第二部分：DRAM 内存模块的设计技术..............................................................143第一章 SDR 和DDR 内存的比较..........................................................................143第二章 内存模块的叠层设计.............................................................................145第三章 内存模块的时序要求.............................................................................1493.1 无缓冲（Unbuffered）内存模块的时序分析.......................................1493.2 带寄存器（Registered）的内存模块时序分析...................................154第四章 内存模块信号设计.................................................................................1594.1 时钟信号的设计.......................................................................................1594.2 CS 及CKE 信号的设计..............................................................................1624.3 地址和控制线的设计...............................................................................1634.4 数据信号线的设计...................................................................................1664.5 电源，参考电压Vref 及去耦电容.........................................................169第五章 内存模块的功耗计算.............................................................................172第六章 实际设计案例分析.................................................................................178 目前比较流行的内存模块主要是这三种：SDR，DDR，RAMBUS。其中，RAMBUS内存采用阻抗受控制的串行连接技术,在这里我们将不做进一步探讨，本文所总结的内存设计技术就是针对SDRAM 而言(包括SDR 和DDR)。现在我们来简单地比较一下SDR 和DDR，它们都被称为同步动态内存，其核心技术是一样的。只是DDR 在某些功能上进行了改进，所以DDR 有时也被称为SDRAM II。DDR 的全称是Double Data Rate，也就是双倍的数据传输率，但是其时钟频率没有增加，只是在时钟的上升和下降沿都可以用来进行数据的读写操作。对于SDR 来说,市面上常见的模块主要有PC100/PC133/PC166,而相应的DDR内存则为DDR200(PC1600)/DDR266(PC2100)/DDR333(PC2700)。
上传时间： 2014-01-13
上传用户：euroford
现代的电子设计和芯片制造技术正在飞速发展，电子产品的复杂度、时钟和总线频率等等都呈快速上升趋势，但系统的电压却不断在减小，所有的这一切加上产品投放市场的时间要求给设计师带来了前所未有的巨大压力。要想保证产品的一次性成功就必须能预见设计中可能出现的各种问题，并及时给出合理的解决方案，对于高速的数字电路来说，最令人头大的莫过于如何确保瞬时跳变的数字信号通过较长的一段传输线，还能完整地被接收，并保证良好的电磁兼容性，这就是目前颇受关注的信号完整性（SI）问题。本章就是围绕信号完整性的问题，让大家对高速电路有个基本的认识，并介绍一些相关的基本概念。 第一章 高速数字电路概述.....................................................................................51.1 何为高速电路...............................................................................................51.2 高速带来的问题及设计流程剖析...............................................................61.3 相关的一些基本概念...................................................................................8第二章 传输线理论...............................................................................................122.1 分布式系统和集总电路.............................................................................122.2 传输线的RLCG 模型和电报方程...............................................................132.3 传输线的特征阻抗.....................................................................................142.3.1 特性阻抗的本质.................................................................................142.3.2 特征阻抗相关计算.............................................................................152.3.3 特性阻抗对信号完整性的影响.........................................................172.4 传输线电报方程及推导.............................................................................182.5 趋肤效应和集束效应.................................................................................232.6 信号的反射.................................................................................................252.6.1 反射机理和电报方程.........................................................................252.6.2 反射导致信号的失真问题.................................................................302.6.2.1 过冲和下冲.....................................................................................302.6.2.2 振荡：.............................................................................................312.6.3 反射的抑制和匹配.............................................................................342.6.3.1 串行匹配.........................................................................................352.6.3.1 并行匹配.........................................................................................362.6.3.3 差分线的匹配.................................................................................392.6.3.4 多负载的匹配.................................................................................41第三章 串扰的分析...............................................................................................423.1 串扰的基本概念.........................................................................................423.2 前向串扰和后向串扰.................................................................................433.3 后向串扰的反射.........................................................................................463.4 后向串扰的饱和.........................................................................................463.5 共模和差模电流对串扰的影响.................................................................483.6 连接器的串扰问题.....................................................................................513.7 串扰的具体计算.........................................................................................543.8 避免串扰的措施.........................................................................................57第四章 EMI 抑制....................................................................................................604.1 EMI/EMC 的基本概念..................................................................................604.2 EMI 的产生..................................................................................................614.2.1 电压瞬变.............................................................................................614.2.2 