单片机I/O口的使用:对单片机的控制，其实就是对I/O口的控制，无论单片机对外界进行何种控制，亦或接受外部的控制，都是通过I/O口进行的。单片机总共有P0、P1、P2、P3四个8位双向输入输出端口，每个端口都有锁存器、输出驱动器和输入缓冲器。4个I/O端口都能作输入输出口用，其中P0和P2通常用于对外部存储器的访问。§4.1 MCS-51单片机的并行端口结构与操作 51系列单片机有4个I/O端口，每个端口都是8位准双向口，共占32根引脚。每个端口都包括一个锁存器(即专用寄存器P0～P3)、一个输出驱动器和输入缓冲器。通常把4个端口笼统地表示为P0～P3。
标签： 单片机
上传时间： 2013-11-06
上传用户：zhouxuepeng1
The PCA9555 is a 24-pin CMOS device that provides 16 bits of General Purpose parallelInput/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed toenhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvementsinclude higher drive capability, 5 V I/O tolerance, lower supply current, individual I/Oconfiguration, and smaller packaging. I/O expanders provide a simple solution whenadditional I/O is needed for ACPI power switches, sensors, push buttons, LEDs, fans, etc.The PCA9555 consists of two 8-bit Configuration (Input or Output selection); Input, Outputand Polarity Inversion (active HIGH or active LOW operation) registers. The systemmaster can enable the I/Os as either inputs or outputs by writing to the I/O configurationbits. The data for each Input or Output is kept in the corresponding Input or Outputregister. The polarity of the read register can be inverted with the Polarity Inversionregister. All registers can be read by the system master. Although pin-to-pin and I2C-busaddress compatible with the PCF8575, software changes are required due to theenhancements, and are discussed in Application Note AN469.
上传时间： 2013-11-13
上传用户：fredguo
The PCA9557 is a silicon CMOS circuit which provides parallel input/output expansion for SMBus and I2C-bus applications. The PCA9557 consists of an 8-bit input port register, 8-bit output port register, and an I2C-bus/SMBus interface. It has low current consumption and a high-impedance open-drain output pin, IO0. The system master can enable the PCA9557’s I/O as either input or output by writing to the configuration register. The system master can also invert the PCA9557 inputs by writing to the active HIGH polarity inversion register. Finally, the system master can reset the PCA9557 in the event of a time-out by asserting a LOW in the reset input. The power-on reset puts the registers in their default state and initializes the I2C-bus/SMBus state machine. The RESET pin causes the same reset/initialization to occur without de-powering the part.
上传时间： 2014-01-18
上传用户：bs2005
基于 I2C 总线的GPIO 扩展器件为主控器提供了额外的I/O 口，本文介绍了扩展器件的应用场合和选型指南，为设计者在设计中提供了参考。
上传时间： 2013-11-11
上传用户：llwap
The Philips family of Multiplexers and Switches consists of bi-directional translating switches controlled via the I2C or SMBus to fan out an upstream SCL/SDA pair to 2, 4 or 8 downstream channels of SCx/SDx pairs. The Multiplexers allow only one downstream channel to be selected at a time, while the Switches allow any individual downstream channel or combination of downstream channels to be selected, depending on the content of the programmable control register. Once one or several channels have been selected, the device acts as a wire, allowing the master on the upstream channel to send commands to devices on all the active downstream channels, and devices on the active downstream channels to communicate with each other and the master. External pull-up resistors are used to pull each individual channel up to the desired voltage level. Combined interrupt output and hardware reset input are device options that are featured.
上传时间： 2013-10-11
上传用户：dianxin61
The CAT9555 is a CMOS device that provides 16-bitparallel input/output port expansion for I²C and SMBuscompatible applications. These I/O expanders providea simple solution in applications where additional I/Osare needed: sensors, power switches, LEDs,pushbuttons, and fans.
上传时间： 2014-01-09
上传用户：1101055045
数字I/O脚有专用和复用。数字I/O脚的功能通过9个16位控制寄存器来控制。控制寄存器分为两类：（1）I/O复用控制寄存器（MCRX)，来选择I/O脚是外设功能还是I/O功能。（2）数据方向控制寄存器（PXDATDIR)：控制双向I/O脚的数据和数据方向。注意：数字I/O脚是通过映射在数据空间的控制寄存器来控制的，与器件的I/O空间无任何关系。240X/240XA多达41只数字I/O脚，多数具有复用功能。
标签： 数字
上传时间： 2013-10-31
上传用户：qimingxing130
I2C interface, is a very powerful tool for system designers. Theintegrated protocols allow systems to be completely software defined.Software development time of different products can be reduced byassembling a library of reusable software modules. In addition, themultimaster capability allows rapid testing and alignment ofend-products via external connections to an assembly-line computer.The mask programmable 87LPC76X and its EPROM version, the87LPC76X, can operate as a master or a slave device on the I2Csmall area network. In addition to the efficient interface to thededicated function ICs in the I2C family, the on-board interfacefacilities I/O and RAM expansion, access to EEPROM andprocessor-to-processor communications.
