ABSTRACT: This document explains how the Cupertino (MAXREFDES5#) subsystem reference design meets the higher resolution, higher voltage,and isolation needs of industrial control and industrial automation applications. Hardware and firmware design files as well as FFTs andhistograms from lab measurements are provided.
上传时间： 2013-10-20
上传用户：mnacyf
微弱信号检测装置 四川理工学院 刘鹏飞、梁天德、曾学明 摘要： 本设计以TI的Launch Pad为核心板，采用锁相放大技术设计并制作了一套微弱信号检测装置，用以检测在强噪声背景下已知频率微弱正弦波信号的幅度值，并在液晶屏上数字显示出所测信号相应的幅度值。实验结果显示其抗干扰能力强，测量精度高。 关键词：强噪声；微弱信号；锁相放大；Launch Pad ABSTRACT: This design is based on the Launch Pad of TI core board, using a lock-in amplifier technique designed and produced a weak signal detection device, to measure the known frequency sine wave signal amplitude values of the weak in the high noise background, and shows the measured signal amplitude of the corresponding value in the liquid crystal screen. Test results showed that it has high accuracy and strong anti-jamming capability. Keywords: weak signal detection; lock-in-amplifier; Launch Pad 1、引言 随着现代科学技术的发展，在科研与生产过程中人们越来越需要从复杂高强度的噪声中检测出有用的微弱信号，因此对微弱信号的检测成为当前科研的热点。微弱信号并不意味着信号幅度小，而是指被噪声淹没的信号，“微弱”也仅是相对于噪声而言的。只有在有效抑制噪声的条件下有选择的放大微弱信号的幅度，才能提取出有用信号。微弱信号检测技术的应用相当广泛，在生物医学、光学、电学、材料科学等相关领域显得愈发重要。 2、方案论证 针对微弱信号的检测的方法有很多，比如滤波法、取样积分器、锁相放大器等。下面就针对这几种方法做一简要说明。 方案一：滤波法。 在大部分的检测仪器中都要用到滤波方法对模拟信号进行一定的处理，例如隔离直流分量，改善信号波形，防止离散化时的波形混叠，克服噪声的不利影响，提高信噪比等。常用的噪声滤波器有：带通、带阻、高通、低通等。但是滤波方法检测信号不能用于信号频谱与噪声频谱重叠的情况，有其局限性。虽然可以对滤波器的通频带进行调节，但其噪声抑制能力有限，同时其准确性与稳定性将大打折扣。
上传时间： 2013-11-04
上传用户：lty6899826
ABSTRACT: Many digital devices incorporate analog circuits. For instance, microprocessors, applicationspecificintegrated circuits (ASICs), and field-programmable gate arrays (FPGAs) may have internalvoltage references, analog-to-digital converters (ADCs) or digital-to-analog converters (DACs). However,there are challenges when you integrate more analog onto a digital design. As with all things in life, inelectronics we must always trade one parameter for another, with the application dictating the propertrade-off of analog function. In this application note, we examine how the demand for economy of spaceand cost pushes analog circuits onto digital substrates, and what design challenges emerge.
上传时间： 2013-11-16
上传用户：菁菁聆听
ABSTRACT: This application note describes a new generation of digital-input Class D audio amplifiers that achieve high PSRRperformance, comparable to traditional analog Class D amplifiers. More importantly, these digital-input Class D amplifiersprovide additional benefits of reduced power, complexity, noise, and system cost.
上传时间： 2013-12-20
上传用户：JIUSHICHEN
ABSTRACT: This application note describes the essential workings of an electrocardiogram (ECG). It discussesfactors that disrupt the ECG signals and make reliable, highly-accurate electrical characterization difficult. Theindustry-standard solution for ECG electrical characterization, which uses an analog front-end and ADCcombination, is explained. The article then introduces the MAX11040 simultaneous-sampling, sigma-deltaADC as a compelling, highly integrated solution that eliminates the need for the AFE, and saves both spaceand cost for the application.
上传时间： 2013-12-23
上传用户：sssl
ABSTRACT: This tutorial discusses proper printed-circuit board (PCB) grounding for mixed-signal designs. Formost applications a simple method without cuts in the ground plane allows for successful PCB layouts withthis kind of IC. We begin this document with the basics: where the current flows. Later, we describe how toplace components and route signal traces to minimize problems with crosstalk. Finally, we move on toconsider power supply-currents and end by discussing how to extend what we have learned to circuits withmultiple mixed-signal ICs.
上传时间： 2013-11-04
上传用户：pol123
ABSTRACT: This application note describes how to design boost converters using the MAX17597 peakcurrent-mode controller. Boost converters can be operated in discontinuous conduction mode (DCM) orcontinuous conduction mode (CCM). This operating mode can affect the component choices, stress levelin power devices, and controller design. Formulas for calculating component values and ratingsare alsopresented.
上传时间： 2013-11-15
上传用户：zcs023047
ABSTRACT: This application note describes how sampling clock jitter (time interval error or "TIE jitter") affectsthe performance of delta-sigma digital-to-analog converters (DACs). New insights explain the importanceof separately specifying low-frequency (< 2x passband frequency) and high-frequency or wideband (> 2xpassband frequency) jitter tolerance in these devices. The article also provides an application example ofa simple highly jittered cycle-skipped sampling clock and describes a method for generating a properbroadband jittered clock. The document then goes on to compare Maxim's audio DAC jitter tolerance tocompetitor audio DACs. Maxim's exceptionally high jitter tolerance allows very simple and low-cost sampleclock implementations.
上传时间： 2013-10-25
上传用户：banyou
ABSTRACT: A digital RF modulator, an integrated solution that satisfies stringent DOCSIS RF-performancerequirements, takes advantage of modern technologies like high-performance wideband digital-to-analogconversion and CMOS technology scaling. This application note describes the concept and advantages ofa digital quadrature amplitude modulation (QAM) modulator that uses the direct-RF architecture to enablea cable access platform (CCAP) system.
上传时间： 2013-10-20
上传用户：drink！
ABSTRACT: Quartz crystals are mechanical resonators with piezoelectric properties. The piezoelectricproperties (electric potential across the crystal is proportional to mechanical deformation) allow their use
标签： 晶体振荡器
上传时间： 2013-10-17
上传用户：时代将军