信号的回流.........................................................................................624.2.3 共模和差摸EMI ..................................................................................634.3 EMI 的控制..................................................................................................654.3.1 屏蔽.....................................................................................................654.3.1.1 电场屏蔽.........................................................................................654.3.1.2 磁场屏蔽.........................................................................................674.3.1.3 电磁场屏蔽.....................................................................................674.3.1.4 电磁屏蔽体和屏蔽效率.................................................................684.3.2 滤波.....................................................................................................714.3.2.1 去耦电容.........................................................................................714.3.2.3 磁性元件.........................................................................................734.3.3 接地.....................................................................................................744.4 PCB 设计中的EMI.......................................................................................754.4.1 传输线RLC 参数和EMI ........................................................................764.4.2 叠层设计抑制EMI ..............................................................................774.4.3 电容和接地过孔对回流的作用.........................................................784.4.4 布局和走线规则.................................................................................79第五章 电源完整性理论基础...............................................................................825.1 电源噪声的起因及危害.............................................................................825.2 电源阻抗设计.............................................................................................855.3 同步开关噪声分析.....................................................................................875.3.1 芯片内部开关噪声.............................................................................885.3.2 芯片外部开关噪声.............................................................................895.3.3 等效电感衡量SSN ..............................................................................905.4 旁路电容的特性和应用.............................................................................925.4.1 电容的频率特性.................................................................................935.4.3 电容的介质和封装影响.....................................................................955.4.3 电容并联特性及反谐振.....................................................................955.4.4 如何选择电容.....................................................................................975.4.5 电容的摆放及Layout ........................................................................99第六章 系统时序.................................................................................................1006.1 普通时序系统...........................................................................................1006.1.1 时序参数的确定...............................................................................1016.1.2 时序约束条件...................................................................................1066.2 源同步时序系统.......................................................................................1086.2.1 源同步系统的基本结构...................................................................1096.2.2 源同步时序要求...............................................................................110第七章 IBIS 模型................................................................................................1137.1 IBIS 模型的由来...................................................................................... 1137.2 IBIS 与SPICE 的比较.............................................................................. 1137.3 IBIS 模型的构成...................................................................................... 1157.4 建立IBIS 模型......................................................................................... 1187.4 使用IBIS 模型......................................................................................... 1197.5 IBIS 相关工具及链接..............................................................................120第八章 高速设计理论在实际中的运用.............................................................1228.1 叠层设计方案...........................................................................................1228.2 过孔对信号传输的影响...........................................................................1278.3 一般布局规则...........................................................................................1298.4 接地技术...................................................................................................1308.5 PCB 走线策略............................................................................................134
标签： 信号完整性
上传时间： 2014-05-15
上传用户：dudu1210004
当你认为你已经掌握了PCB 走线的特征阻抗Z0，紧接着一份数据手册告诉你去设计一个特定的差分阻抗。令事情变得更困难的是，它说：“……因为两根走线之间的耦合可以降低有效阻抗，使用50Ω的设计规则来得到一个大约80Ω的差分阻抗！”这的确让人感到困惑！这篇文章向你展示什么是差分阻抗。除此之外，还讨论了为什么是这样，并且向你展示如何正确地计算它。 单线：图1(a)演示了一个典型的单根走线。其特征阻抗是Z0，其上流经的电流为i。沿线任意一点的电压为V=Z0*i（ 根据欧姆定律）。一般情况，线对：图1(b)演示了一对走线。线1 具有特征阻抗Z11，与上文中Z0 一致，电流i1。线2具有类似的定义。当我们将线2 向线1 靠近时，线2 上的电流开始以比例常数k 耦合到线1 上。类似地，线1 的电流i1 开始以同样的比例常数耦合到线2 上。每根走线上任意一点的电压，还是根据欧姆定律，
标签： 差分阻抗
上传时间： 2013-10-20
上传用户：lwwhust
