虫虫首页| 资源下载| 资源专辑| 精品软件
登录| 注册

电路版图设计

  • 串联谐振单相全桥逆变电路的设计

    串联谐振单相全桥逆变电路的设计              

    标签: 串联谐振 逆变电路

    上传时间: 2022-04-04

    上传用户:jiabin

  • 磷酸铁锂电池充电电路的设计及实验分析

    磷酸铁锂电池充电电路的设计及实验分析                

    标签: 磷酸锂电池 充电电路

    上传时间: 2022-04-05

    上传用户:

  • ST188光耦隔离+LM339四路比较器电路 Altium设计 硬件原理图+PCB文件

    ST188光耦隔离+LM339四路比较器电路 Altium设计 硬件原理图+PCB文件

    标签: st188 光耦隔离 lm339

    上传时间: 2022-04-06

    上传用户:

  • 基于IR2136的无刷直流电机驱动电路的设计

     基于IR2136的无刷直流电机驱动电路的设计,有需要的可以参考!

    标签: ir2136 无刷直流电机 驱动电路

    上传时间: 2022-04-09

    上传用户:

  • STM32单片机于DLP驱动电路的设计

    STM32单片机于DLP驱动电路的设计

    标签: stm32 单片机 dlp 驱动电路

    上传时间: 2022-04-10

    上传用户:

  • 反激型开关电源电路课程设计

    反激型开关电源电路课程设计

    标签: 开关电源

    上传时间: 2022-04-12

    上传用户:

  • 基于GL3520 USB3.0集线器USB HUB电路AD设计硬件原理图+PCB文件

    基于GL3520 USB3.0集线器USB HUB电路AD设计硬件原理图+PCB文件,ad 设计的工程文件,包括原理图及PCB印制板图,可以用Altium Designer(AD)软件打开或修改,可作为你产品设计的参考。

    标签: gl3520 usb3 集线器 usb hub

    上传时间: 2022-04-14

    上传用户:

  • CN3722 太阳能充电电路AD设计原理图+pcb+BOM文件

    CN3722 太阳能充电电路AD设计原理图+pcb+BOM文件

    标签: 太阳能充电

    上传时间: 2022-04-26

    上传用户:

  • 1MHz换能器驱动电路的设计

    超声波换能器作为一种实用的检测手段,能实现声波所携带的信息和电能之间转换。它的性能优良,价格低廉,操作方便,易于调试,因此在工农业生产中发挥着重要的作用。但目前换能器驱动电路的发射频率多为40 kHz,本文针对1 MHz的超声波换能器电路进行了设计,主要介绍了它的发射驱动电路和接收驱动电路的设计方案,并对它们的功能进行了详细地说明。最后搭建实验平台,并对电路的输入、输出模块进行了测试。实验结果表明,换能器电路运行良好,可以为超声波高精度测量领域的应用提供参考。As a practical means of detection, ultrasonic transducer can realize the conversion between theinformation carried by sound wave and electric energy.It has the advantages of excellent performance,low cost, convenient operation and debugging, so plays an important role in industrial and agriculturalproduction.However, the transmitting frequency of the driving circuit for most transducer is 40 kHz.Thecircuit of 1 MHz ultrasonic transducer is designed In this paper. It mainly introduces the emissive drivingcircuit and the receiving circuit design and the detailed function of them. Finally, the experimentalplatform is built, and the circuit of input and output were tested. Experiments show that the transducer' s...

    标签: 换能器 驱动电路

    上传时间: 2022-04-28

    上传用户:

  • 基于PSIM仿真的开关电源Boost电路的设计

    基于PSIM仿真软件,分析了Boost电路拓扑结构,设定了参数要求进行电路仿真设计,通过电路仿真软件PSIM对Boost电路工作在CCM模式下,合理设置占空比参数。实验结果表明理论分析与仿真的一致性和参数设计的正确性,输出电压和电流参数稳定,Boost电路输出效率高。This design is based on PSIM simulation software,analyzes the topology of Boost circuit,sets the parameter re- quirements for circuit simulation design,and reasonably sets the duty cycle parameters for Boost circuit working in CCM mode through PSIM simulation software.The experimental results show that the theoretical analysis and simulation are consis- tent and the parameter design is correct,the output voltage and current parameters are stable.

    标签: psim 开关电源 boost

    上传时间: 2022-05-04

    上传用户: