电<b>液位</b>置

4位八段数码管的十进制加计数仿真实验(含电路图和仿真文件)

4位八段数码管的十进制加计数仿真实验，程序采用汇编语言编写。此程序在仿真软件上与EDN-51实验板上均通过。仿真图中的数码管位驱动采用74HC04，如按EDN-51板上用想同的PNP三极管驱动在仿真软件上则无法正常显示。程序共分5块，STAR0为数据初始化，STAR2为计数子程序，STAR3为4位数码管动态显示子程序，STAR4为按键扫描子程序，STS00是延时子程序。由于EDN-51实验板上没装BCD译码器，所以编写程序比较烦琐。程序如下： ORG 0000H LJMP STAR0 ;转程序 SRAR0ORG 0200H ;程序地址 0200HSTAR0: CLR 00 ;位 00 清 0 MOV P1,#0FFH ;#0FFH-->P1 MOV P2,#0FH ;#0FH-->P2 MOV P0,#0FFH ;#0FFH-->P0 MOV 30H,#00H ;#00H-->30H MOV 31H,#00H ;#00H-->30H MOV 32H,#00H ;#00H-->30H MOV 33H,#00H ;#00H-->30H LJMP STAR3 ;转程序 SRAR3STAR2: MOV A,#0AH ;#0AH-->A INC 30H ;30H+1 CJNE A,30H,STJE ;30H 与 A 比较,不等转移 STJE MOV 30H,#00H ;#00H-->30H INC 31H ;31H+1 CJNE A,31H,STJE ;31H 与 A 比较,不等转移 STJE MOV 31H,#00H ;#00H-->31H INC 32H ;32H+1 CJNE A,32H,STJE ;32H 与 A 比较,不等转移 STJE MOV 32H,#00H ;#00H-->32H INC 33H ;33H+1 CJNE A,33H,STJE ;33H 与 A 比较,不等转移 STJE MOV 33H,#00H ;#00H-->33H MOV 32H,#00H ;#00H-->32H MOV 31H,#00H ;#00H-->31H MOV 30H,#00H ;#00H-->30HSTJE: RET ;子程序调用返回STAR3: MOV R0,#30H ;#30H-->R0 MOV R6,#0F7H ;#0F7H-->R6SMG0: MOV P1,#0FFH ;#0FFH-->P1 MOV A,R6 ;R6-->A MOV P1,A ;A-->P1 RR A ;A向右移一位 MOV R6,A ;A-->R6 MOV A,@R0 ;@R0-->A ADD A,#04H ;#04H-->A MOVC A,@A+PC ;A+PC--> MOV P0,A ;A-->P0 AJMP SMG1 ;转程序 SMG1SDATA: DB 0C0H,0F9H,0A4H,0B0H,99H DB 92H,82H,0F8H,80H,90H SMG1: LCALL STAR4 ;转子程序 SRAR4 LCALL STS00 ;转子程序 STS00 INC R0 ;R0+1 CJNE R6,#07FH,SMG0 ;#07FH 与 R6 比较,不等转移 SMG0 AJMP STAR3 ;转程序 SRAR3STAR4: JNB P2.0,ST1 ;P2.0=0 转 ST1 CLR 00 ;位 00 清 0 SJMP ST3 ;转ST3ST1: JNB 00,ST2 ;位 00=0 转 ST2 SJMP ST3 ;转 ST3ST2: LCALL STAR2 ;调子程序 STAR2 SETB 00 ;位 00 置 1ST3: RET ;子程序调用返回ORG 0100H ;地址 0100HSTS00: MOV 60H,#003H ;#003H-->60H (211)DE001: MOV 61H,#0FFH ;#0FFH-->61H (255)DE002: DJNZ 61H,DE002 ;61H 减 1 不等于 0 转 DE002 DJNZ 60H,DE001 ;60H 减 1 不等于 0 转 DE001 RET ;子程序调用返回 END ;结束上次的程序共有293句，经小组成员建议，本人经几天的研究写了下面的这个程序，现在的程序用了63句，精简了230句。功能没有减。如谁有更简练的程序，请发上来，大家一起学习。 4位八段数码管的十进制加计数仿真实验(含电路图和仿真文件)

标签： 数码管十进制仿真实验仿真

上传时间： 2013-10-11

上传用户：sssl
SLPC可编程调节器的基本使用

1、能读懂显示器的数字意义。2、能正确装卸整定盘，合理检查调节器的工作状况。3、能正确设置给定值、正反作用方式、量程设置等基本操作。熟悉SLPC可编程调节器的工作原理及结构特点，明确其主要功能。重点：熟悉调节器的功能与结构特点，学会其基本操作。难点：SLPC可编程调节器的合理操作。解决办法：教师操作演示的知识学习——学生动手实践的能力提高。通过前面四个项目的学习，同学们已经掌握了单回路的过程控制技术，从而也就达到了本课程的基本要求。但是对照本课程总的目标——电加热锅炉的开发与实施，我们还尚未完全解决问题：实际的电加热锅炉控制目标是要产生符合要求的蒸汽，而我们前面所完成的锅炉控制都是对液位的控制，是对问题的简化；同时，由于锅炉本身的工艺特点，这使得实际锅炉的控制方法有其特殊性。要真正解决电加热锅炉的控制问题，先要实现蒸汽流量的正确测量，以便实现对锅炉液位的准确控制与安全运行。由于蒸汽流量与温度、压力有直接关系，必须对流量进行温度、压力补偿处理。

标签： SLPC 可编程调节器

上传时间： 2013-12-05

上传用户：taozhengxin
磁芯电感器的谐波失真分析

磁芯电感器的谐波失真分析摘要：简述了改进铁氧体软磁材料比损耗系数和磁滞常数ηB，从而降低总谐波失真THD的历史过程，分析了诸多因数对谐波测量的影响，提出了磁心性能的调控方向。关键词：比损耗系数，磁滞常数ηB ，直流偏置特性DC-Bias，总谐波失真THD Analysis on THD of the fer rite co res u se d i n i nductancShi Yan Nanjing Finemag Technology Co. Ltd., Nanjing 210033 Abstract: Histrory of decreasing THD by improving the ratio loss coefficient and hysteresis constant of soft magnetic ferrite is briefly narrated. The effect of many factors which affect the harmonic wave testing is analysed. The way of improving the performance of ferrite cores is put forward. Key words: ratio loss coefficient，hysteresis constant，DC-Bias，THD 近年来，变压器生产厂家和软磁铁氧体生产厂家，在电感器和变压器产品的总谐波失真指标控制上，进行了深入的探讨和广泛的合作，逐步弄清了一些似是而非的问题。从工艺技术上采取了不少有效措施，促进了质量问题的迅速解决。本文将就此热门话题作一些粗浅探讨。一、历史回顾总谐波失真（Total harmonic distortion），简称THD，并不是什么新的概念，早在几十年前的载波通信技术中就已有严格要求<1>。1978年邮电部公布的标准YD/Z17－78“载波用铁氧体罐形磁心”中，规定了高μQ材料制作的无中心柱配对罐形磁心详细的测试电路和方法。如图一电路所示，利用LC组成的150KHz低通滤波器在高电平输入的情况下测量磁心产生的非线性失真。这种相对比较的实用方法，专用于无中心柱配对罐形磁心的谐波衰耗测试。这种磁心主要用于载波电报、电话设备的遥测振荡器和线路放大器系统，其非线性失真有很严格的要求。图中 ZD —— QF867 型阻容式载频振荡器，输出阻抗 150Ω， Ld47 —— 47KHz 低通滤波器，阻抗 150Ω，阻带衰耗大于61dB， Lg88 ——并联高低通滤波器，阻抗 150Ω，三次谐波衰耗大于61dB Ld88 ——并联高低通滤波器，阻抗 150Ω，三次谐波衰耗大于61dB FD —— 30～50KHz 放大器，阻抗 150Ω，增益不小于 43 dB，三次谐波衰耗b3(0)≥91 dB, DP —— Qp373 选频电平表，输入高阻抗， L ——被测无心罐形磁心及线圈， C ——聚苯乙烯薄膜电容器CMO-100V-707APF±0.5%,二只。测量时，所配用线圈应用丝包铜电磁线SQJ9×0.12(JB661-75)在直径为16.1mm的线架上绕制 120 匝，（线架为一格），其空心电感值为 318μH（误差1％）被测磁心配对安装好后，先调节振荡器频率为 36.6～40KHz，使输出电平值为+17.4 dB，即选频表在 22′端子测得的主波电平（P2）为+17.4 dB，然后在33′端子处测得输出的三次谐波电平（P3），则三次谐波衰耗值为：b3(+2)= P2+S+ P3 式中：S 为放大器增益dB 从以往的资料引证，就可以发现谐波失真的测量是一项很精细的工作，其中测量系统的高、低通滤波器，信号源和放大器本身的三次谐波衰耗控制很严，阻抗必须匹配，薄膜电容器的非线性也有相应要求。滤波器的电感全由不带任何磁介质的大空心线圈绕成，以保证本身的“洁净” ，不至于造成对磁心分选的误判。为了满足多路通信整机的小型化和稳定性要求，必须生产低损耗高稳定磁心。上世纪 70 年代初，1409 所和四机部、邮电部各厂，从工艺上改变了推板空气窑烧结，出窑后经真空罐冷却的落后方式，改用真空炉，并控制烧结、冷却气氛。技术上采用共沉淀法攻关试制出了μQ乘积 60 万和 100 万的低损耗高稳定材料，在此基础上，还实现了高μ7000～10000材料的突破，从而大大缩短了与国外企业的技术差异。当时正处于通信技术由FDM（频率划分调制）向PCM（脉冲编码调制）转换时期，日本人明石雅夫发表了μQ乘积125 万为 0.8×10 ，100KHz）的超优铁氧体材料<3>，其磁滞系数降为优铁

标签： 磁芯电感器分谐波失真

上传时间： 2013-12-15

上传用户：天空说我在
51单片机电子日历电子日历

51单片机电子日历电子日历，有时间显示、闹铃、日期、秒表及键盘设置功能功能键A: 设置位数字+1 闹钟模式下为闹钟开关秒表模式下为记时开关功能键B: 设置位数字-1 闹钟模式下为闹钟开关功能键C:设置模式及设置位选择秒表模式下为清零键功能键D:在四种工作模式下切换设置闹钟开关

标签： 电子日历 51单片机

上传时间： 2013-12-16

上传用户：zycidjl
四位有符号数的加法

四位有符号数的加法，通过拨位期置数，然后通过数码管显示结果

标签： 符号加法

上传时间： 2016-08-25

上传用户：亚亚娟娟123
红外解码程序

/* * _168ZHONGDUAN2.c * * Created: 2014/11/2 15:12:45 * Author: lenovo */ #include <avr/io.h> #include <avr/iom168pa.h> #include <avr/interrupt.h> #include <util/delay.h> #include <avr/eeprom.h> //#include <util/delay_basic.h> //unsigned char const SEGtable[]={0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f,0x6f,0x40}; #define BIT(x) (1<<(x)) #include<avr/signal.h> #include<avr/pgmspace.h> #include<util/delay.h> #include<avr/eeprom.h> #define setb(val,bitn) (val|=(1<<(bitn)))//设置某IO口某位为1 #define clr(val,bitn) (val&=~(1<<(bitn)))//设置某IO口某位为0 #define get(val,bitn) (val&(1<<(bitn)))//读取某位状态 //uchar ACT[8] ={0xfe,0xfd,0xfb,0xf7,0xef,0xdf,0xbf,0x7f}; #define CPL_BIT(x,y) (x^=(1<<y)) #define CLR_BIT(x,y) (x&=~(1<<y)) #define SET_1(a,b) a|=(1<<b) #define CLE_0(a,b) a&=~(1<<b) /*------宏定义------*/ #include <avr/wdt.h> #include <avr/sleep.h> #include <avr/interrupt.h> #include <avr/pgmspace.h> #include <util/delay.h> #include <avr/eeprom.h> #define setb(val,bitn) (val|=(1<<(bitn)))//设置某IO口某位为1 #define clr(val,bitn) (val&=~(1<<(bitn)))//设置某IO口某位为0 #define get(val,bitn) (val&(1<<(bitn)))//读取某位状态 #define uint8 unsigned char #define uint16 unsigned int #define P_LCDCS1 setb(PORTB,5) #define P_LCDCS0 clr(PORTB,5) #define P_LCDRST1 setb(PORTB,1) #define P_LCDRST0 clr(PORTB,1) #define P_LCDRS1 setb(PORTB,2) #define P_LCDRS0 clr(PORTB,2) #define P_LCDDAT1 setb(PORTB,4) #define P_LCDDAT0 clr(PORTB,4) #define P_LCDCLK1 setb(PORTB,3) #define P_LCDCLK0 clr(PORTB,3) //#define LCD_ //-----页地址定义----- #define Page1 0 #define Page2 1 #define Page3 2 #define Page4 3 #define Page5 4 #define Page6 5 #define Page7 6 #define Page8 7 //-----列地址定义-----每8列地址增1 #define List8_1 0 #define List8_2 7 #define List8_3 15 #define List8_4 23 #define List8_5 31 #define List8_6 39 #define List8_7 47 #define List8_8 55 #define List8_9 63 #define List8_10 71 #define List8_11 79 #define List8_12 87 #define List8_13 95 #define List8_14 103 #define List8_15 111 #define List8_16 119 //#define List8_17 127 //-----列地址定义-----每16列地址增1 #define List16_1 0 #define List16_2 15 #define List16_3 31 #define List16_4 47 #define List16_5 63 #define List16_6 79 #define List16_7 95 #define List16_8 111 //---------------------------------- #define STR_CHARG "Charge" //提示充电 #define STR_PRCE "%" //电量百分比 #define STR_ERR "Err" //出错显示 #define STR_OFF "OFF" //关机显示 //待机显示 #define STR_WAIT1 "Portable UPS" #define STR_WAIT2 "110V/60HZ" #define STR_WAIT3 "Select:DC OR AC" #define STR_WAIT4 "BATTERY:" //开机显示 #define STR_OUTSTATUS "Out Status:" #define STR_DCOUT12V "DC12V" #define STR_DCOUT5V "DC5V" #define STR_ACOUT "AC110V" //#define STR_MAOHAO ":" //====================================== extern uint8 LOCKA[2][16] ; //extern uint8 code BATS[10][16] ; extern uint8 BAT2S[12][32] ; extern uint8 NC[] ; extern uint8 mao_hao[] ; extern uint8 num1[] ; extern uint8 num2[] ; extern uint8 num3[] ; extern uint8 num4[] ; extern uint8 num5[] ; extern uint8 num6[] ; extern uint8 num7[] ; extern uint8 num8[] ; extern uint8 num9[] ; extern uint8 Tab_Ascii_8x16[95][16] ; extern uint8 Tab_Ascii_5x7[95][5] ; extern uint8 zhuang1[] ; extern uint8 tai1[] ; extern uint8 shi1[] ; extern uint8 yong1[] ; //---------------------------------- //extern void LcdWriteCommand(uint8 data1) ; extern void Display_Graphic_32x32(uint8 page,uint8 column,uint8 *dp) ; extern void Display_Graphic_32x16(uint8 page,uint8 column,uint8 *dp) ; extern void Display_Graphic_16x16(uint8 page,uint8 column,uint8 *dp) ; extern void Display_Graphic_8x16(uint8 page,uint8 column,uint8 *dp) ; extern void Display_String_8x16(uint8 page,uint8 column,uint8 *text) ; extern void Display_Num_8x16(uint8 page,uint8 column,uint8 Num) ; extern void Display_Digital_8x16(uint8 page,uint8 column,uint8 *a) ; extern void Display_Nop_8x16(uint8 page,uint8 column,uint8 DatLong) ; extern void Display_String_5x7(uint8 page,uint8 column,uint8 *text) ; extern void Full_Display(void) ; extern void Clear_Screen(void) ; extern void Init_lcd12864(void) ; //#endif //========c12864.c============================================== /*************************************************** LCD:晶联讯电子 JLX12864G-086-PN(不带字库IC-UC1701X) 仅支持串行驱动方式 ***************************************************/ //#include "global.h" //#include "c12864.h" #define Tab_Ascii_8x16_CALL1 //粗体字形 #define Tab_Ascii_8x16_CALL2 //细体字形 #define Tab_Ascii_5x7_CALL #define Display_Graphic_32x32_CALL #define Display_Graphic_32x16_CALL #define Display_Graphic_16x16_CALL #define Display_Graphic_8x16_CALL #define Display_String_8x16_CALL //显示字符串 #define Display_Num_8x16_CALL //显示单个数据0-9 #define Display_Digital_8x16_CALL //显示数据0-9999 #define Display_Nop_8x16_CALL //填充8*16的空字符N个 #define Display_String_5x7_CALL #define Full_Display_CALL //============================================================================== uint8 aa[]={0,1,2,3,4,5,6,7,8,9}; uint8 LOCKA[2][16]={ //-- 童锁符号 -- //-- 此字体下对应的点阵为：宽x高=16x16 -- //0x00, 0x00, 0xc0, 0xe0, 0xf0, 0xd8, 0xcc, 0xc4, 0xc4, 0xcc, 0xd8, 0xf0, 0xe0, 0xc0, 0x00, 0x00, //0x00, 0x00, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x00, 0x00, 0x00, 0x00, 0xc0, 0xe0, 0xb0, 0x98, 0x8c, 0x8c, 0x8c, 0x8c, 0x98, 0xb0, 0xe0, 0xc0, 0x00, 0x00, 0x00, 0x00, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x00, 0x00, } ; const PROGMEM uint8_t BATS[10][16]={ //-- 电池符号 -- //-- 此字体下对应的点阵为：宽x高=16x16 -- 0x00, 0x00, 0x00, 0xf8, 0x08, 0x08, 0x0c, 0x0e, 0x0e, 0x0c, 0x08, 0x08, 0xf8, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x7f, 0x40, 0x40, 0x40, 0x40, 0x40, 0x40, 0x40, 0x40, 0x7f, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xf8, 0x08, 0x08, 0x0c, 0x0e, 0x0e, 0x0c, 0x08, 0x08, 0xf8, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x7f, 0x70, 0x70, 0x70, 0x70, 0x70, 0x70, 0x70, 0x70, 0x7f, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xf8, 0x08, 0x08, 0x0c, 0x0e, 0x0e, 0x0c, 0x08, 0x08, 0xf8, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x7f, 0x7e, 0x7e, 0x7e, 0x7e, 0x7e, 0x7e, 0x7e, 0x7e, 0x7f, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xf8, 0xc8, 0xc8, 0xcc, 0xce, 0xce, 0xcc, 0xc8, 0xc8, 0xf8, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x7f, 0x7f, 0x7f, 0x7f, 0x7f, 0x7f, 0x7f, 0x7f, 0x7f, 0x7f, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xf8, 0xf8, 0xf8, 0xfc, 0xfe, 0xfe, 0xfc, 0xf8, 0xf8, 0xf8, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x7f, 0x7f, 0x7f, 0x7f, 0x7f, 0x7f, 0x7f, 0x7f, 0x7f, 0x7f, 0x00, 0x00, 0x00, }; const PROGMEM uint8_t BAT2S1[12][32]={ /*-- 电池符号 --*/ /*-- 此字体下对应的点阵为：宽x高=32x16 --*/ {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xf8, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0xf8, 0xc0, 0x80}, {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x3f, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x3f, 0x07, 0x03}, {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xf8, 0x08, 0x08, 0xe8, 0xe8, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0xf8, 0xc0, 0x80}, {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x3f, 0x20, 0x20, 0x2f, 0x2f, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x3f, 0x07, 0x03}, {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xf8, 0x08, 0x08, 0xe8, 0xe8, 0x08, 0x08, 0xe8, 0xe8, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0xf8, 0xc0, 0x80}, {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x3f, 0x20, 0x20, 0x2f, 0x2f, 0x20, 0x20, 0x2f, 0x2f, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x3f, 0x07, 0x03}, {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xf8, 0x08, 0x08, 0xe8, 0xe8, 0x08, 0x08, 0xe8, 0xe8, 0x08, 0x08, 0xe8, 0xe8, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0xf8, 0xc0, 0x80}, {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x3f, 0x20, 0x20, 0x2f, 0x2f, 0x20, 0x20, 0x2f, 0x2f, 0x20, 0x20, 0x2f, 0x2f, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x3f, 0x07, 0x03}, {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xf8, 0x08, 0x08, 0xe8, 0xe8, 0x08, 0x08, 0xe8, 0xe8, 0x08, 0x08, 0xe8, 0xe8, 0x08, 0x08, 0xe8, 0xe8, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0xf8, 0xc0, 0x80}, {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x3f, 0x20, 0x20, 0x2f, 0x2f, 0x20, 0x20, 0x2f, 0x2f, 0x20, 0x20, 0x2f, 0x2f, 0x20, 0x20, 0x2f, 0x2f, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x3f, 0x07, 0x03}, {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xf8, 0x08, 0x08, 0xe8, 0xe8, 0x08, 0x08, 0xe8, 0xe8, 0x08, 0x08, 0xe8, 0xe8, 0x08, 0x08, 0xe8, 0xe8, 0x08, 0x08, 0xe8, 0xe8, 0x08, 0x08, 0xf8, 0xc0, 0x80}, {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x3f, 0x20, 0x20, 0x2f, 0x2f, 0x20, 0x20, 0x2f, 0x2f, 0x20, 0x20, 0x2f, 0x2f, 0x20, 0x20, 0x2f, 0x2f, 0x20, 0x20, 0x2f, 0x2f, 0x20, 0x20, 