第一部分 信号完整性知识基础.................................................................................5第一章 高速数字电路概述.....................................................................................51.1 何为高速电路...............................................................................................51.2 高速带来的问题及设计流程剖析...............................................................61.3 相关的一些基本概念...................................................................................8第二章 传输线理论...............................................................................................122.1 分布式系统和集总电路.............................................................................122.2 传输线的RLCG 模型和电报方程...............................................................132.3 传输线的特征阻抗.....................................................................................142.3.1 特性阻抗的本质.................................................................................142.3.2 特征阻抗相关计算.............................................................................152.3.3 特性阻抗对信号完整性的影响.........................................................172.4 传输线电报方程及推导.............................................................................182.5 趋肤效应和集束效应.................................................................................232.6 信号的反射.................................................................................................252.6.1 反射机理和电报方程.........................................................................252.6.2 反射导致信号的失真问题.................................................................302.6.2.1 过冲和下冲.....................................................................................302.6.2.2 振荡：.............................................................................................312.6.3 反射的抑制和匹配.............................................................................342.6.3.1 串行匹配.........................................................................................352.6.3.1 并行匹配.........................................................................................362.6.3.3 差分线的匹配.................................................................................392.6.3.4 多负载的匹配.................................................................................41第三章 串扰的分析...............................................................................................423.1 串扰的基本概念.........................................................................................423.2 前向串扰和后向串扰.................................................................................433.3 后向串扰的反射.........................................................................................463.4 后向串扰的饱和.........................................................................................463.5 共模和差模电流对串扰的影响.................................................................483.6 连接器的串扰问题.....................................................................................513.7 串扰的具体计算.........................................................................................543.8 避免串扰的措施.........................................................................................57第四章 EMI 抑制....................................................................................................604.1 EMI/EMC 的基本概念..................................................................................604.2 EMI 的产生..................................................................................................614.2.1 电压瞬变.............................................................................................614.2.2 信号的回流.........................................................................................624.2.3 共模和差摸EMI ..................................................................................634.3 EMI 的控制..................................................................................................654.3.1 屏蔽.....................................................................................................654.3.1.1 电场屏蔽.........................................................................................654.3.1.2 磁场屏蔽.........................................................................................674.3.1.3 电磁场屏蔽.....................................................................................674.3.1.4 电磁屏蔽体和屏蔽效率.................................................................684.3.2 滤波.....................................................................................................714.3.2.1 去耦电容.........................................................................................714.3.2.3 磁性元件.........................................................................................734.3.3 接地.....................................................................................................744.4 PCB 设计中的EMI.......................................................................................754.4.1 传输线RLC 参数和EMI ........................................................................764.4.2 叠层设计抑制EMI ..............................................................................774.4.3 电容和接地过孔对回流的作用.........................................................784.4.4 布局和走线规则.................................................................................79第五章 电源完整性理论基础...............................................................................825.1 电源噪声的起因及危害.............................................................................825.2 电源阻抗设计.............................................................................................855.3 