DC-link Automotive: MKP1849 (Customized)电动汽车电驱直流母线电容(顾客订制品)MKP1849系列.MKP1849-可集成母线排,大大降低了寄生电感,提高了系统稳定性。
上传时间: 2013-10-13
上传用户:nanfeicui
本文介绍了一种通过TTL 系列逻辑门级时序逻辑芯片设计模拟汽车尾灯工作情况电路的方法。主要阐述了通过555 系列来制作脉冲产生器,任意进制的计数器和译码器的改用等一系列方法,以及显示驱动和模式控制的电路设计。设计通过发光二极管模拟汽车尾灯来实现了汽车在行驶时候的四种情况:正常行驶,左拐弯,右拐弯,紧急刹车。
上传时间: 2013-10-15
上传用户:zhouchang199
引言 LTC4151是一款高压侧电源监视器,包含用来测量电流与电压及辅助输入电压的12位ADC。它通过广泛使用的I2C接口读取数据,并具备非同寻常的7V至80V工作电压范围,这允许其覆盖从12V汽车到48V电讯的广泛应用。
上传时间: 2013-11-14
上传用户:风行天下
倒车系统
上传时间: 2013-10-29
上传用户:ainimao
无线遥控玩具汽车源程序
上传时间: 2013-10-22
上传用户:66666
汽车转向灯程序及pr0tues
上传时间: 2013-10-27
上传用户:432234
以Freescale的S12系列16位微处理器MC9S12HY32为核心,为某电动汽车设计了一款仪表盘,实现了车速检测、步进电机控制、LCD显示、故障报警等功能。利用芯片内部资源特性设计了其硬件结构及电路,根据仪表盘的原理和工作方式设计了软件流程,并介绍了基于脉冲整形的车速信号检测的硬件设计及基于滑动时间窗口脉冲统计法的软件设计。装车试验运行稳定,有很高的实用价值。
上传时间: 2013-11-01
上传用户:海陆空653
单片机控制汽车语音技术
上传时间: 2014-11-03
上传用户:ouyang426
以C8051F020为核心处理器,设计无线传感器网络数据采集系统。系统采用SZ05-ADV型无线通讯模块组建Zigbee无线网络,结合嵌入式系统的软硬件技术,完成终端节点的8路传感器信号的数据采集。现场8路信号通过前端处理后,分别送入C8051F020的12位A/D转换器进行转换。经过精确处理、存储后的现场数据,通过Zigbee无线网络传送到上位机,系统可达到汽车试验中无线测试的目的。 Abstract: This paper designs a wireless sensor network system for data acquisition with C8051F020 as core processors.The system used SZ05-ADV wireless communication module,set up a Zigbee wireless network, combined with hardware and software technologies of embedded systems,completed the end-node 8-locale sensor signal data acquisition.Eight locale signals were sent separately into the 12-bit ADC of C8051F020 for conversion through front treatment.After accurate processing and storage,the locale data was transmitted to the host computer through Zigbee wireless.The system achieves the purpose of wireless testing in vehicle trial.
标签: C8051F020 Zigbee 汽车测试 系统设计
上传时间: 2013-11-23
上传用户:dsgkjgkjg
首先研究CAN总线和SAE J1939协议,提出一种基于MC9S12HZ256微控制器的总线式汽车数字仪表解决方案。详细介绍SAE J1939协议的报文帧格式及应用层协议中发动机相关参数的定义,以及步进电机及其驱动和车速信号的处理方法。该数字仪表系统硬件平台由微处理器和信号采集和信息处理及显示等模块组成。软件设计部分编程实现了对CAN总线和各传感器数据的读取、处理。该系统能够实时反映车辆工况。 Abstract: In this paper,CAN bus and SAE J1939protocol are researched,and a vehicle digital instrument solution based on MC9S12HZ256MCU is proposed.The message frame format and some engine-related parameters’definition in SAE J1939application layer protocol are introduced in detail.Stepper motor and its driver,the methods of speed signal process-ing are also introduced.The hardware platform of vehicle digital instrument is composed by MCU,signal acquisition mod-ule,and signal processing and displaying module.Data receiving and processing from CAN bus and sensors are accom-plished by programming,and vehicle condition can be reflected in real-time.
上传时间: 2013-10-20
上传用户:huannan88