oRTP is a LGPL licensed C library implementing the RTP protocol (rfc1889). It is available for most unix clones (primilarly Linux and HP-UX), and Microsoft Windows.
标签： implementing available licensed protocol
上传时间： 2014-02-07
上传用户：lx9076
sql for setup the system. this is not that important.
标签： important system setup that
上传时间： 2013-12-26
上传用户：2525775
This project is created using the Keil ARM CA Compiler. The Logic Analyzer built into the simulator may be used to monitor and display any variable or peripheral I/O register. It is already configured to show the PWM output signal on PORT3.0 and PORT3.1 This ARM Example may be debugged using only the uVision Simulator and your PC--no additional hardware or evaluation boards are required. The Simulator provides cycle-accurate simulation of all on-chip peripherals of the ADuC7000 device series. You may create various input signals like digital pulses, sine waves, sawtooth waves, and square waves using signal functions which you write in C. Signal functions run in the background in the simulator within timing constraints you configure. In this example, several signal functions are defined in the included Startup_SIM.INI file.
标签： the Analyzer Compiler project
上传时间： 2013-12-19
上传用户：Yukiseop
This ZIP file contains the support files for programming the Infineon C167CR CAN interface. Refer to Application Note 115a for details of this example code.
标签： programming the interface Infineon
上传时间： 2013-12-11
上传用户：2404
This ZIP file contains the support files for programming the Infineon C167CR CAN interface. Refer to Application Note 115a for details of this example code. this is part 2
标签： programming the interface Infineon
上传时间： 2014-12-03
上传用户：lixinxiang
This example demonstrates how to erase, write, and read the on-chip 640-byte EEPROM Data Memory of the Analog Devices ADuC812, ADuC814, ADuC816, and ADuC824 devivces. This example includes a µ Vision2 Project with a target for each supported device.
标签： demonstrates example on-chip EEPROM
上传时间： 2015-05-04
上传用户：wl9454
This example project shows how to use the Idle Power-Saving Mode of the 8051Fx.
标签： Power-Saving the example project
上传时间： 2015-05-04
上传用户：weixiao99
This example program shows how to configure and use the A/D Converter of the following microcontroller: STMicroelectronics ST10F166 After configuring the A/D, the program reads the A/D result and outputs the converted value using the serial port. To run this program... Build the project (Project Menu, Build Target) Start the debugger (Debug Menu, Start/Stop Debug Session) View the Serial Window (View Menu, Serial Window #1) View the A/D converter peripheral (Peripheral Menu, A/D Converter) Run the program (Debug Menu, Go) A debug script (debug.ini) creates buttons that set different analog values in A/D channels. As the program runs, you will see the A/D input and output change. Other buttons create signals that generate sine wave or sawtooth patterns as analog inputs. µ Vision3 users may enable the built-in Logic Analyzer to view, measure and compare these input signals graphically.
标签： microcontroll Converter configure following
上传时间： 2014-12-01
上传用户：独孤求源
How to Use Tables With the JTable (in the API reference documentation) class you can display tables of data, optionally allowing the user to edit the data. JTable doesn t contain or cache data it s simply a view of your data. Here s a picture of a typical table displayed within a scroll pane
标签： documentation the reference display
上传时间： 2013-12-23
上传用户：ayfeixiao
SelectionDemo also has code (not included in the preceding snippet) that changes the table s selection orientation. By changing a couple of boolean values, you can make the table allow either column selections or individual cell selections, instead of row selections.
标签： SelectionDemo the preceding included
上传时间： 2015-05-04
上传用户：gut1234567