同步开关噪声分析.....................................................................................875.3.1 芯片内部开关噪声.............................................................................885.3.2 芯片外部开关噪声.............................................................................895.3.3 等效电感衡量SSN ..............................................................................905.4 旁路电容的特性和应用.............................................................................925.4.1 电容的频率特性.................................................................................935.4.3 电容的介质和封装影响.....................................................................955.4.3 电容并联特性及反谐振.....................................................................955.4.4 如何选择电容.....................................................................................975.4.5 电容的摆放及Layout ........................................................................99第六章 系统时序.................................................................................................1006.1 普通时序系统...........................................................................................1006.1.1 时序参数的确定...............................................................................1016.1.2 时序约束条件...................................................................................1063.2 高速设计的问题.......................................................................................2093.3 SPECCTRAQuest SI Expert 的组件.......................................................2103.3.1 SPECCTRAQuest Model Integrity .................................................2103.3.2 SPECCTRAQuest Floorplanner/Editor .........................................2153.3.3 Constraint Manager .......................................................................2163.3.4 SigXplorer Expert Topology Development Environment .......2233.3.5 SigNoise 仿真子系统......................................................................2253.3.6 EMControl .........................................................................................2303.3.7 SPECCTRA Expert 自动布线器.......................................................2303.4 高速设计的大致流程...............................................................................2303.4.1 拓扑结构的探索...............................................................................2313.4.2 空间解决方案的探索.......................................................................2313.4.3 使用拓扑模板驱动设计...................................................................2313.4.4 时序驱动布局...................................................................................2323.4.5 以约束条件驱动设计.......................................................................2323.4.6 设计后分析.......................................................................................233第四章 SPECCTRAQUEST SIGNAL EXPLORER 的进阶运用..........................................2344.1 SPECCTRAQuest Signal Explorer 的功能包括：................................2344.2 图形化的拓扑结构探索...........................................................................2344.3 全面的信号完整性(Signal Integrity)分析.......................................2344.4 完全兼容 IBIS 模型...............................................................................2344.5 PCB 设计前和设计的拓扑结构提取.......................................................2354.6 仿真设置顾问...........................................................................................2354.7 改变设计的管理.......................................................................................2354.8 关键技术特点...........................................................................................2364.8.1 拓扑结构探索...................................................................................2364.8.2 SigWave 波形显示器........................................................................2364.8.3 集成化的在线分析(Integration and In-process Analysis) .236第五章 部分特殊的运用...............................................................................2375.1 Script 指令的使用..................................................................................2375.2 差分信号的仿真.......................................................................................2435.3 眼图模式的使用.......................................................................................249第四部分：HYPERLYNX 仿真工具使用指南............................................................251第一章 使用LINESIM 进行前仿真.......................................................................2511.1 用LineSim 进行仿真工作的基本方法...................................................2511.2 处理信号完整性原理图的具体问题.......................................................2591.3 在LineSim 中如何对传输线进行设置...................................................2601.4 在LineSim 中模拟IC 元件.....................................................................2631.5 在LineSim 中进行串扰仿真...................................................................268第二章 使用BOARDSIM 进行后仿真......................................................................2732.1 用BOARDSIM 进行后仿真工作的基本方法...................................................2732.2 BoardSim 的进一步介绍..........................................................................2922.3 BoardSim 中的串扰仿真..........................................................................309
上传时间： 2014-04-18
上传用户：wpt
1 为什么要重视电源噪声问题？ 2 电源系统噪声余量分析 3 电源噪声是如何产生的？ 4 电容退耦的两种解释 4.1 从储能的角度来说明电容退耦原理。 4.2 从阻抗的角度来理解退耦原理。 5 实际电容的特性 6 电容的安装谐振频率 7 局部去耦设计方法 8 电源系统的角度进行去耦设计 8.1 著名的Target Impedance（目标阻抗） 8.2 需要多大的电容量 8.3 相同容值电容的并联 8.4 不同容值电容的并联与反谐振（Anti-Resonance） 8.5 ESR 对反谐振（Anti-Resonance）的影响 8.6 怎样合理选择电容组合 8.7 电容的去耦半径 8.8 电容的安装方法 9 结束语
