Designers of signal receiver systems often need to performcascaded chain analysis of system performancefrom the antenna all the way to the ADC. Noise is a criticalparameter in the chain analysis because it limits theoverall sensitivity of the receiver. An application’s noiserequirement has a signifi cant infl uence on the systemtopology, since the choice of topology strives to optimizethe overall signal-to-noise ratio, dynamic range andseveral other parameters. One problem in noise calculationsis translating between the various units used by thecomponents in the chain: namely the RF, IF/baseband,and digital (ADC) sections of the circuit.
上传时间： 2014-12-05
上传用户：cylnpy
Control systems are becoming increasingly dependent on digital processing and so require sensors able to provide direct digital inputs. Sensors based on time measurement, having outputs based on a frequency or phase, have an advantage over conventional analogue sensors in that their outputs can be measured directly in digital systems by pulse counting.
上传时间： 2013-10-08
上传用户：wuyuying
高速数字系统设计下载pdf:High-Speed Digital SystemDesign—A Handbook ofInterconnect Theory and DesignPracticesStephen H. HallGarrett W. HallJames A. McCallA Wiley-Interscience Publication JOHN WILEY & SONS, INC.New York • Chichester • Weinheim • Brisbane • Singapore • TorontoCopyright © 2000 by John Wiley & Sons, Inc.speeddigital systems at the platform level. The book walks the reader through everyrequired concept, from basic transmission line theory to digital timing analysis, high-speedmeasurement techniques, as well as many other topics. In doing so, a unique balancebetween theory and practical applications is achieved that will allow the reader not only tounderstand the nature of the problem, but also provide practical guidance to the solution.The level of theoretical understanding is such that the reader will be equipped to see beyondthe immediate practical application and solve problems not contained within these pages.Much of the information in this book has not been needed in past digital designs but isabsolutely necessary today. Most of the information covered here is not covered in standardcollege curricula, at least not in its focus on digital design, which is arguably one of the mostsignificant industries in electrical engineering.The focus of this book is on the design of robust high-volume, high-speed digital productssuch as computer systems, with particular attention paid to computer busses. However, thetheory presented is applicable to any high-speed digital system. All of the techniquescovered in this book have been applied in industry to actual digital products that have beensuccessfully produced and sold in high volume.Practicing engineers and graduate and undergraduate students who have completed basicelectromagnetic or microwave design classes are equipped to fully comprehend the theorypresented in this book. At a practical level, however, basic circuit theory is all thebackground required to apply the formulas in this book.
上传时间： 2013-10-26
上传用户：缥缈
OPTOELECTRONICS CIRCUIT COLLECTION AVALANCHE PHOTODIODE BIAS SUPPLY 1Provides an output voltage of 0V to +80V for reverse biasingan avalanche photodiode to control its gain. This circuit canalso be reconfigured to supply a 0V to –80V output.LINEAR TEC DRIVER–1This is a bridge-tied load (BTL) linear amplifier for drivinga thermoelectric cooler (TEC). It operates on a single +5Vsupply and can drive ±2A into a common TEC.LINEAR TEC DRIVER–2This is very similar to DRIVER–1 but its power output stagewas modified to operate from a single +3.3V supply in orderto increase its efficiency. Driving this amplifier from astandard +2.5V referenced signal causes the output transistorsto have unequal power dissipation.LINEAR TEC DRIVER–3This BTL TEC driver power output stage achieves very highefficiency by swinging very close to its supply rails, ±2.5V.This driver can also drive ±2A into a common TEC. Operationis shown with the power output stage operating on±1.5V supplies. Under these conditions, this linear amplifiercan achieve very high efficiency. Application ReportThe following collection of analog circuits may be useful in electro-optics applications such as optical networkingsystems. This page summarizes their salient characteristics.
上传时间： 2013-10-27
上传用户：落花无痕
Abstract: Using a wafer-level package (WLP) can reduce the overall size and cost of your solution.However when using a WLP IC, the printed circuit board (PCB) layout can become more complex and, ifnot carefully planned, result in an unreliable design. This article presents some PCB designconsiderations and general recommendations for choosing a 0.4mm- or 0.5mm-pitch WLP for yourapplication.
标签： Considerations Guidelines and Design
上传时间： 2013-10-14
上传用户：ysystc699
PADS-PowerLogic and PowerPcb实用教程
标签： PADS-PowerLogic PowerPcb and 实用教程
上传时间： 2014-12-24
上传用户：youmo81
The LTP5901 and LTP5902 require little external circuitry, as the devices references,decoupling and power supply filtering are integrated. The LTP5901 and LTP5902 will bemodularly certified for operation in the United States (FCC), Canada (IC) and theEuropean Union (CE).
标签： Integration LTP Hardware Guide
上传时间： 2013-11-22
上传用户：sunchao524
We provide complete power solutions with a full lineup of power managementproducts. This brochure provides an overview of our high performance DC/DC switching regulatorcontrollers for applications including datacom, telecom, industrial, automotive, medical, avionicsand control systems. We make power design easier with our industry-leading field applicationengineering support; a broad selection of demonstration boards with schematics, layout filesand parts lists; SwitcherCAD® software for simulation, application notes and comprehensivetechnical documentation.
上传时间： 2013-10-15
上传用户：lz4v4
Abstract: This application note illustrates an intermediate 8V switching power supply for an automotive radio and infotainment system.The design withstands the complete automotive input voltage range (including cold crank and load dump conditions), assuring a stable8V supply for common subsystems such as a CD driver, LCDs, and a radio module in modern infotainment systems. To avoiddisturbance in the AM and FM bands, the switching power supply runs at a fixed frequency of 2MHz, enabling an ideal solution forradio systems.
上传时间： 2013-11-20
上传用户：feitian920
Abstract: Investment in smart meters and smart grid end equipment continues to grow worldwide as countriestry to make their electric delivery systems more efficient. However, as critical as the electric deliveryinfrastructure is, it is normally not secured and thus subject to attack. This article describes the concept oflife-cycle security—the idea that embedded equipment in the smart grid must have security designed into theentire life of the product, even back to the contract manufacturer. We also talk about how life-cycle securityapplies to embedded equipment in the smart grid. Potential threats are discussed, as are potential solutionsto mitigate the risks posed by those threats.
上传时间： 2014-12-24
上传用户：熊少锋