标签： microcontro Using 76X LPC
上传时间： 2013-12-30
上传用户：Artemis
The MC68HC05K0 is a low cost, low pin countsingle chip microcomputer with 504 bytes of userROM and 32 bytes of RAM. The MC68HC05K0 isa member of the 68HC05K series of devices whichare available in 16-pin DIL or SOIC packages.It uses the same CPU as the other devices in the68HC05 family and has the same instructions andregisters. Additionally, the device has a 15-stagemulti-function timer and 10 general purposebi-directional I/0 lines. A mask option is availablefor software programmable pull-downs on all ofthe I/O pins and four of the pins are capable ofgenerating interrupts.The device is ideally suited for remote-controlkeyboard applications because the pull-downs andthe interrupt drivers on the port pins allowkeyboards to be built without any externalcomponents except the keys themselves. There isno need for external pull-up or pull-down resistors,or diodes for wired-OR interrupts, as these featuresare already designed into the device.
上传时间： 2014-01-24
上传用户：zl5712176
基于多点网络的水厂自动监控系统设计Design of MPI Based Automatic Monitoring and Control System in Water Works刘 美 俊(湖南工程学院，湘潭411101)摘要针对水厂工作水泵多、现场离控制站距离远的特点，提出了一种基于MPI多点网络的自动监控系统的设计方法，分析了系统的工作原理，介绍了系统中数据的采集与处理、主站与从站的通信原理以及系统软件的设计。由于这种系统的主、从站PLC之间采用MPI网络通信，具有运行可靠、性能价格比高的特点，所以适用于中小规模水厂的分布式监控场合。关键词多点网络主站从站监控系统Abstract Ina ccordancew ithth efe atuersof w aterw orks,i. e. ，manyp umpsin o perationa ndth ep umps， farfor mt hec ontrolst ation,th em ethodo fdesigninga na utomati(〕monitoringa ndc ontorlsy stemb asedo nM PIis p resented.Th eo perationalpr incipleo fth esy stemi san alyzed,th ed atac olection,data processing; communication between master station and slave station as wel as design and system software are discussed. Because MPI network communicationis used among master station, slave stations and PLC, the system is reliable and high cost-efective. It is， suitable for smal and mediumsized water works for distrbuted monitoring and control.Keywords MPI Masterst ation Slaves tation Monitoringa ndc ontorlsy stem 自来 水 厂 的自动控制系统一般分为两大部分，一对组态硬件要求较高，投资较大。相对而言，MPI网是水源地深水泵的工作控制，一是水厂区变频恒压供络速度可达187.5 M bps，通过一级中继器传输距离可水控制，两部分的实际距离通常都比较远。某厂水源达Ikm 。根据水厂的具体情况，确定以MPI方式组地有3台深井泵给水厂区的蓄水池供水。水厂区的成网络，主站PLC为S7-300系列的CPU3121FM，从任务是对水池的水进行消毒处理后，通过加压泵向管站为S7-200系列的CPU222。这样既满足了系统要路恒压供水。选用Siemens公司的S7系列可编程控求，又相对于Profibus网络节省了三分之一的成本，制器(PLC)和上位机组成实时数据采集和监控系统， 这种分布式监控系统具有较高的性能价格比。系统对深水泵进行远程控制，对供水泵采用变频器进行恒中PLC的物理层采用RS - 485接口，网络延伸选用压控制以保证整个水厂的电机设备安全、可靠地运带防雷保护的中继器，使系统的安全运行得到了保行。证。MPI网络的拓扑结构如图1所示。1 多点网络(NWI)监控系统的组成Sie me ns 公司S7系列PLC通常有MP」多点网络与Profibus现场总线网络两种组网方式。Profibus现场总线的应用目前较为普遍，通用性较好，它由Profibus一DP, Profibus一FMS, Profibus一PA组成。Profibus - DP型用于分散外设间的数据传输，传输速率为9.6kbps一12Mbps，主要用于现场控制器与分散1/0之间的通信，可满足交直流调速系统快速响应的时间要求，特别适合于加工自动化领域的应用;Profibus - FMS主要解决车间级通信问题，完成中等传输速度的循环或非循环数据交换任务，适用于纺织、楼宇自动化、可编程控制器、低压开关等;Profibus - PA型采用了OSI模型的物理层和数据链路层，适用于过程自动化的总线类型。
上传时间： 2013-10-09
上传用户：fac1003