标签： 电源完整性
上传时间： 2013-11-06
上传用户：mahone
LonWorks 推广应用的关键在于网络节点开发， 以TP ／ FT-10F 模块和AT89C2051 单片机为核心设计接口电路，开发了一种通用多输入／ 输出智能控制节点模块。通过软件调整模拟信号采集电路的量程；应用DAC7513 使放大器输出电压几乎等于电源电压；采用二极管隔离方式简化数字信号输入／ 输出电路；通过在电源引脚和接地引脚之间添加去耦电容，采用多层电路板布局，数字芯片的未用输入端接入高电平等方法，提高了抗电磁干扰能力；采取模拟、数字电路单元内部分别接模拟地和数字地，再将2 条地线接至一点的措施，有效地降低了静态放电的影响；提出了节点故障诊断策略流程。该通用多输入／ 输出智能控制节点模块运行可靠。关键词： LonWorks； 多输入／ 输出； 节点设计
上传时间： 2013-11-23
上传用户：515414293
PCB布线设计－模拟和数字布线的异同工程领域中的数字设计人员和数字电路板设计专家在不断增加，这反映了行业的发展趋势。尽管对数字设计的重视带来了电子产品的重大发展，但仍然存在，而且还会一直存在一部分与 模拟 或现实环境接口的电路设计。模拟和数字领域的布线策略有一些类似之处，但要获得更好的工程领域中的数字设计人员和数字电路板设计专家在不断增加，这反映了行业的发展趋势。尽管对数字设计的重视带来了电子产品的重大发展，但仍然存在，而且还会一直存在一部分与模拟或现实环境接口的电路设计。模拟和数字领域的布线策略有一些类似之处，但要获得更好的结果时，由于其布线策略不同，简单电路布线设计就不再是最优方案了。本文就旁路电容、电源、地线设计、电压误差和由PCB布线引起的电磁干扰(EMI)等几个方面，讨论模拟和数字布线的基本相似之处及差别。模拟和数字布线策略的相似之处旁路或去耦电容在布线时，模拟器件和数字器件都需要这些类型的电容，都需要靠近其电源引脚连接一个电容，此电容值通常为0.1mF。系统供电电源侧需要另一类电容，通常此电容值大约为10mF。这些电容的位置如图1所示。电容取值范围为推荐值的1/10至10倍之间。但引脚须较短，且要尽量靠近器件(对于0.1mF电容)或供电电源(对于10mF电容)。在电路板上加旁路或去耦电容，以及这些电容在板上的位置，对于数字和模拟设计来说都属于常识。但有趣的是，其原因却有所不同。在模拟布线设计中，旁路电容通常用于旁路电源上的高频信号，如果不加旁路电容，这些高频信号可能通过电源引脚进入敏感的模拟芯片。一般来说，这些高频信号的频率超出模拟器件抑制高频信号的能力。如果在模拟电路中不使用旁路电容的话，就可能在信号路径上引入噪声，更严重的情况甚至会引起振动。
上传时间： 2013-11-05
上传用户：604759954
第二部分：DRAM 内存模块的设计技术..............................................................143第一章 SDR 和DDR 内存的比较..........................................................................143第二章 内存模块的叠层设计.............................................................................145第三章 内存模块的时序要求.............................................................................1493.1 无缓冲（Unbuffered）内存模块的时序分析.......................................1493.2 带寄存器（Registered）的内存模块时序分析...................................154第四章 内存模块信号设计.................................................................................1594.1 时钟信号的设计.......................................................................................1594.2 CS 及CKE 信号的设计..............................................................................1624.3 地址和控制线的设计...............................................................................1634.4 数据信号线的设计...................................................................................1664.5 电源，参考电压Vref 及去耦电容.........................................................169第五章 内存模块的功耗计算.............................................................................172第六章 实际设计案例分析.................................................................................178 目前比较流行的内存模块主要是这三种：SDR，DDR，RAMBUS。其中，RAMBUS内存采用阻抗受控制的串行连接技术,在这里我们将不做进一步探讨，本文所总结的内存设计技术就是针对SDRAM 而言(包括SDR 和DDR)。现在我们来简单地比较一下SDR 和DDR，它们都被称为同步动态内存，其核心技术是一样的。只是DDR 在某些功能上进行了改进，所以DDR 有时也被称为SDRAM II。DDR 的全称是Double Data Rate，也就是双倍的数据传输率，但是其时钟频率没有增加，只是在时钟的上升和下降沿都可以用来进行数据的读写操作。对于SDR 来说,市面上常见的模块主要有PC100/PC133/PC166,而相应的DDR内存则为DDR200(PC1600)/DDR266(PC2100)/DDR333(PC2700)。
上传时间： 2013-10-18
上传用户：宋桃子
现代的电子设计和芯片制造技术正在飞速发展，电子产品的复杂度、时钟和总线频率等等都呈快速上升趋势，但系统的电压却不断在减小，所有的这一切加上产品投放市场的时间要求给设计师带来了前所未有的巨大压力。要想保证产品的一次性成功就必须能预见设计中可能出现的各种问题，并及时给出合理的解决方案，对于高速的数字电路来说，最令人头大的莫过于如何确保瞬时跳变的数字信号通过较长的一段传输线，还能完整地被接收，并保证良好的电磁兼容性，这就是目前颇受关注的信号完整性（SI）问题。本章就是围绕信号完整性的问题，让大家对高速电路有个基本的认识，并介绍一些相关的基本概念。 第一章 高速数字电路概述.....................................................................................51.1 何为高速电路...............................................................................................51.2 高速带来的问题及设计流程剖析...............................................................61.3 相关的一些基本概念...................................................................................8第二章 传输线理论...............................................................................................122.1 分布式系统和集总电路.............................................................................122.2 传输线的RLCG 模型和电报方程...............................................................132.3 传输线的特征阻抗.....................................................................................142.3.1 特性阻抗的本质.................................................................................142.3.2 特征阻抗相关计算.............................................................................152.3.3 特性阻抗对信号完整性的影响.........................................................172.4 传输线电报方程及推导.............................................................................182.5 趋肤效应和集束效应.................................................................................232.6 信号的反射.................................................................................................252.6.1 反射机理和电报方程.........................................................................252.6.2 反射导致信号的失真问题.................................................................302.6.2.1 过冲和下冲.....................................................................................302.6.2.2 振荡：.............................................................................................312.6.3 反射的抑制和匹配.............................................................................342.6.3.1 串行匹配.........................................................................................352.6.3.1 并行匹配.........................................................................................362.6.3.3 差分线的匹配.................................................................................392.6.3.4 多负载的匹配.................................................................................41第三章 串扰的分析...............................................................................................423.1 串扰的基本概念.........................................................................................423.2 