0x3f, 0x07, 0x03}, } ; const PROGMEM uint8_t BAT2S2[2][32]={ //-- 电池符号不显示 -- //-- 此字体下对应的点阵为：宽x高=32x16 -- 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, } ; uint8 NC[]={ /*-- 文字: 空符号 --*/ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, } ; uint8 mao_hao[]={ /*-- 文字: : (冒号） --*/ /*-- 宋体12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x00,0x00,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00}; uint8 num0[]={ /*-- 文字: 0 --*/ /*-- 宋体12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x0F,0x10,0x20,0x20,0x10,0x0F,0x00 }; uint8 num1[]={ /*-- 文字: 1 --*/ /*-- 宋体12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00 }; uint8 num2[]={ /*-- 文字: 2 --*/ /*-- 宋体12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x70,0x08,0x08,0x08,0x88,0x70,0x00,0x00,0x30,0x28,0x24,0x22,0x21,0x30,0x00 //细体 //0x08,0x0C,0x84,0xC4,0x64,0x3C,0x18,0x00,0x0E,0x0F,0x09,0x08,0x08,0x0C,0x0C,0x00, // 粗体 }; uint8 num3[]={ /*-- 文字: 3 --*/ /*-- 宋体12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x30,0x08,0x88,0x88,0x48,0x30,0x00,0x00,0x18,0x20,0x20,0x20,0x11,0x0E,0x00 }; uint8 num4[]={ /*-- 文字: 4 --*/ /*-- 宋体12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x00,0xC0,0x20,0x10,0xF8,0x00,0x00,0x00,0x07,0x04,0x24,0x24,0x3F,0x24,0x00 }; uint8 num5[]={ /*-- 文字: 5 --*/ /*-- 宋体12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0xF8,0x08,0x88,0x88,0x08,0x08,0x00,0x00,0x19,0x21,0x20,0x20,0x11,0x0E,0x00 }; uint8 num6[]={ /*-- 文字: 6 --*/ /*-- 宋体12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0xE0,0x10,0x88,0x88,0x18,0x00,0x00,0x00,0x0F,0x11,0x20,0x20,0x11,0x0E,0x00 }; uint8 num7[]={ /*-- 文字: 7 --*/ /*-- 宋体12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x38,0x08,0x08,0xC8,0x38,0x08,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0x00 }; uint8 num8[]={ /*-- 文字: 8 --*/ /*-- 宋体12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x70,0x88,0x08,0x08,0x88,0x70,0x00,0x00,0x1C,0x22,0x21,0x21,0x22,0x1C,0x00 }; uint8 num9[]={ /*-- 文字: 9 --*/ /*-- 宋体12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x00,0x31,0x22,0x22,0x11,0x0F,0x00 }; //=======8x16======================================================================= #ifdef Display_String_8x16_CALL //Tab_Ascii_8x16_CALL const PROGMEM uint8_t Tab_Ascii_8x161[95][16]={ //粗体字形 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, // - - 0x00,0x00,0x38,0xFC,0xFC,0x38,0x00,0x00,0x00,0x00,0x00,0x0D,0x0D,0x00,0x00,0x00, // -!- 0x00,0x0E,0x1E,0x00,0x00,0x1E,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, // -"- 0x20,0xF8,0xF8,0x20,0xF8,0xF8,0x20,0x00,0x02,0x0F,0x0F,0x02,0x0F,0x0F,0x02,0x00, // -#- 0x38,0x7C,0x44,0x47,0x47,0xCC,0x98,0x00,0x03,0x06,0x04,0x1C,0x1C,0x07,0x03,0x00, // -$- 0x30,0x30,0x00,0x80,0xC0,0x60,0x30,0x00,0x0C,0x06,0x03,0x01,0x00,0x0C,0x0C,0x00, // -%- 0x80,0xD8,0x7C,0xE4,0xBC,0xD8,0x40,0x00,0x07,0x0F,0x08,0x08,0x07,0x0F,0x08,0x00, // -&- 0x00,0x10,0x1E,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, // -'- 0x00,0x00,0xF0,0xF8,0x0C,0x04,0x00,0x00,0x00,0x00,0x03,0x07,0x0C,0x08,0x00,0x00, // -(- 0x00,0x00,0x04,0x0C,0xF8,0xF0,0x00,0x00,0x00,0x00,0x08,0x0C,0x07,0x03,0x00,0x00, // -)- 0x80,0xA0,0xE0,0xC0,0xC0,0xE0,0xA0,0x80,0x00,0x02,0x03,0x01,0x01,0x03,0x02,0x00, // -*- 0x00,0x80,0x80,0xE0,0xE0,0x80,0x80,0x00,0x00,0x00,0x00,0x03,0x03,0x00,0x00,0x00, // -+- 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x10,0x1E,0x0E,0x00,0x00,0x00, // -,- 0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, // --- 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0C,0x0C,0x00,0x00,0x00, // -.- 0x00,0x00,0x00,0x80,0xC0,0x60,0x30,0x00,0x0C,0x06,0x03,0x01,0x00,0x00,0x00,0x00, // -/- 0xF8,0xFC,0x04,0xC4,0x24,0xFC,0xF8,0x00,0x07,0x0F,0x09,0x08,0x08,0x0F,0x07,0x00, // -0- 0x00,0x10,0x18,0xFC,0xFC,0x00,0x00,0x00,0x00,0x08,0x08,0x0F,0x0F,0x08,0x08,0x00, // -1- 0x08,0x0C,0x84,0xC4,0x64,0x3C,0x18,0x00,0x0E,0x0F,0x09,0x08,0x08,0x0C,0x0C,0x00, // -2- 0x08,0x0C,0x44,0x44,0x44,0xFC,0xB8,0x00,0x04,0x0C,0x08,0x08,0x08,0x0F,0x07,0x00, // -3- 0xC0,0xE0,0xB0,0x98,0xFC,0xFC,0x80,0x00,0x00,0x00,0x00,0x08,0x0F,0x0F,0x08,0x00, // -4- 0x7C,0x7C,0x44,0x44,0xC4,0xC4,0x84,0x00,0x04,0x0C,0x08,0x08,0x08,0x0F,0x07,0x00, // -5- 0xF0,0xF8,0x4C,0x44,0x44,0xC0,0x80,0x00,0x07,0x0F,0x08,0x08,0x08,0x0F,0x07,0x00, // -6- 0x0C,0x0C,0x04,0x84,0xC4,0x7C,0x3C,0x00,0x00,0x00,0x0F,0x0F,0x00,0x00,0x00,0x00, // -7- 0xB8,0xFC,0x44,0x44,0x44,0xFC,0xB8,0x00,0x07,0x0F,0x08,0x08,0x08,0x0F,0x07,0x00, // -8- 0x38,0x7C,0x44,0x44,0x44,0xFC,0xF8,0x00,0x00,0x08,0x08,0x08,0x0C,0x07,0x03,0x00, // -9- 0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00,0x00,0x06,0x06,0x00,0x00,0x00, // -:- 0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00,0x08,0x0E,0x06,0x00,0x00,0x00, // -;- 0x00,0x80,0xC0,0x60,0x30,0x18,0x08,0x00,0x00,0x00,0x01,0x03,0x06,0x0C,0x08,0x00, // -<- 0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x00,0x02,0x02,0x02,0x02,0x02,0x02,0x02,0x00, // -=- 0x00,0x08,0x18,0x30,0x60,0xC0,0x80,0x00,0x00,0x08,0x0C,0x06,0x03,0x01,0x00,0x00, // ->- 0x18,0x1C,0x04,0xC4,0xE4,0x3C,0x18,0x00,0x00,0x00,0x00,0x0D,0x0D,0x00,0x00,0x00, // -?- 0xF0,0xF8,0x08,0xC8,0xC8,0xF8,0xF0,0x00,0x07,0x0F,0x08,0x0B,0x0B,0x0B,0x01,0x00, // -@- 0xE0,0xF0,0x98,0x8C,0x98,0xF0,0xE0,0x00,0x0F,0x0F,0x00,0x00,0x00,0x0F,0x0F,0x00, // -A- 0x04,0xFC,0xFC,0x44,0x44,0xFC,0xB8,0x00,0x08,0x0F,0x0F,0x08,0x08,0x0F,0x07,0x00, // -B- 0xF0,0xF8,0x0C,0x04,0x04,0x0C,0x18,0x00,0x03,0x07,0x0C,0x08,0x08,0x0C,0x06,0x00, // -C- 0x04,0xFC,0xFC,0x04,0x0C,0xF8,0xF0,0x00,0x08,0x0F,0x0F,0x08,0x0C,0x07,0x03,0x00, // -D- 0x04,0xFC,0xFC,0x44,0xE4,0x0C,0x1C,0x00,0x08,0x0F,0x0F,0x08,0x08,0x0C,0x0E,0x00, // -E- 0x04,0xFC,0xFC,0x44,0xE4,0x0C,0x1C,0x00,0x08,0x0F,0x0F,0x08,0x00,0x00,0x00,0x00, // -F- 0xF0,0xF8,0x0C,0x84,0x84,0x8C,0x98,0x00,0x03,0x07,0x0C,0x08,0x08,0x07,0x0F,0x00, // -G- 0xFC,0xFC,0x40,0x40,0x40,0xFC,0xFC,0x00,0x0F,0x0F,0x00,0x00,0x00,0x0F,0x0F,0x00, // -H- 0x00,0x00,0x04,0xFC,0xFC,0x04,0x00,0x00,0x00,0x00,0x08,0x0F,0x0F,0x08,0x00,0x00, // -I- 0x00,0x00,0x00,0x04,0xFC,0xFC,0x04,0x00,0x07,0x0F,0x08,0x08,0x0F,0x07,0x00,0x00, // -J- 0x04,0xFC,0xFC,0xC0,0xF0,0x3C,0x0C,0x00,0x08,0x0F,0x0F,0x00,0x01,0x0F,0x0E,0x00, // -K- 0x04,0xFC,0xFC,0x04,0x00,0x00,0x00,0x00,0x08,0x0F,0x0F,0x08,0x08,0x0C,0x0E,0x00, // -L- 0xFC,0xFC,0x38,0x70,0x38,0xFC,0xFC,0x00,0x0F,0x0F,0x00,0x00,0x00,0x0F,0x0F,0x00, // -M- 0xFC,0xFC,0x38,0x70,0xE0,0xFC,0xFC,0x00,0x0F,0x0F,0x00,0x00,0x00,0x0F,0x0F,0x00, // -N- 0xF0,0xF8,0x0C,0x04,0x0C,0xF8,0xF0,0x00,0x03,0x07,0x0C,0x08,0x0C,0x07,0x03,0x00, // -O- 0x04,0xFC,0xFC,0x44,0x44,0x7C,0x38,0x00,0x08,0x0F,0x0F,0x08,0x00,0x00,0x00,0x00, // -P- 0xF8,0xFC,0x04,0x04,0x04,0xFC,0xF8,0x00,0x07,0x0F,0x08,0x0E,0x3C,0x3F,0x27,0x00, // -Q- 0x04,0xFC,0xFC,0x44,0xC4,0xFC,0x38,0x00,0x08,0x0F,0x0F,0x00,0x00,0x0F,0x0F,0x00, // -R- 0x18,0x3C,0x64,0x44,0xC4,0x9C,0x18,0x00,0x06,0x0E,0x08,0x08,0x08,0x0F,0x07,0x00, // -S- 0x00,0x1C,0x0C,0xFC,0xFC,0x0C,0x1C,0x00,0x00,0x00,0x08,0x0F,0x0F,0x08,0x00,0x00, // -T- 0xFC,0xFC,0x00,0x00,0x00,0xFC,0xFC,0x00,0x07,0x0F,0x08,0x08,0x08,0x0F,0x07,0x00, // -U- 0xFC,0xFC,0x00,0x00,0x00,0xFC,0xFC,0x00,0x01,0x03,0x06,0x0C,0x06,0x03,0x01,0x00, // -V- 0xFC,0xFC,0x00,0x80,0x00,0xFC,0xFC,0x00,0x03,0x0F,0x0E,0x03,0x0E,0x0F,0x03,0x00, // -W- 0x0C,0x3C,0xF0,0xC0,0xF0,0x3C,0x0C,0x00,0x0C,0x0F,0x03,0x00,0x03,0x0F,0x0C,0x00, // -X- 0x00,0x3C,0x7C,0xC0,0xC0,0x7C,0x3C,0x00,0x00,0x00,0x08,0x0F,0x0F,0x08,0x00,0x00, // -Y- 0x1C,0x0C,0x84,0xC4,0x64,0x3C,0x1C,0x00,0x0E,0x0F,0x09,0x08,0x08,0x0C,0x0E,0x00, // -Z- 0x00,0x00,0xFC,0xFC,0x04,0x04,0x00,0x00,0x00,0x00,0x0F,0x0F,0x08,0x08,0x00,0x00, // -[- 0x38,0x70,0xE0,0xC0,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x03,0x07,0x0E,0x00, // -\- 0x00,0x00,0x04,0x04,0xFC,0xFC,0x00,0x00,0x00,0x00,0x08,0x08,0x0F,0x0F,0x00,0x00, // -]- 0x08,0x0C,0x06,0x03,0x06,0x0C,0x08,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, // -^- 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20, // -_- 0x00,0x00,0x03,0x07,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, // -`- 0x00,0xA0,0xA0,0xA0,0xE0,0xC0,0x00,0x00,0x07,0x0F,0x08,0x08,0x07,0x0F,0x08,0x00, // -a- 0x04,0xFC,0xFC,0x20,0x60,0xC0,0x80,0x00,0x08,0x0F,0x07,0x08,0x08,0x0F,0x07,0x00, // -b- 0xC0,0xE0,0x20,0x20,0x20,0x60,0x40,0x00,0x07,0x0F,0x08,0x08,0x08,0x0C,0x04,0x00, // -c- 0x80,0xC0,0x60,0x24,0xFC,0xFC,0x00,0x00,0x07,0x0F,0x08,0x08,0x07,0x0F,0x08,0x00, // -d- 0xC0,0xE0,0xA0,0xA0,0xA0,0xE0,0xC0,0x00,0x07,0x0F,0x08,0x08,0x08,0x0C,0x04,0x00, // -e- 0x40,0xF8,0xFC,0x44,0x0C,0x18,0x00,0x00,0x08,0x0F,0x0F,0x08,0x00,0x00,0x00,0x00, // -f- 0xC0,0xE0,0x20,0x20,0xC0,0xE0,0x20,0x00,0x27,0x6F,0x48,0x48,0x7F,0x3F,0x00,0x00, // -g- 0x04,0xFC,0xFC,0x40,0x20,0xE0,0xC0,0x00,0x08,0x0F,0x0F,0x00,0x00,0x0F,0x0F,0x00, // -h- 0x00,0x00,0x20,0xEC,0xEC,0x00,0x00,0x00,0x00,0x00,0x08,0x0F,0x0F,0x08,0x00,0x00, // -i- 0x00,0x00,0x00,0x00,0x20,0xEC,0xEC,0x00,0x00,0x30,0x70,0x40,0x40,0x7F,0x3F,0x00, // -j- 