该应用报告描述了旋转检测器的实现，该旋转检测器使用一对可检测磁场的巨磁阻GMR（Giant Magneto-Resistive,）传感器。传感器的分布使它们不使用正交信号序列，这提供了讨论非正交情况如何配置SIF的机会。讨论了调试SIF应用程序的技术，提供了一个设计非正交进程状态机（processing state machines）的工具。
上传时间： 2013-10-21
上传用户：sammi
针对科研实验中对拉压千斤顶加载过程控制的需要，采用ATmega128单片机控制步进电机进而实现对执行系统的电动泵站实行自动控制。对力和位移的数据采集与处理及用步进电机控制电动泵站手柄的技术细节作了重点描述。通过单片机的A/D变换器对AMP放大模块采集的电桥信号作量化处理，千斤顶的操控手柄位置依电动油泵阀门开启的方向和大小作若干定位，单片机根据力或位移传感器信号，实时控制步进电机驱动手柄旋转到相应操控位置。 Abstract: This article describes the use of ATmega128 AVR microcontroller series of DBS electric pumping stations and QF100/200 separate twoway hydraulic jack to automate the process of manipulating the work of the technical content. Articles on force and displacement data acquisition and processing， and stepper motor control electric pump with the handle of the key technical details were described. Through the MCU’s A / D converter module is collected on the AMP amplification quantify the signal bridge， jack handle position control valve opening according to the direction of electric pumps for a number of positioning and size of the microcontroller based on force or displacement sensor signals， real-time control stepper motor drive control handle rotate to the appropriate location.
上传时间： 2014-01-16
上传用户：hasan2015
设计了一种基于PIC16C71单片机的数字水温配制阀。该配制阀采用NTC热敏电阻作温度传感器，与固定电阻组成简单分压电路作为水温测量电路，利用PIC16C71单片机内置的8位A/D转换器把热敏电阻上的模拟电压转换为数字量，PIC16C71单片机控制直流电机驱动混水阀调节冷热水的混合比例实现水温调节。给出了控制电路图，对水温测量电路的参数选择和测温精度作了详细讨论。实验和分析表明，选用阻值较大的NTC热敏电阻和分压电阻可较好地解决热敏电阻因功耗较大造成的热击穿问题。 Abstract: A digital valve for controlling water temperature based on PIC16C71 was presented in this paper.A bleeder circuit which consisted of a NTC thermistor as temperature sensor and a fixed resistance was designed as water temperature measuring circuit.The analog voltage on the thermistor was converted into digital signal by a 8-bit A/D converter embedded in PIC16C71. Based on the digital signal， the MCU PIC16C71 drived the valve by a DC motor to adjust the water temperature through adjusting the proportion of hot water and cold water.The circuit diagram of controller was given，the principle，the component parameters and the accuracy of measuring temperatures were also dissertated in detail. It was found by experiment and analysis that thermal breakdown of thermistor caused by high power could be solved by selecting thermistor and fixed resistance with high impedance value.
上传时间： 2013-11-08
上传用户：Yue Zhong
摘 要: 阀门开度仪以AT89C51单片机为核心, 通过在阀门电机轴上安装的电位计传感器获得阀 门电机轴的转动角位移, 从而得出阀门的开度, 达到自动检测的目的。详细介绍了串行控制的10 位A /D转换器TLC1549的特点和功能, 说明了TLC1549与AT89C51单片机在阀门开度仪中的硬件 电路和软件程序。实践证明, 该阀门开度仪数据采集准确可靠、工作稳定。 关键词: TLC1549; AT89C51单片机; 阀门开度
上传时间： 2013-10-14
上传用户：行者Xin
○1 RS232 串口 ○2 ISP程序下载接口 ○3 18B20 数字传感器接口 ○4 EEPROM ○5 七彩跑马灯 ○6 驱动芯片 ○7 蜂鸣器 ○8 继电器 ○9 直流电机接口 ○10 继电器输出口 ○11 步进电机接口 ○12 矩阵按键
上传时间： 2013-10-14
上传用户：semi1981