前向串扰和后向串扰.................................................................................433.3 后向串扰的反射.........................................................................................463.4 后向串扰的饱和.........................................................................................463.5 共模和差模电流对串扰的影响.................................................................483.6 连接器的串扰问题.....................................................................................513.7 串扰的具体计算.........................................................................................543.8 避免串扰的措施.........................................................................................57第四章 EMI 抑制....................................................................................................604.1 EMI/EMC 的基本概念..................................................................................604.2 EMI 的产生..................................................................................................614.2.1 电压瞬变.............................................................................................614.2.2 信号的回流.........................................................................................624.2.3 共模和差摸EMI ..................................................................................634.3 EMI 的控制..................................................................................................654.3.1 屏蔽.....................................................................................................654.3.1.1 电场屏蔽.........................................................................................654.3.1.2 磁场屏蔽.........................................................................................674.3.1.3 电磁场屏蔽.....................................................................................674.3.1.4 电磁屏蔽体和屏蔽效率.................................................................684.3.2 滤波.....................................................................................................714.3.2.1 去耦电容.........................................................................................714.3.2.3 磁性元件.........................................................................................734.3.3 接地.....................................................................................................744.4 PCB 设计中的EMI.......................................................................................754.4.1 传输线RLC 参数和EMI ........................................................................764.4.2 叠层设计抑制EMI ..............................................................................774.4.3 电容和接地过孔对回流的作用.........................................................784.4.4 布局和走线规则.................................................................................79第五章 电源完整性理论基础...............................................................................825.1 电源噪声的起因及危害.............................................................................825.2 电源阻抗设计.............................................................................................855.3 同步开关噪声分析.....................................................................................875.3.1 芯片内部开关噪声.............................................................................885.3.2 芯片外部开关噪声.............................................................................895.3.3 等效电感衡量SSN ..............................................................................905.4 旁路电容的特性和应用.............................................................................925.4.1 电容的频率特性.................................................................................935.4.3 电容的介质和封装影响.....................................................................955.4.3 电容并联特性及反谐振.....................................................................955.4.4 如何选择电容.....................................................................................975.4.5 电容的摆放及Layout ........................................................................99第六章 系统时序.................................................................................................1006.1 普通时序系统...........................................................................................1006.1.1 时序参数的确定...............................................................................1016.1.2 时序约束条件...................................................................................1066.2 源同步时序系统.......................................................................................1086.2.1 源同步系统的基本结构...................................................................1096.2.2 源同步时序要求...............................................................................110第七章 IBIS 模型................................................................................................1137.1 IBIS 模型的由来...................................................................................... 1137.2 IBIS 与SPICE 的比较.............................................................................. 1137.3 IBIS 模型的构成...................................................................................... 1157.4 建立IBIS 模型......................................................................................... 1187.4 使用IBIS 模型......................................................................................... 1197.5 IBIS 相关工具及链接..............................................................................120第八章 高速设计理论在实际中的运用.............................................................1228.1 叠层设计方案...........................................................................................1228.2 过孔对信号传输的影响...........................................................................1278.3 一般布局规则...........................................................................................1298.4 接地技术...................................................................................................1308.5 PCB 走线策略............................................................................................134