0x04,0xFC,0xFC,0x80,0xC0,0x60,0x20,0x00,0x08,0x0F,0x0F,0x01,0x03,0x0E,0x0C,0x00, // -k- 0x00,0x00,0x04,0xFC,0xFC,0x00,0x00,0x00,0x00,0x00,0x08,0x0F,0x0F,0x08,0x00,0x00, // -l- 0xE0,0xE0,0x60,0xC0,0x60,0xE0,0xC0,0x00,0x0F,0x0F,0x00,0x0F,0x00,0x0F,0x0F,0x00, // -m- 0x20,0xE0,0xC0,0x20,0x20,0xE0,0xC0,0x00,0x00,0x0F,0x0F,0x00,0x00,0x0F,0x0F,0x00, // -n- 0xC0,0xE0,0x20,0x20,0x20,0xE0,0xC0,0x00,0x07,0x0F,0x08,0x08,0x08,0x0F,0x07,0x00, // -o- 0x20,0xE0,0xC0,0x20,0x20,0xE0,0xC0,0x00,0x40,0x7F,0x7F,0x48,0x08,0x0F,0x07,0x00, // -p- 0xC0,0xE0,0x20,0x20,0xC0,0xE0,0x20,0x00,0x07,0x0F,0x08,0x48,0x7F,0x7F,0x40,0x00, // -q- 0x20,0xE0,0xC0,0x60,0x20,0x60,0xC0,0x00,0x08,0x0F,0x0F,0x08,0x00,0x00,0x00,0x00, // -r- 0x40,0xE0,0xA0,0x20,0x20,0x60,0x40,0x00,0x04,0x0C,0x09,0x09,0x0B,0x0E,0x04,0x00, // -s- 0x20,0x20,0xF8,0xFC,0x20,0x20,0x00,0x00,0x00,0x00,0x07,0x0F,0x08,0x0C,0x04,0x00, // -t- 0xE0,0xE0,0x00,0x00,0xE0,0xE0,0x00,0x00,0x07,0x0F,0x08,0x08,0x07,0x0F,0x08,0x00, // -u- 0x00,0xE0,0xE0,0x00,0x00,0xE0,0xE0,0x00,0x00,0x03,0x07,0x0C,0x0C,0x07,0x03,0x00, // -v- 0xE0,0xE0,0x00,0x00,0x00,0xE0,0xE0,0x00,0x07,0x0F,0x0C,0x07,0x0C,0x0F,0x07,0x00, // -w- 0x20,0x60,0xC0,0x80,0xC0,0x60,0x20,0x00,0x08,0x0C,0x07,0x03,0x07,0x0C,0x08,0x00, // -x- 0xE0,0xE0,0x00,0x00,0x00,0xE0,0xE0,0x00,0x47,0x4F,0x48,0x48,0x68,0x3F,0x1F,0x00, // -y- 0x60,0x60,0x20,0xA0,0xE0,0x60,0x20,0x00,0x0C,0x0E,0x0B,0x09,0x08,0x0C,0x0C,0x00, // -z- 0x00,0x40,0x40,0xF8,0xBC,0x04,0x04,0x00,0x00,0x00,0x00,0x07,0x0F,0x08,0x08,0x00, // -{- 0x00,0x00,0x00,0xBC,0xBC,0x00,0x00,0x00,0x00,0x00,0x00,0x0F,0x0F,0x00,0x00,0x00, // -|- 0x00,0x04,0x04,0xBC,0xF8,0x40,0x40,0x00,0x00,0x08,0x08,0x0F,0x07,0x00,0x00,0x00, // -}- 0x08,0x0C,0x04,0x0C,0x08,0x0C,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, // -~- } ; #endif //Tab_Ascii_8x16_CALL1 //=======8x16======================================================================= //#ifdef Tab_Ascii_8x16_CALL2 // #ifdef Display_Num_8x16_CALL const PROGMEM uint8_t Tab_Ascii_8x162[95][16]={ //细体字形 /*-- 文字: --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, /*-- 文字: ! --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x00,0x00,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x33,0x30,0x00,0x00,0x00, /*-- 文字: " --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x10,0x0C,0x06,0x10,0x0C,0x06,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, /*-- 文字: # --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x40,0xC0,0x78,0x40,0xC0,0x78,0x40,0x00,0x04,0x3F,0x04,0x04,0x3F,0x04,0x04,0x00, /*-- 文字: $ --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x70,0x88,0xFC,0x08,0x30,0x00,0x00,0x00,0x18,0x20,0xFF,0x21,0x1E,0x00,0x00, /*-- 文字: % --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0xF0,0x08,0xF0,0x00,0xE0,0x18,0x00,0x00,0x00,0x21,0x1C,0x03,0x1E,0x21,0x1E,0x00, /*-- 文字: & --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0xF0,0x08,0x88,0x70,0x00,0x00,0x00,0x1E,0x21,0x23,0x24,0x19,0x27,0x21,0x10, /*-- 文字: ' --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x10,0x16,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, /*-- 文字: ( --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x00,0x00,0xE0,0x18,0x04,0x02,0x00,0x00,0x00,0x00,0x07,0x18,0x20,0x40,0x00, /*-- 文字: ) --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x02,0x04,0x18,0xE0,0x00,0x00,0x00,0x00,0x40,0x20,0x18,0x07,0x00,0x00,0x00, /*-- 文字: * --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x40,0x40,0x80,0xF0,0x80,0x40,0x40,0x00,0x02,0x02,0x01,0x0F,0x01,0x02,0x02,0x00, /*-- 文字: + --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x00,0x00,0xF0,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x1F,0x01,0x01,0x01,0x00, /*-- 文字: , --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0xB0,0x70,0x00,0x00,0x00,0x00,0x00, /*-- 文字: - --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x01, /*-- 文字: . --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00, /*-- 文字: / --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x00,0x00,0x00,0x80,0x60,0x18,0x04,0x00,0x60,0x18,0x06,0x01,0x00,0x00,0x00, /*-- 文字: 0 --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x0F,0x10,0x20,0x20,0x10,0x0F,0x00, /*-- 文字: 1 --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00, /*-- 文字: 2 --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x70,0x08,0x08,0x08,0x88,0x70,0x00,0x00,0x30,0x28,0x24,0x22,0x21,0x30,0x00, /*-- 文字: 3 --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x30,0x08,0x88,0x88,0x48,0x30,0x00,0x00,0x18,0x20,0x20,0x20,0x11,0x0E,0x00, /*-- 文字: 4 --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x00,0xC0,0x20,0x10,0xF8,0x00,0x00,0x00,0x07,0x04,0x24,0x24,0x3F,0x24,0x00, /*-- 文字: 5 --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0xF8,0x08,0x88,0x88,0x08,0x08,0x00,0x00,0x19,0x21,0x20,0x20,0x11,0x0E,0x00, /*-- 文字: 6 --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0xE0,0x10,0x88,0x88,0x18,0x00,0x00,0x00,0x0F,0x11,0x20,0x20,0x11,0x0E,0x00, /*-- 文字: 7 --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x38,0x08,0x08,0xC8,0x38,0x08,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0x00, /*-- 文字: 8 --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x70,0x88,0x08,0x08,0x88,0x70,0x00,0x00,0x1C,0x22,0x21,0x21,0x22,0x1C,0x00, /*-- 文字: 9 --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x00,0x31,0x22,0x22,0x11,0x0F,0x00, /*-- 文字: : --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x00,0x00,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00, /*-- 文字: ; --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x60,0x00,0x00,0x00,0x00, /*-- 文字: < --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x00,0x80,0x40,0x20,0x10,0x08,0x00,0x00,0x01,0x02,0x04,0x08,0x10,0x20,0x00, /*-- 文字: = --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x00,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x00, /*-- 文字: > --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x08,0x10,0x20,0x40,0x80,0x00,0x00,0x00,0x20,0x10,0x08,0x04,0x02,0x01,0x00, /*-- 文字: ? --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x70,0x48,0x08,0x08,0x08,0xF0,0x00,0x00,0x00,0x00,0x30,0x36,0x01,0x00,0x00, /*-- 文字: @ --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0xC0,0x30,0xC8,0x28,0xE8,0x10,0xE0,0x00,0x07,0x18,0x27,0x24,0x23,0x14,0x0B,0x00, /*-- 文字: A --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x00,0xC0,0x38,0xE0,0x00,0x00,0x00,0x20,0x3C,0x23,0x02,0x02,0x27,0x38,0x20, /*-- 文字: B --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x08,0xF8,0x88,0x88,0x88,0x70,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x11,0x0E,0x00, /*-- 文字: C --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0xC0,0x30,0x08,0x08,0x08,0x08,0x38,0x00,0x07,0x18,0x20,0x20,0x20,0x10,0x08,0x00, /*-- 文字: D --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x08,0xF8,0x08,0x08,0x08,0x10,0xE0,0x00,0x20,0x3F,0x20,0x20,0x20,0x10,0x0F,0x00, /*-- 文字: E --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x20,0x23,0x20,0x18,0x00, /*-- 文字: F --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x00,0x03,0x00,0x00,0x00, /*-- 文字: G --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0xC0,0x30,0x08,0x08,0x08,0x38,0x00,0x00,0x07,0x18,0x20,0x20,0x22,0x1E,0x02,0x00, /*-- 文字: H --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x20,0x3F,0x21,0x01,0x01,0x21,0x3F,0x20, /*-- 文字: I --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00, /*-- 文字: J --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,0x00, /*-- 文字: K --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x08,0xF8,0x88,0xC0,0x28,0x18,0x08,0x00,0x20,0x3F,0x20,0x01,0x26,0x38,0x20,0x00, /*-- 文字: L --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x08,0xF8,0x08,0x00,0x00,0x00,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x20,0x30,0x00, /*-- 文字: M --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x08,0xF8,0xF8,0x00,0xF8,0xF8,0x08,0x00,0x20,0x3F,0x00,0x3F,0x00,0x3F,0x20,0x00, /*-- 文字: N --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x08,0xF8,0x30,0xC0,0x00,0x08,0xF8,0x08,0x20,0x3F,0x20,0x00,0x07,0x18,0x3F,0x00, /*-- 文字: O --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x10,0x20,0x20,0x20,0x10,0x0F,0x00, /*-- 文字: P --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x08,0xF8,0x08,0x08,0x08,0x08,0xF0,0x00,0x20,0x3F,0x21,0x01,0x01,0x01,0x00,0x00, /*-- 文字: Q --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x18,0x24,0x24,0x38,0x50,0x4F,0x00, /*-- 文字: R --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x08,0xF8,0x88,0x88,0x88,0x88,0x70,0x00,0x20,0x3F,0x20,0x00,0x03,0x0C,0x30,0x20, /*-- 文字: S --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x70,0x88,0x08,0x08,0x08,0x38,0x00,0x00,0x38,0x20,0x21,0x21,0x22,0x1C,0x00, /*-- 文字: T --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x18,0x08,0x08,0xF8,0x08,0x08,0x18,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00, /*-- 文字: U --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00, /*-- 文字: V --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x08,0x78,0x88,0x00,0x00,0xC8,0x38,0x08,0x00,0x00,0x07,0x38,0x0E,0x01,0x00,0x00, /*-- 文字: W --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0xF8,0x08,0x00,0xF8,0x00,0x08,0xF8,0x00,0x03,0x3C,0x07,0x00,0x07,0x3C,0x03,0x00, /*-- 文字: X --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x08,0x18,0x68,0x80,0x80,0x68,0x18,0x08,0x20,0x30,0x2C,0x03,0x03,0x2C,0x30,0x20, /*-- 文字: Y --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x08,0x38,0xC8,0x00,0xC8,0x38,0x08,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00, /*-- 文字: Z --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x10,0x08,0x08,0x08,0xC8,0x38,0x08,0x00,0x20,0x38,0x26,0x21,0x20,0x20,0x18,0x00, /*-- 文字: [ --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x00,0x00,0xFE,0x02,0x02,0x02,0x00,0x00,0x00,0x00,0x7F,0x40,0x40,0x40,0x00, /*-- 文字: \ --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x0C,0x30,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x06,0x38,0xC0,0x00, /*-- 文字: ] --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x02,0x02,0x02,0xFE,0x00,0x00,0x00,0x00,0x40,0x40,0x40,0x7F,0x00,0x00,0x00, /*-- 文字: ^ --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x00,0x04,0x02,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, /*-- 文字: _ --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80, /*-- 文字: ` --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, /*-- 文字: a --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x19,0x24,0x22,0x22,0x22,0x3F,0x20, /*-- 文字: b --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x08,0xF8,0x00,0x80,0x80,0x00,0x00,0x00,0x00,0x3F,0x11,0x20,0x20,0x11,0x0E,0x00, /*-- 文字: c --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x00,0x00,0x80,0x80,0x80,0x00,0x00,0x00,0x0E,0x11,0x20,0x20,0x20,0x11,0x00, /*-- 文字: d --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x00,0x00,0x80,0x80,0x88,0xF8,0x00,0x00,0x0E,0x11,0x20,0x20,0x10,0x3F,0x20, /*-- 文字: e --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x22,0x22,0x22,0x22,0x13,0x00, /*-- 文字: f --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x80,0x80,0xF0,0x88,0x88,0x88,0x18,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00, /*-- 文字: g --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x6B,0x94,0x94,0x94,0x93,0x60,0x00, /*-- 文字: h --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x08,0xF8,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20, /*-- 文字: i --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x80,0x98,0x98,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00, /*-- 文字: j --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x00,0x00,0x80,0x98,0x98,0x00,0x00,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00, /*-- 文字: k --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x08,0xF8,0x00,0x00,0x80,0x80,0x80,0x00,0x20,0x3F,0x24,0x02,0x2D,0x30,0x20,0x00, /*-- 文字: l --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x08,0x08,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00, /*-- 文字: m --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x20,0x3F,0x20,0x00,0x3F,0x20,0x00,0x3F, /*-- 文字: n --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20, /*-- 文字: o --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00, /*-- 文字: p --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x80,0x80,0x00,0x80,0x80,0x00,0x00,0x00,0x80,0xFF,0xA1,0x20,0x20,0x11,0x0E,0x00, /*-- 文字: q --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x0E,0x11,0x20,0x20,0xA0,0xFF,0x80, /*-- 文字: r --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x80,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x20,0x20,0x3F,0x21,0x20,0x00,0x01,0x00, /*-- 文字: s --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x33,0x24,0x24,0x24,0x24,0x19,0x00, /*-- 文字: t --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x80,0x80,0xE0,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x1F,0x20,0x20,0x00,0x00, /*-- 文字: u --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x80,0x80,0x00,0x00,0x00,0x80,0x80,0x00,0x00,0x1F,0x20,0x20,0x20,0x10,0x3F,0x20, /*-- 文字: v --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x00,0x01,0x0E,0x30,0x08,0x06,0x01,0x00, /*-- 文字: w --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x80,0x80,0x00,0x80,0x00,0x80,0x80,0x80,0x0F,0x30,0x0C,0x03,0x0C,0x30,0x0F,0x00, /*-- 文字: x --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x31,0x2E,0x0E,0x31,0x20,0x00, /*-- 文字: y --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x80,0x81,0x8E,0x70,0x18,0x06,0x01,0x00, /*-- 文字: z --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x21,0x30,0x2C,0x22,0x21,0x30,0x00, /*-- 文字: { --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x00,0x00,0x00,0x80,0x7C,0x02,0x02,0x00,0x00,0x00,0x00,0x00,0x3F,0x40,0x40, /*-- 文字: | --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00, /*-- 文字: } --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x02,0x02,0x7C,0x80,0x00,0x00,0x00,0x00,0x40,0x40,0x3F,0x00,0x00,0x00,0x00, /*-- 文字: ~ --*/ /*-- Comic Sans MS12; 此字体下对应的点阵为：宽x高=8x16 --*/ 0x00,0x06,0x01,0x01,0x02,0x02,0x04,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00 }; ///#endif //#endif //Tab_Ascii_8x16_CALL1 //=======5x7======================================================================= //#ifdef Tab_Ascii_5x7_CALL const PROGMEM uint8_t Tab_Ascii_5x71[95][5]={ /*全体ASCII 列表:5x7点阵*/ 0x00,0x00,0x00,0x00,0x00,//space 0x00,0x00,0x4f,0x00,0x00,//! 0x00,0x07,0x00,0x07,0x00,//" 0x14,0x7f,0x14,0x7f,0x14,//# 0x24,0x2a,0x7f,0x2a,0x12,//$ 0x23,0x13,0x08,0x64,0x62,//% 0x36,0x49,0x55,0x22,0x50,//& 0x00,0x05,0x07,0x00,0x00,//] 0x00,0x1c,0x22,0x41,0x00,//( 0x00,0x41,0x22,0x1c,0x00,//) 0x14,0x08,0x3e,0x08,0x14,//* 0x08,0x08,0x3e,0x08,0x08,//+ 0x00,0x50,0x30,0x00,0x00,//, 0x08,0x08,0x08,0x08,0x08,//- 0x00,0x60,0x60,0x00,0x00,//. 0x20,0x10,0x08,0x04,0x02,/// 0x3e,0x51,0x49,0x45,0x3e,//0 0x00,0x42,0x7f,0x40,0x00,//1 0x42,0x61,0x51,0x49,0x46,//2 0x21,0x41,0x45,0x4b,0x31,//3 0x18,0x14,0x12,0x7f,0x10,//4 0x27,0x45,0x45,0x45,0x39,//5 0x3c,0x4a,0x49,0x49,0x30,//6 0x01,0x71,0x09,0x05,0x03,//7 0x36,0x49,0x49,0x49,0x36,//8 0x06,0x49,0x49,0x29,0x1e,//9 0x00,0x36,0x36,0x00,0x00,//: 0x00,0x56,0x36,0x00,0x00,//; 0x08,0x14,0x22,0x41,0x00,//< 0x14,0x14,0x14,0x14,0x14,//= 0x00,0x41,0x22,0x14,0x08,//> 0x02,0x01,0x51,0x09,0x06,//? 0x32,0x49,0x79,0x41,0x3e,//@ 0x7e,0x11,0x11,0x11,0x7e,//A 0x7f,0x49,0x49,0x49,0x36,//B 0x3e,0x41,0x41,0x41,0x22,//C 0x7f,0x41,0x41,0x22,0x1c,//D 0x7f,0x49,0x49,0x49,0x41,//E 0x7f,0x09,0x09,0x09,0x01,//F 0x3e,0x41,0x49,0x49,0x7a,//G 0x7f,0x08,0x08,0x08,0x7f,//H 0x00,0x41,0x7f,0x41,0x00,//I 0x20,0x40,0x41,0x3f,0x01,//J 0x7f,0x08,0x14,0x22,0x41,//K 0x7f,0x40,0x40,0x40,0x40,//L 0x7f,0x02,0x0c,0x02,0x7f,//M 0x7f,0x04,0x08,0x10,0x7f,//N 0x3e,0x41,0x41,0x41,0x3e,//O 0x7f,0x09,0x09,0x09,0x06,//P 0x3e,0x41,0x51,0x21,0x5e,//Q 0x7f,0x09,0x19,0x29,0x46,//R 0x46,0x49,0x49,0x49,0x31,//S 0x01,0x01,0x7f,0x01,0x01,//T 0x3f,0x40,0x40,0x40,0x3f,//U 0x1f,0x20,0x40,0x20,0x1f,//V 0x3f,0x40,0x38,0x40,0x3f,//W 0x63,0x14,0x08,0x14,0x63,//X 0x07,0x08,0x70,0x08,0x07,//Y 0x61,0x51,0x49,0x45,0x43,//Z 0x00,0x7f,0x41,0x41,0x00,//[ 0x02,0x04,0x08,0x10,0x20,//\ 0x00,0x41,0x41,0x7f,0x00,//] 0x04,0x02,0x01,0x02,0x04,//^ 0x40,0x40,0x40,0x40,0x40,//_ 0x01,0x02,0x04,0x00,0x00,//` 0x20,0x54,0x54,0x54,0x78,//a 0x7f,0x48,0x48,0x48,0x30,//b 0x38,0x44,0x44,0x44,0x44,//c 0x30,0x48,0x48,0x48,0x7f,//d 0x38,0x54,0x54,0x54,0x58,//e 0x00,0x08,0x7e,0x09,0x02,//f 0x48,0x54,0x54,0x54,0x3c,//g 0x7f,0x08,0x08,0x08,0x70,//h 0x00,0x00,0x7a,0x00,0x00,//i 0x20,0x40,0x40,0x3d,0x00,//j 0x7f,0x20,0x28,0x44,0x00,//k 0x00,0x41,0x7f,0x40,0x00,//l 0x7c,0x04,0x38,0x04,0x7c,//m 0x7c,0x08,0x04,0x04,0x78,//n 0x38,0x44,0x44,0x44,0x38,//o 0x7c,0x14,0x14,0x14,0x08,//p 0x08,0x14,0x14,0x14,0x7c,//q 0x7c,0x08,0x04,0x04,0x08,//r 0x48,0x54,0x54,0x54,0x24,//s 0x04,0x04,0x3f,0x44,0x24,//t 0x3c,0x40,0x40,0x40,0x3c,//u 0x1c,0x20,0x40,0x20,0x1c,//v 0x3c,0x40,0x30,0x40,0x3c,//w 0x44,0x28,0x10,0x28,0x44,//x 0x04,0x48,0x30,0x08,0x04,//y 0x44,0x64,0x54,0x4c,0x44,//z 0x08,0x36,0x41,0x41,0x00,//{ 0x00,0x00,0x77,0x00,0x00,//| 0x00,0x41,0x41,0x36,0x08,//} 0x04,0x02,0x02,0x02,0x01,//~ }; //#endif //Tab_Ascii_5x7_CALL uint8 zhuang1[]={ /*-- 文字: 状 --*/ /*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/ 0x08,0x30,0x00,0xFF,0x20,0x20,0x20,0x20,0xFF,0x20,0xE1,0x26,0x2C,0x20,0x20,0x00, 0x04,0x02,0x01,0xFF,0x40,0x20,0x18,0x07,0x00,0x00,0x03,0x0C,0x30,0x60,0x20,0x00 }; uint8 tai1[]={ /*-- 文字: 态 --*/ /*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/ 0x00,0x04,0x04,0x04,0x84,0x44,0x34,0x4F,0x94,0x24,0x44,0x84,0x84,0x04,0x00,0x00, 0x00,0x60,0x39,0x01,0x00,0x3C,0x40,0x42,0x4C,0x40,0x40,0x70,0x04,0x09,0x31,0x00 }; uint8 shi1[]={ /*-- 文字: 使 --*/ /*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/ 