提出一种基于凌阳单片机的步进电机加减速的控制方法。采用凌阳科技推出的16位结构工控单片机SPMC75F2413A为控制器，由Allegro公司生产的两相步进电机专用驱动器件SLA7042M构成步进电机的驱动电路，在传统的3段直线加减速控制算法基础上增加至7段S形曲线加减速过程，控制步进电机的启动和停止。实验结果表明，该控制方法克服了直线加减速中不连续、易造成系统冲击的问题，整个系统实现柔性控制，电机启动、停止连续性能提高30%。 Abstract: The method of controlled stepping motor is referred based on SPMC75F2413A MCU， which adopts the 16 knots SPMC75F2413A MCU as the controller. The special-purpose actuation chip SLA7042M of two stepping motor produced by Allegro Corporation constituted to actuation electric circuit. The purpose of increasing to seven section of S shape curve based on the traditional three sections of straight line is to control the start and stop process of stepping motor. The experimental results show that the control method solves easy to pull-out and overshot problems. The overall system realizes flexible control， and the performance of motor start or stop continuity is increased 30%
上传时间： 2013-12-08
上传用户：jiangfire
首先研究CAN总线和SAE J1939协议，提出一种基于MC9S12HZ256微控制器的总线式汽车数字仪表解决方案。详细介绍SAE J1939协议的报文帧格式及应用层协议中发动机相关参数的定义，以及步进电机及其驱动和车速信号的处理方法。该数字仪表系统硬件平台由微处理器和信号采集和信息处理及显示等模块组成。软件设计部分编程实现了对CAN总线和各传感器数据的读取、处理。该系统能够实时反映车辆工况。 Abstract: In this paper，CAN bus and SAE J1939protocol are researched，and a vehicle digital instrument solution based on MC9S12HZ256MCU is proposed.The message frame format and some engine-related parameters’definition in SAE J1939application layer protocol are introduced in detail.Stepper motor and its driver，the methods of speed signal process-ing are also introduced.The hardware platform of vehicle digital instrument is composed by MCU，signal acquisition mod-ule，and signal processing and displaying module.Data receiving and processing from CAN bus and sensors are accom-plished by programming，and vehicle condition can be reflected in real-time.
上传时间： 2013-10-20
上传用户：huannan88
摘要 本设计以AT89S52单片机为中心控制器，由51最小系统及复位电路、电源和USB下载模块、发光二极管模块、蜂鸣器电路、数码管显示模块、矩阵键盘模块、点阵显示电路、继电器电路、温度传感器DS18B20模块、串口通信接口电路、电机驱动电路、时钟芯片DS1302模块、存储器AT24C02、AD转化模块、DA转化模块、旋转拨码开关、1602和12864液晶接口、电路外部RAM62256模块组成。
上传时间： 2013-10-13
上传用户：爺的气质
为了提高环境参数采集的自动化水平，提升效率，设计了无线传感器系统。本系统运用了传感器技术、通信技术和单片机技术，实现了对环境温度、湿度、光照度以及可燃性气体浓度等参数的检测。它能够实时地与上位机进行无线通信，满足对环境参数实时监测的要求。 Abstract: In order to increase the degree of automation and improve the efficiency of the environment monitoring parameters，the wireless sensor system was developed.Combining with the technique of sensor,automatic monitoring，communication and single-chip microcomputer，it realized real-time monitoring environment parameters,such as temperature，humidity，illumination，concentration of com- bustible gas and so on.At the same time it can communicate with upper personal computers，satisfy the desire of real-time monitoring.
上传时间： 2013-11-22
上传用户：longlong12345678
一、 概述 1，多功能单片机开发板，板载资源非常丰富，仅是包括的功能(芯片)有： 步进电机驱动芯片ULN2003、 八路并行AD转换芯片ADC0804、 八路并行DA转换芯片DAC0832、 光电耦合(转换)芯片MOC3063、 八路锁存器芯片74HC573、 实时时钟芯片DS1302及备用电池、 IIC总线芯片AT24C02、 串行下载芯片MAX232CPE， 双向可控硅BTA06-600B、 4*4矩阵键盘、 4位独立按键、 DC5V SONGLE继电器、 5V蜂鸣器、 八位八段共阴数码管 5V稳压集成块78M05 八路发光二极管显示 另还有功能接口(标准配置没有芯片但留有接口，可直接连接使用)： 单总线温度传感器DS18B2接口、
上传时间： 2013-10-10
上传用户：mickey008
