小，而是指被噪声淹没的信号，“微弱”也仅是相对于噪声而言的。只有在有效抑制噪声的条件下有选择的放大微弱信号的幅度，才能提取出有用信号。微弱信号检测技术的应用相当广泛，在生物医学、光学、电学、材料科学等相关领域显得愈发重要。 2、方案论证 针对微弱信号的检测的方法有很多，比如滤波法、取样积分器、锁相放大器等。下面就针对这几种方法做一简要说明。 方案一：滤波法。 在大部分的检测仪器中都要用到滤波方法对模拟信号进行一定的处理，例如隔离直流分量，改善信号波形，防止离散化时的波形混叠，克服噪声的不利影响，提高信噪比等。常用的噪声滤波器有：带通、带阻、高通、低通等。但是滤波方法检测信号不能用于信号频谱与噪声频谱重叠的情况，有其局限性。虽然可以对滤波器的通频带进行调节，但其噪声抑制能力有限，同时其准确性与稳定性将大打折扣。
上传时间： 2013-11-04
上传用户：lty6899826
Abstract: Alexander Graham Bell patented twisted pair wires in 1881. We still use them today because they work so well. In addition we have the advantage ofincredible computer power within our world. Circuit simulators and filter design programs are available for little or no cost. We combine the twisted pair and lowpassfilters to produce spectacular rejection of radio frequency interference (RFI) and electromagnetic interference (EMI). We also illustrate use of a precision resistorarray to produce a customizable differential Amplifier. The precision resistors set the gain and common mode rejection ratios, while we choose the frequencyresponse.
上传时间： 2014-11-26
上传用户：Vici
Abstract: The MAX9930–MAX9933 family of RF controllers and detector can be used in a wide variety of applications. Anideal application is cable television (CATV) over fiber, where either a RF controller or a RF detector controls the gain of atransimpedance Amplifier (TIA). This application note shows how the MAX9930 (RF controller) can be used as either theRF controller or detector.
上传时间： 2013-10-11
上传用户：Pzj
Abstract: Build a composite Amplifier featuring high gain, wide bandwidth, good DC accuracy and low distortion
上传时间： 2014-12-23
上传用户：JasonC
The LT®6552 is a specialized dual-differencing 75MHzoperational Amplifier ideal for rejecting common modenoise as a video line receiver. The input pairs are designedto operate with equal but opposite large-signal differencesand provide exceptional high frequency commonmode rejection (CMRR of 65dB at 10MHz), therebyforming an extremely versatile gain block structure thatminimizes component count in most situations. The dualinput pairs are free to take on independent common modelevels, while the two voltage differentials are summedinternally to form a net input signal.
上传时间： 2014-12-23
上传用户：13691535575
Who has never experienced oscillations issues when using an operational Amplifier? Opampsare often used in a simple voltage follower configuration. However, this is not the bestconfiguration in terms of capacitive loading and potential risk of oscillations.Capacitive loads have a big impact on the stability of operational Amplifier-basedapplications. Several compensation methods exist to stabilize a standard op-amp. Thisapplication note describes the most common ones, which can be used in most cases.The general theory of each compensation method is explained, and based on this, specific
上传时间： 2013-10-28
上传用户：chenbhdt
This application note is an overview discussion of theLinear Technology SPICE macromodel library. It assumeslittle if any prior knowledge of this software library or itshistory. However, it does assume familiarity with both theanalog simulation program SPICE (or one of its manyderivatives), and modern day op amps, including bipolar,JFET, and MOSFET Amplifier technologies
上传时间： 2013-11-14
上传用户：zhanditian
设计了水声信号发生系统中的功率放大电路，可将前级电路产生的方波信号转换为正弦信号，同时进行滤波、功率放大，使其满足换能器对输入信号的要求。该电路以单片机AT89C52，集成6阶巴特沃思低通滤波芯片MF6以及大功率运算放大器LM12为核心，通过标准RS232接口与PC进行通信，实现信号增益的程控调节，对干扰信号具有良好的抑制作用。经调试该电路工作稳定正常，输出波形无失真，在输出功率以及放大增益、波纹系数等方面均满足设计要求。 This paper presented a design and implementation of underwater acoustic power amplifer. This circuit converted the rectangle signal generated by frontend circuit into the sine signal， then filtered and power amplification， it meets the requirements of the transducer.Included AT89C52， 6th order Butterworth filter MF6， hipower amplififier LM12.Communication with PC through the RS232 port. The signal gain is adjustable and could be remote controlled. It has a good inhibitory effect on the interference signal. After debugged， this circuit works stable， the output waveform has no distortion， it meets the design requirement in outprt power， Amplifier gain and ripple factor.
上传时间： 2013-11-20
上传用户：qwe1234
OPTOELECTRONICS CIRCUIT COLLECTION AVALANCHE PHOTODIODE BIAS SUPPLY 1Provides an output voltage of 0V to +80V for reverse biasingan avalanche photodiode to control its gain. This circuit canalso be reconfigured to supply a 0V to –80V output.LINEAR TEC DRIVER–1This is a bridge-tied load (BTL) linear Amplifier for drivinga thermoelectric cooler (TEC). It operates on a single +5Vsupply and can drive ±2A into a common TEC.LINEAR TEC DRIVER–2This is very similar to DRIVER–1 but its power output stagewas modified to operate from a single +3.3V supply in orderto increase its efficiency. Driving this Amplifier from astandard +2.5V referenced signal causes the output transistorsto have unequal power dissipation.LINEAR TEC DRIVER–3This BTL TEC driver power output stage achieves very highefficiency by swinging very close to its supply rails, ±2.5V.This driver can also drive ±2A into a common TEC. Operationis shown with the power output stage operating on±1.5V supplies. Under these conditions, this linear Amplifiercan achieve very high efficiency. Application ReportThe following collection of analog circuits may be useful in electro-optics applications such as optical networkingsystems. This page summarizes their salient characteristics.
上传时间： 2013-10-27
上传用户：落花无痕