0x40,0x20,0xF0,0x1C,0x07,0xF2,0x94,0x94,0x94,0xFF,0x94,0x94,0x94,0xF4,0x04,0x00, 0x00,0x00,0x7F,0x00,0x40,0x41,0x22,0x14,0x0C,0x13,0x10,0x30,0x20,0x61,0x20,0x00 }; uint8 yong1[]={ /*-- 文字: 用 --*/ /*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/ 0x00,0x00,0x00,0xFE,0x22,0x22,0x22,0x22,0xFE,0x22,0x22,0x22,0x22,0xFE,0x00,0x00, 0x80,0x40,0x30,0x0F,0x02,0x02,0x02,0x02,0xFF,0x02,0x02,0x42,0x82,0x7F,0x00,0x00 }; //x=9 y=16 点阵 0-9 const PROGMEM uint8_t lcd_numbers_lit[]={ 0x00,0xE0,0xE0,0x60,0x20,0x60,0xE0,0xE0,0x00,//0 0x00,0x7F,0x7F,0x60,0x40,0x60,0x7F,0x7F,0x00, 0x00,0x00,0x40,0x40,0xE0,0xE0,0x00,0x00,0x00,//1 0x00,0x00,0x00,0x00,0x7F,0x7F,0x00,0x00,0x00, 0x00,0xE0,0xE0,0x20,0x20,0xE0,0xE0,0xC0,0x00,//2 0x00,0x71,0x79,0x78,0x5E,0x47,0x43,0x41,0x00, 0x00,0xE0,0xE0,0x20,0x20,0xE0,0xE0,0xC0,0x00,//3 0x00,0x78,0x78,0x42,0x47,0x7F,0x7D,0x39,0x00, 0x00,0x00,0x00,0x80,0xE0,0xE0,0xE0,0x00,0x00,//4 0x00,0x0E,0x0F,0x0B,0x7F,0x7F,0x7F,0x08,0x00, 0x00,0xE0,0xE0,0xE0,0x20,0x20,0x20,0x20,0x00,//5 0x00,0x73,0x73,0x43,0x41,0x7F,0x7F,0x3E,0x00, 0x00,0xE0,0xE0,0x60,0x20,0x60,0x60,0x60,0x00,//6 0x00,0x7F,0x7F,0x43,0x43,0x7F,0x7E,0x3C,0x00, 0x00,0x20,0x20,0x20,0xA0,0xE0,0xE0,0x60,0x00,//7 0x00,0x00,0x40,0x78,0x7F,0x0F,0x01,0x00,0x00, 0x00,0xE0,0xE0,0x20,0x20,0x20,0xE0,0xE0,0x00,//8 0x00,0x7D,0x7D,0x47,0x42,0x47,0x7D,0x7D,0x00, 0x00,0xE0,0xE0,0x20,0x20,0xE0,0xE0,0x80,0x00,//9 0x00,0x67,0x6F,0x4C,0x6C,0x7F,0x3F,0x0F,0x00 }; //x=12 y=16 点阵 0-9数字 const PROGMEM uint8_t lcd_numbers[]={ 0x00,0xF0,0xFC,0xFC,0x0E,0x02,0x02,0x0E,0xFC,0xFC,0xF0,0x00,//0 0x00,0x07,0x3F,0x3F,0x70,0x40,0x40,0x70,0x3F,0x3F,0x07,0x00, 0x00,0x00,0x00,0x08,0x08,0xFC,0xFE,0xFE,0x00,0x00,0x00,0x00,//1 0x00,0x00,0x00,0x00,0x00,0x7F,0x7F,0x7F,0x00,0x00,0x00,0x00, 0x00,0x38,0x3C,0x3E,0x06,0x02,0x86,0xFE,0xFC,0x78,0x00,0x00,//2 0x00,0x60,0x78,0x7C,0x5E,0x4F,0x43,0x41,0x40,0x40,0x00,0x00, 0x00,0x18,0x1C,0x1E,0x86,0x82,0xC6,0xFE,0x7C,0x38,0x00,0x00,//3 0x00,0x1C,0x3C,0x7C,0x60,0x40,0x61,0x7F,0x3F,0x1E,0x00,0x00, 0x00,0x00,0x80,0xC0,0xF0,0x3C,0xFE,0xFE,0xFE,0x00,0x00,0x00,//4 0x00,0x06,0x07,0x05,0x04,0x04,0x7F,0x7F,0x7F,0x04,0x04,0x00, 0x00,0x00,0xFE,0xFE,0xFE,0x62,0x62,0xE2,0xE2,0x82,0x00,0x00,//5 0x00,0x18,0x38,0x78,0x60,0x40,0x60,0x7F,0x3F,0x1F,0x00,0x00, 0x00,0xF0,0xFC,0xFC,0xCE,0x42,0xC6,0xCE,0x8E,0x0C,0x00,0x00,//6 0x00,0x0F,0x3F,0x7F,0x60,0x40,0x60,0x7F,0x3F,0x1F,0x00,0x00, 0x00,0x02,0x02,0x02,0x02,0x82,0xF2,0xFE,0x7E,0x0E,0x00,0x00,//7 0x00,0x00,0x00,0x60,0x7C,0x7F,0x1F,0x03,0x00,0x00,0x00,0x00, 0x00,0x38,0x7C,0x7E,0xC6,0x82,0x82,0xC6,0x7E,0x7C,0x38,0x00,//8 0x00,0x1E,0x3F,0x7F,0x61,0x40,0x40,0x61,0x7F,0x3F,0x1E,0x00, 0x00,0xF8,0xFC,0xFE,0x06,0x02,0x06,0xFE,0xFC,0xF0,0x00,0x00,//9 0x00,0x30,0x71,0x73,0x63,0x42,0x73,0x3F,0x1F,0x07,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//. 0x00,0x00,0x00,0x38,0x38,0x38,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,//- 0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x00 }; const PROGMEM uint8_t Tab_Ascii_5x72[95][5]={ /*全体ASCII 列表:5x7点阵*/ 0x00,0x00,0x00,0x00,0x00,//space 0x00,0x00,0x4f,0x00,0x00,//! 0x00,0x07,0x00,0x07,0x00,//" 0x14,0x7f,0x14,0x7f,0x14,//# 0x24,0x2a,0x7f,0x2a,0x12,//$ 0x23,0x13,0x08,0x64,0x62,//% 0x36,0x49,0x55,0x22,0x50,//& 0x00,0x05,0x07,0x00,0x00,//] 0x00,0x1c,0x22,0x41,0x00,//( 0x00,0x41,0x22,0x1c,0x00,//) 0x14,0x08,0x3e,0x08,0x14,//* 0x08,0x08,0x3e,0x08,0x08,//+ 0x00,0x50,0x30,0x00,0x00,//, 0x08,0x08,0x08,0x08,0x08,//- 0x00,0x60,0x60,0x00,0x00,//. 0x20,0x10,0x08,0x04,0x02,/// 0x3e,0x51,0x49,0x45,0x3e,//0 0x00,0x42,0x7f,0x40,0x00,//1 0x42,0x61,0x51,0x49,0x46,//2 0x21,0x41,0x45,0x4b,0x31,//3 0x18,0x14,0x12,0x7f,0x10,//4 0x27,0x45,0x45,0x45,0x39,//5 0x3c,0x4a,0x49,0x49,0x30,//6 0x01,0x71,0x09,0x05,0x03,//7 0x36,0x49,0x49,0x49,0x36,//8 0x06,0x49,0x49,0x29,0x1e,//9 0x00,0x36,0x36,0x00,0x00,//: 0x00,0x56,0x36,0x00,0x00,//; 0x08,0x14,0x22,0x41,0x00,//< 0x14,0x14,0x14,0x14,0x14,//= 0x00,0x41,0x22,0x14,0x08,//> 0x02,0x01,0x51,0x09,0x06,//? 0x32,0x49,0x79,0x41,0x3e,//@ 0x7e,0x11,0x11,0x11,0x7e,//A 0x7f,0x49,0x49,0x49,0x36,//B 0x3e,0x41,0x41,0x41,0x22,//C 0x7f,0x41,0x41,0x22,0x1c,//D 0x7f,0x49,0x49,0x49,0x41,//E 0x7f,0x09,0x09,0x09,0x01,//F 0x3e,0x41,0x49,0x49,0x7a,//G 0x7f,0x08,0x08,0x08,0x7f,//H 0x00,0x41,0x7f,0x41,0x00,//I 0x20,0x40,0x41,0x3f,0x01,//J 0x7f,0x08,0x14,0x22,0x41,//K 0x7f,0x40,0x40,0x40,0x40,//L 0x7f,0x02,0x0c,0x02,0x7f,//M 0x7f,0x04,0x08,0x10,0x7f,//N 0x3e,0x41,0x41,0x41,0x3e,//O 0x7f,0x09,0x09,0x09,0x06,//P 0x3e,0x41,0x51,0x21,0x5e,//Q 0x7f,0x09,0x19,0x29,0x46,//R 0x46,0x49,0x49,0x49,0x31,//S 0x01,0x01,0x7f,0x01,0x01,//T 0x3f,0x40,0x40,0x40,0x3f,//U 0x1f,0x20,0x40,0x20,0x1f,//V 0x3f,0x40,0x38,0x40,0x3f,//W 0x63,0x14,0x08,0x14,0x63,//X 0x07,0x08,0x70,0x08,0x07,//Y 0x61,0x51,0x49,0x45,0x43,//Z 0x00,0x7f,0x41,0x41,0x00,//[ 0x02,0x04,0x08,0x10,0x20,// 0x00,0x41,0x41,0x7f,0x00,//] 0x04,0x02,0x01,0x02,0x04,//^ 0x40,0x40,0x40,0x40,0x40,//_ 0x01,0x02,0x04,0x00,0x00,//` 0x20,0x54,0x54,0x54,0x78,//a 0x7f,0x48,0x48,0x48,0x30,//b 0x38,0x44,0x44,0x44,0x44,//c 0x30,0x48,0x48,0x48,0x7f,//d 0x38,0x54,0x54,0x54,0x58,//e 0x00,0x08,0x7e,0x09,0x02,//f 0x48,0x54,0x54,0x54,0x3c,//g 0x7f,0x08,0x08,0x08,0x70,//h 0x00,0x00,0x7a,0x00,0x00,//i 0x20,0x40,0x40,0x3d,0x00,//j 0x7f,0x20,0x28,0x44,0x00,//k 0x00,0x41,0x7f,0x40,0x00,//l 0x7c,0x04,0x38,0x04,0x7c,//m 0x7c,0x08,0x04,0x04,0x78,//n 0x38,0x44,0x44,0x44,0x38,//o 0x7c,0x14,0x14,0x14,0x08,//p 0x08,0x14,0x14,0x14,0x7c,//q 0x7c,0x08,0x04,0x04,0x08,//r 0x48,0x54,0x54,0x54,0x24,//s 0x04,0x04,0x3f,0x44,0x24,//t 0x3c,0x40,0x40,0x40,0x3c,//u 0x1c,0x20,0x40,0x20,0x1c,//v 0x3c,0x40,0x30,0x40,0x3c,//w 0x44,0x28,0x10,0x28,0x44,//x 0x04,0x48,0x30,0x08,0x04,//y 0x44,0x64,0x54,0x4c,0x44,//z 0x08,0x36,0x41,0x41,0x00,//{ 0x00,0x00,0x77,0x00,0x00,//| 0x00,0x41,0x41,0x36,0x08,//} 0x04,0x02,0x02,0x02,0x01,//~ }; /////////////// #define Start_T1 TCCR1B|=_BV(CS11);TCNT1=0//复位预计分频器并开启定时器T1 #define Stop_T1 TCCR1B&=~_BV(CS11) //关闭定时器T1 //数码管的段码编码 unsigned char table[10] = {0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f,0x6f}; volatile unsigned char i,j,k; volatile unsigned char IRcode; //定义一个长度为4字节的无符号long类型变量来存储代码 volatile unsigned char IR_OK=0; //IR信号接收有效当程序响应接收以后请马上清零这样才会继续接收下一IR码 volatile unsigned char IR_con=0; //IR信号当前接收位 0时表示第0位即同步码(4.5ms高电平) volatile unsigned int Pulse_length=0; //捕获的脉冲宽度 volatile unsigned char ICP_Parity=0; //捕获中断奇偶次计数 1时为偶次并在此时判断脉宽 volatile unsigned char address; volatile unsigned char code_data; volatile unsigned char code_data1; unsigned char clrbit; #define FREQ 8 //定义单片机工作频率为 4M /////////////// //**************************************************************** // 函数名称：DelayLcd // 函数功能：延时 // 入口参数： // 出口参数： //***************************************************************** void DelayLcd(uint16 i) { uint16 j; for(j=200;j>0;j--) for(;i>0;i--); //while(i--); } //**************************************************************** // 函数名称：LcdWriteCommand // 函数功能：写指令到LCD模块 // 入口参数：数据 // 出口参数： //***************************************************************** void LcdWriteCommand(uint8 data1) // { uint8 i ; P_LCDCS0 ; P_LCDRS0 ; for(i=8;i>0;i--) { P_LCDCLK0; if(data1&0x80) P_LCDDAT1; else P_LCDDAT0; P_LCDCLK1; data1 <<= 1; } } //**************************************************************** // 函数名称：LcdWritedata // 函数功能：写数据到LCD模块 // 入口参数：数据 // 出口参数： //***************************************************************** void LcdWritedata(uint8 data1) // { uint8 i; P_LCDCS0 ; P_LCDRS1 ; for(i=8;i>0;i--) { P_LCDCLK0; if(data1&0x80) P_LCDDAT1; else P_LCDDAT0; P_LCDCLK1; data1 <<= 1; } } //**************************************************************** // 函数名称：Lcd_SetAddr // 函数功能：设置LCD显示地址 // 入口参数：页地址列地址 // 出口参数： //***************************************************************** void Lcd_SetAddr(uint8 page,uint8 column) { //LcdWriteCommand(0xb0 | (y+yy)); //LcdWriteCommand(0x10 | (x>>4)); //LcdWriteCommand(0x00 | (x&0x0f)); //P_LCDCS0 ; LcdWriteCommand(0xb0|page); /*设置页地址*/ LcdWriteCommand((column>>4)|0x10); /*设置列地址的高4位*/ LcdWriteCommand(column&0x0f); /*设置列地址的低4位*/ } ////// void Display_Graphic_32x2(uint8 page,uint8 column,PROGMEM uint8_t *dp) // 电池显示 0、2、4、6、8、10 { uint8 i,j; uint8 page_address; uint8 column_address_L,column_address_H; page_address = 0xb0|page; column_address_L =(column&0x0f); column_address_H =(column>>4)|0x10; P_LCDCS0 ; for(j=0;j<2;j++) { LcdWriteCommand(page_address+j); /*设置页地址*/ LcdWriteCommand(column_address_H); /*设置列地址的高4位*/ LcdWriteCommand(column_address_L); /*设置列地址的低4位*/ for (i=32;i>0;i--) //写32行 { LcdWritedata(pgm_read_byte(dp++)); /*写数据到LCD,每写完一个8位的数据后列地址自动加1*/ } LcdWritedata(0x00); } P_LCDCS1 ; } //#ifdef Display_Graphic_32x32_CALL void Display_Graphic_32x32(uint8 page,uint8 column,PROGMEM uint8_t *dp) { uint8 i,j; uint8 page_address; uint8 column_address_L,column_address_H; page_address = 0xb0|page; column_address_L =(column&0x0f); column_address_H =(column>>4)|0x10; P_LCDCS0 ; &