标签： 信号完整性
上传时间： 2013-11-01
上传用户：xitai
第一部分 信号完整性知识基础.................................................................................5第一章 高速数字电路概述.....................................................................................51.1 何为高速电路...............................................................................................51.2 高速带来的问题及设计流程剖析...............................................................61.3 相关的一些基本概念...................................................................................8第二章 传输线理论...............................................................................................122.1 分布式系统和集总电路.............................................................................122.2 传输线的RLCG 模型和电报方程...............................................................132.3 传输线的特征阻抗.....................................................................................142.3.1 特性阻抗的本质.................................................................................142.3.2 特征阻抗相关计算.............................................................................152.3.3 特性阻抗对信号完整性的影响.........................................................172.4 传输线电报方程及推导.............................................................................182.5 趋肤效应和集束效应.................................................................................232.6 信号的反射.................................................................................................252.6.1 反射机理和电报方程.........................................................................252.6.2 反射导致信号的失真问题.................................................................302.6.2.1 过冲和下冲.....................................................................................302.6.2.2 振荡：.............................................................................................312.6.3 反射的抑制和匹配.............................................................................342.6.3.1 串行匹配.........................................................................................352.6.3.1 并行匹配.........................................................................................362.6.3.3 差分线的匹配.................................................................................392.6.3.4 多负载的匹配.................................................................................41第三章 串扰的分析...............................................................................................423.1 串扰的基本概念.........................................................................................423.2 前向串扰和后向串扰.................................................................................433.3 后向串扰的反射.........................................................................................463.4 后向串扰的饱和.........................................................................................463.5 共模和差模电流对串扰的影响.................................................................483.6 连接器的串扰问题.....................................................................................513.7 串扰的具体计算.........................................................................................543.8 避免串扰的措施.........................................................................................57第四章 EMI 抑制....................................................................................................604.1 EMI/EMC 的基本概念..................................................................................604.2 EMI 的产生..................................................................................................614.2.1 电压瞬变.............................................................................................614.2.2 信号的回流.........................................................................................624.2.3 共模和差摸EMI ..................................................................................634.3 EMI 的控制..................................................................................................654.3.1 屏蔽.....................................................................................................654.3.1.1 电场屏蔽.........................................................................................654.3.1.2 磁场屏蔽.........................................................................................674.3.1.3 电磁场屏蔽.....................................................................................674.3.1.4 电磁屏蔽体和屏蔽效率.................................................................684.3.2 滤波.....................................................................................................714.3.2.1 去耦电容.........................................................................................714.3.2.3 磁性元件.........................................................................................734.3.3 接地.....................................................................................................744.4 PCB 