在航天等空间产品中使用的分布式供电系统中，总体电路一般只提供27~30 V的直流一次电源，各单机产品大多采用DC/DC模块将该一次电源转换为所需的二次电源，并实现一次地与二次地的隔离。分析了INTERPOINT公司的DC/DC模块的输入端反接后，输入电压对DC/DC模块、电源保护滤波电路及负载的影响，通过仿真与验证试验，得出电源模块输入端反接后单机产品中电源保护电路发生作用，对产品中负载无影响，可以继续使用。电源模块失效分析对航天产品中电源模块中出现类似的故障后的处理提供了参考。
上传时间： 2013-11-05
上传用户：kangqiaoyibie
高的工作电压高达100V N双N沟道MOSFET同步驱动 The D810DCDC is a synchronous step-down switching regulator controller that can directly step-down voltages from up to 100V, making it ideal for telecom and automotive applications. The D810DCDC uses a constant on-time valley current control architecture to deliver very low duty cycles with accurate cycle-by-cycle current limit, without requiring a sense resistor. A precise internal reference provides 0.5% DC accuracy. A high bandwidth (25MHz) error amplifi er provides very fast line and load transient response. Large 1Ω gate drivers allow the D810DCDC to drive multiple MOSFETs for higher current applications. The operating frequency is selected by an external resistor and is compensated for variations in VIN and can also be synchronized to an external clock for switching-noise sensitive applications. Integrated bias control generates gate drive power from the input supply during start-up and when an output shortcircuit occurs, with the addition of a small external SOT23 MOSFET. When in regulation, power is derived from the output for higher effi ciency.
上传时间： 2013-10-24
上传用户：wd450412225
In a recent discussion with a system designer, the requirementfor his power supply was to regulate 1.5Vand deliver up to 40A of current to a load that consistedof four FPGAs. This is up to 60W of power that must bedelivered in a small area with the lowest height profi lepossible to allow a steady fl ow of air for cooling. Thepower supply had to be surface mountable and operateat high enough effi ciency to minimize heat dissipation.He also demanded the simplest possible solution so histime could be dedicated to the more complex tasks. Asidefrom precise electrical performance, this solution had toremovethe heat generated during DC to DC conversionquickly so that the circuit and the ICs in the vicinity do notoverheat. Such a solution requires an innovative designto meet these criteria:
上传时间： 2013-11-24
上传用户：defghi010
Photomultipliers (PMT), avalanche photodiodes (APD),ultrasonic transducers, capacitance microphones, radiationdetectors and similar devices require high voltage,low current bias. Additionally, the high voltage must bepristinely free of noise; well under a millivolt is a commonrequirement with a few hundred microvolts sometimesnecessary. Normally, switching regulator confi gurationscannot achieve this performance level without employingspecial techniques. One aid to achieving low noise is thatload currents rarely exceed 5mA. This freedom permitsoutput fi ltering methods that are usually impractical
上传时间： 2013-10-28
上传用户：lhw888
The LTM4600 DC/DC μModule regulator is a complete highpower density stepdown regulator for 10A continuous (14Apeak) loads. The device has two voltage options: 20VINmaximum for the LTM4600EV and 28VIN maximum for theLTM4600HVEV each housed in a small 15mm ¥ 15mm ¥2.8mm LGA surface mount package.
上传时间： 2013-10-10
上传用户：adada
The LTM8020, LTM8021, LTM8022 and LTM8023 μModule®regulators are complete easy-to-use encapsulated stepdownDC/DC regulators intended to take the pain and aggravationout of implementing a switching power supplyonto a system board. With a μModule regulator, you onlyneed an input cap, output cap and one or two resistorsto complete the design. As one might imagine, this highlevel of integration greatly simplifi es the task of printedcircuit board design, reducing the effort to four categories:component footprint generation, component placement,routing the nets, and thermal vias.
上传时间： 2014-01-18
上传用户：laomv123
The design of battery-powered equipment can often bequite challenging. Since few ICs can operate directly fromthe end-of-life voltage from a 2-cell battery (about 1.8V),most systems require a DC/DCconverter. The systemdesigner often has a limited area in which to place the DC/DC converter; associated inductors and capacitors must be
上传时间： 2013-11-23
上传用户：wys0120
触摸开关电路也叫触摸式调光、开关控制电路，主要用于生活中白炽灯光的控制。它与一个主要由双向可控硅组成的外围电路一起对光源进行调光、开关的触摸式控制，并具有记忆功能。摆脱了传统的机械拨动开关、电位器调光的形式，是一种新颖的升级换代产品。电路由输入缓冲器、锁相环、控制逻辑、亮度记忆、相角指针、数字比较器和输出驱动器组成。其框图见图１
上传时间： 2013-11-11
上传用户：tiantwo
利用推挽正激变换技术设计了DC /DC开关电源。提出了基于推挽正激变换技术的电源电路拓扑和结构,阐述了该开关电源的工作及控制原理,并利用PSp ice软件对该电路拓扑进行了仿真。实验结果表明,该开关电源输出稳定、波形理想。
上传时间： 2013-10-21
上传用户：363186
一种好的蓄电池充电方法是分级恒流充电! 分析了PWM控制DCDC变换的原理"给出了一种基于IGBT功率器件#单片机控制的新型蓄电池恒流充电系统的设计方法"并对该系统进行了试验"给出了试验结果!
上传时间： 2013-10-21
上传用户：mqien