标签： 程序

上传时间： 2016-03-03

上传用户：彦 yan
12345

/****************temic*********t5557***********************************/ #include <at892051.h> #include <string.h> #include <intrins.h> #include <stdio.h> #define uchar unsigned char #define uint unsigned int #define ulong unsigned long //STC12C2051AD的SFR定义 sfr WDT_CONTR = 0xe1;//stc2051的看门狗?????? /**********全局常量************/ //写卡的命令 #define write_command0 0//写密码 #define write_command1 1//写配置字 #define write_command2 2//密码写数据 #define write_command3 3//唤醒 #define write_command4 4//停止命令 #define TRUE 1 #define FALSE 0 #define OK 0 #define ERROR 255 //读卡的时间参数us #define ts_min 250//270*11.0592/12=249//取近似的整数 #define ts_max 304//330*11.0592/12=304 #define t1_min 73//90*11.0592/12=83:-10调整 #define t1_max 156//180*11.0592/12=166 #define t2_min 184//210*11.0592/12=194 #define t2_max 267//300*11.0592/12=276 //***********不采用中断处理:采用查询的方法读卡时关所有中断****************/ sbit p_U2270B_Standby = P3^5;//p_U2270B_Standby PIN=13 sbit p_U2270B_CFE = P3^3;//p_U2270B_CFE PIN=6 sbit p_U2270B_OutPut = P3^7;//p_U2270B_OutPut PIN=2 sbit wtd_sck = P1^7;//SPI总线 sbit wtd_si = P1^3; sbit wtd_so = P1^2; sbit iic_data = P1^2;//lcd IIC sbit iic_clk = P1^7; sbit led_light = P1^6;//测试绿灯 sbit led_light1 = P1^5;//测试红灯 sbit led_light_ok = P1^1;//读卡成功标志 sbit fengmingqi = P1^5; /***********全局变量************************************/ uchar data Nkey_a[4] = {0xA0, 0xA1, 0xA2, 0xA3};//初始密码 //uchar idata card_snr[4]; //配置字 uchar data bankdata[28] = {1,2,3,4,5,6,7,1,2,3,4,5,6,7,1,2,3,4,5,6,7,1,2,3,4,5,6,7}; //存储卡上用户数据(1-7)7*4=28 uchar data cominceptbuff[6] = {1,2,3,4,5,6};//串口接收数组ram uchar command; //第一个命令 uchar command1;// //uint temp; uchar j,i; uchar myaddr = 8; //uchar ywqz_count,time_count; //ywqz jishu: uchar bdata DATA; sbit BIT0 = DATA^0; sbit BIT1 = DATA^1; sbit BIT2 = DATA^2; sbit BIT3 = DATA^3; sbit BIT4 = DATA^4; sbit BIT5 = DATA^5; sbit BIT6 = DATA^6; sbit BIT7 = DATA^7; uchar bdata DATA1; sbit BIT10 = DATA1^0; sbit BIT11 = DATA1^1; sbit BIT12 = DATA1^2; sbit BIT13 = DATA1^3; sbit BIT14 = DATA1^4; sbit BIT15 = DATA1^5; sbit BIT16 = DATA1^6; sbit BIT17 = DATA1^7; bit i_CurrentLevel;//i_CurrentLevel BIT 00H(Saves current level of OutPut pin of U2270B) bit timer1_end; bit read_ok = 0; //缓存定时值,因用同一个定时器 union HLint { uint W; struct { uchar H;uchar L; } B; };//union HLint idata a union HLint data a; //缓存定时值,因用同一个定时器 union HLint0 { uint W; struct { uchar H; uchar L; } B; };//union HLint idata a union HLint0 data b; /**********************函数原型*****************/ //读写操作 void f_readcard(void);//全部读出1~7 AOR唤醒 void f_writecard(uchar x);//根据命令写不同的内容和操作 void f_clearpassword(void);//清除密码 void f_changepassword(void);//修改密码 //功能子函数 void write_password(uchar data *data p);//写初始密码或数据 void write_block(uchar x,uchar data *data p);//不能用通用指针 void write_bit(bit x);//写位 /*子函数区*****************************************************/ void delay_2(uint x) //延时,时间x*10us@12mhz,最小20us@12mhz { x--; x--; while(x) { _nop_(); _nop_(); x--; } _nop_();//WDT_CONTR=0X3C;不能频繁的复位 _nop_(); } ///////////////////////////////////////////////////////////////////// void initial(void) { SCON = 0x50; //串口方式1,允许接收 //SCON =0x50; //01010000B:10位异步收发,波特率可变,SM2=0不用接收到有效停止位才RI=1, //REN=1允许接收 TMOD = 0x21; //定时器1 定时方式2(8位),定时器0 定时方式1(16位) TCON = 0x40; //设定时器1 允许开始计时(IT1=1) TH1 = 0xfD; //FB 18.432MHz 9600 波特率 TL1 = 0xfD; //fd 11.0592 9600 IE = 0X90; //EA=ES=1 TR1 = 1; //启动定时器 WDT_CONTR = 0x3c;//使能看门狗 p_U2270B_Standby = 0;//单电源 PCON = 0x00; IP = 0x10;//uart you xian XXXPS PT1 PX1 PT0 PX0 led_light1 = 1; led_light = 0; p_U2270B_OutPut = 1; } /************************************************/ void f_readcard()//读卡 { EA = 0;//全关,防止影响跳变的定时器计时 WDT_CONTR = 0X3C;//喂狗 p_U2270B_CFE = 1;// delay_2(232); //>2.5ms /* // aor 用唤醒功能来防碰撞 p_U2270B_CFE = 0; delay_2(18);//start gap>150us write_bit(1);//10=操作码读0页 write_bit(0); write_password(&bankdata[24]);//密码block7 p_U2270B_CFE =1 ;// delay_2(516);//编程及确认时间5.6ms */ WDT_CONTR = 0X3C;//喂狗 led_light = 0; b.W = 0; while(!(read_ok == 1)) { //while(p_U2270B_OutPut);//等一个稳定的低电平?超时判断? while(!p_U2270B_OutPut);//等待上升沿的到来同步信号检测1 TR0 = 1; //deng xia jiang while(p_U2270B_OutPut);//等待下降沿 TR0 = 0; a.B.H = TH0; a.B.L = TL0; TH0 = TL0 = 0; TR0 = 1;//定时器晚启动10个周期 //同步头 if((324 < a.W) && (a.W < 353)) ;//检测同步信号1 else { TR0 = 0; TH0 = TL0 = 0; goto read_error; } //等待上升沿 while(!p_U2270B_OutPut); TR0 = 0; a.B.H = TH0; a.B.L = TL0; TH0 = TL0 = 0; TR0 = 1;//b.N1<<=8; if(a.B.L < 195);//0.5p else { TR0 = 0; TH0 = TL0 = 0; goto read_error; } //读0~7块的数据 for(j = 0;j < 28;j++) { //uchar i; for(i = 0;i < 16;i++)//8个位 { //等待下降沿的到来 while(p_U2270B_OutPut); TR0 = 0; a.B.H = TH0; a.B.L = TL0; TH0 = TL0 = 0; TR0 = 1; if(t2_max < a.W/*)&&(a.W < t2_max)*/)//1P { b.W >>= 2;//先左移再赋值 b.B.L += 0xc0; i++; } else if(t1_min < a.B.L/*)&&(a.B.L < t1_max)*/)//0.5p { b.W >>= 1; b.B.L += 0x80; } else { TR0 = 0; TH0 = TL0 = 0; goto read_error; } i++; while(!p_U2270B_OutPut);//上升 TR0 = 0; a.B.H = TH0; a.B.L = TL0; TH0 = TL0 = 0; TR0 = 1; if(t2_min < a.W/*)&&(a.W < t2_max)*/)//1P { b.W >>= 2; i++; } else if(t1_min < a.B.L/*a.W)&&(a.B.L < t1_max)*/)//0.5P //else if(!(a.W==0)) { b.W >>= 1; //temp+=0x00; //led_light1=0;led_light=1;delay_2(40000); } else { TR0 = 0; TH0 = TL0 = 0; goto read_error; } i++; } //取出奇位 DATA = b.B.L; BIT13 = BIT7; BIT12 = BIT5; BIT11 = BIT3; BIT10 = BIT1; DATA = b.B.H; BIT17 = BIT7; BIT16 = BIT5; BIT15 = BIT3; BIT14 = BIT1; bankdata[j] = DATA1; } read_ok = 1;//读卡完成了 read_error: _nop_(); } } /***************************************************/ void f_writecard(uchar x)//写卡 { p_U2270B_CFE = 1; delay_2(232); //>2.5ms //psw=0 standard write if (x == write_command0)//写密码:初始化密码 { uchar i; uchar data *data p; p = cominceptbuff; p_U2270B_CFE = 0; delay_2(31);//start gap>330us write_bit(1);//写操作码1:10 write_bit(0);//写操作码0 write_bit(0);//写锁定位0 for(i = 0;i < 35;i++) { write_bit(1);//写数据位1 } p_U2270B_CFE = 1; led_light1 = 0; led_light = 1; delay_2(40000);//测试使用 //write_block(cominceptbuff[4],p); p_U2270B_CFE = 1; bankdata[20] = cominceptbuff[0];//密码存入 bankdata[21] = cominceptbuff[1]; bankdata[22] = cominceptbuff[2]; bankdata[23] = cominceptbuff[3]; } else if (x == write_command1)//配置卡参数:初始化 { uchar data *data p; p = cominceptbuff; write_bit(1);//写操作码1:10 write_bit(0);//写操作码0 write_bit(0);//写锁定位0 write_block(cominceptbuff[4],p); p_U2270B_CFE= 1; } //psw=1 pssword mode else if(x == write_command2) //密码写数据 { uchar data*data p; p = &bankdata[24]; write_bit(1);//写操作码1:10 write_bit(0);//写操作码0 write_password(p);//发口令 write_bit(0);//写锁定位0 p = cominceptbuff; write_block(cominceptbuff[4],p);//写数据 } else if(x == write_command3)//aor //唤醒 { //cominceptbuff[1]操作码10 X xxxxxB uchar data *data p; p = cominceptbuff; write_bit(1);//10 write_bit(0); write_password(p);//密码 p_U2270B_CFE = 1;//此时数据不停的循环传出 } else //停止操作码 { write_bit(1);//11 write_bit(1); p_U2270B_CFE = 1; } p_U2270B_CFE = 1; delay_2(560);//5.6ms } /************************************/ void f_clearpassword()//清除密码 { uchar data *data p; uchar i,x; p = &bankdata[24];//原密码 p_U2270B_CFE = 0; delay_2(18);//start gap>150us //操作码10:10xxxxxxB write_bit(1); write_bit(0); for(x = 0;x < 4;x++)//发原密码 { DATA = *(p++); for(i = 0;i < 8;i++) { write_bit(BIT0); DATA >>= 1; } } write_bit(0);//锁定位0:0 p = &cominceptbuff[0]; write_block(0x00,p);//写新配置参数:pwd=0 //密码无效:即清除密码 DATA = 0x00;//停止操作码00000000B for(i = 0;i < 2;i++) { write_bit(BIT7); DATA <<= 1; } p_U2270B_CFE = 1; delay_2(560);//5.6ms } /*********************************/ void f_changepassword()//修改密码 { uchar data *data p; uchar i,x,addr; addr = 0x07;//block7 p = &Nkey_a[0];//原密码 DATA = 0x80;//操作码10:10xxxxxxB for(i = 0;i < 2;i++) { write_bit(BIT7); DATA <<= 1; } for(x = 0;x < 4;x++)//发原密码 { DATA = *(p++); for(i = 0;i < 8;i++) { write_bit(BIT7); DATA >>= 1; } } write_bit(0);//锁定位0:0 p = &cominceptbuff[0]; write_block(0x07,p);//写新密码 p_U2270B_CFE = 1; bankdata[24] = cominceptbuff[0];//密码存入 bankdata[25] = cominceptbuff[1]; bankdata[26] = cominceptbuff[2]; bankdata[27] = cominceptbuff[3]; DATA = 0x00;//停止操作码00000000B for(i = 0;i < 2;i++) { write_bit(BIT7); DATA <<= 1; } p_U2270B_CFE = 1; delay_2(560);//5.6ms } /***************************子函数***********************************/ void write_bit(bit x)//写一位 { if(x) { p_U2270B_CFE = 1; delay_2(32);//448*11.0592/120=42延时448us p_U2270B_CFE = 0; delay_2(28);//280*11.0592/120=26写1 } else { p_U2270B_CFE = 1; delay_2(92);//192*11.0592/120=18 p_U2270B_CFE = 0; delay_2(28);//280*11.0592/120=26写0 } } /*******************写一个block*******************/ void write_block(uchar addr,uchar data *data p) { uchar i,j; for(i = 0;i < 4;i++)//block0数据 { DATA = *(p++); for(j = 0;j < 8;j++) { write_bit(BIT0); DATA >>= 1; } } DATA = addr <<= 5;//0地址 for(i = 0;i < 3;i++) { write_bit(BIT7); DATA <<= 1; } } /*************************************************/ void write_password(uchar data *data p) { uchar i,j; for(i = 0;i < 4;i++)// { DATA = *(p++); for(j = 0;j < 8;j++) { write_bit(BIT0); DATA >>= 1; } } } /*************************************************/ void main() { initial(); TI = RI = 0; ES = 1; EA = 1; delay_2(28); //f_readcard(); while(1) { f_readcard(); //读卡 f_writecard(command1); //写卡 f_clearpassword(); //清除密码 f_changepassword(); //修改密码 } }

标签： 12345

上传时间： 2017-10-20

上传用户：my_lcs
VK36W8I SOP16/QFN16 八点/8通道水位检测感应电容式芯片

深圳永嘉微电超高性价比水位检测芯片推出 *水位检测芯片可用于需要检测水位，缺水，溢出等场合。适合应用于饮水机、净饮机、咖啡机、水壶、洗碗机、制冰机等水相关家用电器和电子产品。测试环境：在一个玻璃容器外壁（玻璃1-5毫米不等），通过双面电子导热硅胶，把水位检测PCB直接贴在玻璃上面检测水位。1-8点高灵敏度电容式水位检测专用触控IC-VK36W系列水位检测背景技术：目前的检水方式主要有探针检水、水位传感器检水(光电式水位传感器,超声波水位传感器)和干簧管检水等方式，但这些方式的应用成本高，并且其安装时需要用到很长的连接线路，为了配合长的连接线路，容易使得产品的结构受到限制，并且拆装复杂，价格昴贵，不利于产品的推广及普及广泛应用。技术实现要素：为解决上述问题，本实用新型的目的在于提供一种触摸感应检水电路，能够准确检测是否有水，并且能够降低电路的成本几个等级，简化检水的结构，使得拆装便利，有利于产品的生产。 VK36WXX系列（最多支持9个检测点）是一款用于一段液位检测的专用集成电路。基于电容感应的检测原理，集成我们公司花费多年研究的独特算法，能够做到智能识别，无论是有液体上电，还是无液体上电，都能正确指示液位状态。本产品既可适用于直接接触液体的检测装置，也可适用于不直接接触液体的检测装置。尤其是非接触式的检测更安全更方便、更有优势，也可防腐蚀、防污染 1.液体检测器 2.触摸开关 3.加温器 4.喷雾器 5 水池、水箱、水缸、液体皿联系人：许先生联系手机：188 9858 2398 （微信）联系QQ：191 888 5898 E-mail：zes1688@163.com

标签： 16 36W SOP QFN VK 36 8I W8 水位检测感应电容

上传时间： 2019-08-28

上传用户：szqxw1688
水位感应检测VK36W6D SOP16/QFN16电容式高灵敏液体探测检测IC

深圳永嘉微电超高性价比水位检测芯片推出水位检测芯片可用于需要检测水位，缺水，溢出等场合。适合应用于饮水机、净饮机、咖啡机、水壶、洗碗机、制冰机等水相关家用电器和电子产品。测试环境：在一个玻璃容器外壁（玻璃1-5毫米不等），通过双面电子导热硅胶，把水位检测PCB直接贴在玻璃上面检测水位。1-8点高灵敏度电容式水位检测专用触控IC-VK36W系列水位检测背景技术：目前的检水方式主要有探针检水、水位传感器检水(光电式水位传感器,超声波水位传感器)和干簧管检水等方式，但这些方式的应用成本高，并且其安装时需要用到很长的连接线路，为了配合长的连接线路，容易使得产品的结构受到限制，并且拆装复杂，价格昴贵，不利于产品的推广及普及广泛应用。技术实现要素：为解决上述问题，本实用新型的目的在于提供一种触摸感应检水电路，能够准确检测是否有水，并且能够降低电路的成本几个等级，简化检水的结构，使得拆装便利，有利于产品的生产。 VK36WXX系列（最多支持9个检测点）是一款用于一段液位检测的专用集成电路。基于电容感应的检测原理，集成我们公司花费多年研究的独特算法，能够做到智能识别，无论是有液体上电，还是无液体上电，都能正确指示液位状态。本产品既可适用于直接接触液体的检测装置，也可适用于不直接接触液体的检测装置。尤其是非接触式的检测更安全更方便、更有优势，也可防腐蚀、防污染 1.液体检测器 2.触摸开关 3.加温器 4.喷雾器 5 水池、水箱、水缸、液体皿联系人：许先生联系手机：188 9858 2398 （微信）联系QQ：191 888 5898 E-mail：zes1688@163.com

标签： 16 36W SOP QFN 检测 VK 36 6D W6 水位

上传时间： 2019-10-21

上传用户：szqxw1688
超小封装体积四通道4检测点液体水位探测专用芯片— VK36W4D QFN16

深圳永嘉微电超高性价比水位检测芯片推出水位检测芯片可用于需要检测水位，缺水，溢出等场合。适合应用于饮水机、净饮机、咖啡机、水壶、洗碗机、制冰机等水相关家用电器和电子产品。测试环境：在一个玻璃容器外壁（玻璃1-5毫米不等），通过双面电子导热硅胶，把水位检测PCB直接贴在玻璃上面检测水位。1-8点高灵敏度电容式水位检测专用触控IC-VK36W系列水位检测背景技术：目前的检水方式主要有探针检水、水位传感器检水(光电式水位传感器,超声波水位传感器)和干簧管检水等方式，但这些方式的应用成本高，并且其安装时需要用到很长的连接线路，为了配合长的连接线路，容易使得产品的结构受到限制，并且拆装复杂，价格昴贵，不利于产品的推广及普及广泛应用。技术实现要素：为解决上述问题，本实用新型的目的在于提供一种触摸感应检水电路，能够准确检测是否有水，并且能够降低电路的成本几个等级，简化检水的结构，使得拆装便利，有利于产品的生产。 VK36WXX系列（最多支持9个检测点）是一款用于一段液位检测的专用集成电路。基于电容感应的检测原理，集成我们公司花费多年研究的独特算法，能够做到智能识别，无论是有液体上电，还是无液体上电，都能正确指示液位状态。本产品既可适用于直接接触液体的检测装置，也可适用于不直接接触液体的检测装置。尤其是非接触式的检测更安全更方便、更有优势，也可防腐蚀、防污染 1.液体检测器 2.触摸开关 3.加温器 4.喷雾器 5 水池、水箱、水缸、液体皿联系人：许先生联系手机：188 9858 2398 （微信）联系QQ：191 888 5898 E-mail：zes1688@163.com

标签： 36W QFN VK 36 16 4D W4 封装体积专用芯片

上传时间： 2019-11-06

上传用户：szsjzr1688