设计中的EMI.......................................................................................754.4.1 传输线RLC 参数和EMI ........................................................................764.4.2 叠层设计抑制EMI ..............................................................................774.4.3 电容和接地过孔对回流的作用.........................................................784.4.4 布局和走线规则.................................................................................79第五章 电源完整性理论基础...............................................................................825.1 电源噪声的起因及危害.............................................................................825.2 电源阻抗设计.............................................................................................855.3 同步开关噪声分析.....................................................................................875.3.1 芯片内部开关噪声.............................................................................885.3.2 芯片外部开关噪声.............................................................................895.3.3 等效电感衡量SSN ..............................................................................905.4 旁路电容的特性和应用.............................................................................925.4.1 电容的频率特性.................................................................................935.4.3 电容的介质和封装影响.....................................................................955.4.3 电容并联特性及反谐振.....................................................................955.4.4 如何选择电容.....................................................................................975.4.5 电容的摆放及Layout ........................................................................99第六章 系统时序.................................................................................................1006.1 普通时序系统...........................................................................................1006.1.1 时序参数的确定...............................................................................1016.1.2 时序约束条件...................................................................................1063.2 高速设计的问题.......................................................................................2093.3 SPECCTRAQuest SI Expert 的组件.......................................................2103.3.1 SPECCTRAQuest Model Integrity .................................................2103.3.2 SPECCTRAQuest Floorplanner/Editor .........................................2153.3.3 Constraint Manager .......................................................................2163.3.4 SigXplorer Expert Topology Development Environment .......2233.3.5 SigNoise 仿真子系统......................................................................2253.3.6 EMControl .........................................................................................2303.3.7 SPECCTRA Expert 自动布线器.......................................................2303.4 高速设计的大致流程...............................................................................2303.4.1 拓扑结构的探索...............................................................................2313.4.2 空间解决方案的探索.......................................................................2313.4.3 使用拓扑模板驱动设计...................................................................2313.4.4 时序驱动布局...................................................................................2323.4.5 以约束条件驱动设计.......................................................................2323.4.6 设计后分析.......................................................................................233第四章 SPECCTRAQUEST SIGNAL EXPLORER 的进阶运用..........................................2344.1 SPECCTRAQuest Signal Explorer 的功能包括：................................2344.2 图形化的拓扑结构探索...........................................................................2344.3 全面的信号完整性(Signal Integrity)分析.......................................2344.4 完全兼容 IBIS 模型...............................................................................2344.5 PCB 设计前和设计的拓扑结构提取.......................................................2354.6 仿真设置顾问...........................................................................................2354.7 改变设计的管理.......................................................................................2354.8 关键技术特点...........................................................................................2364.8.1 拓扑结构探索...................................................................................2364.8.2 SigWave 波形显示器........................................................................2364.8.3 集成化的在线分析(Integration and In-process Analysis) .236第五章 部分特殊的运用...............................................................................2375.1 Script 指令的使用..................................................................................2375.2 差分信号的仿真.......................................................................................2435.3 眼图模式的使用.......................................................................................249第四部分：HYPERLYNX 仿真工具使用指南............................................................251第一章 使用LINESIM 进行前仿真.......................................................................2511.1 用LineSim 进行仿真工作的基本方法...................................................2511.2 处理信号完整性原理图的具体问题.......................................................2591.3 在LineSim 中如何对传输线进行设置...................................................2601.4 在LineSim 中模拟IC 元件.....................................................................2631.5 在LineSim 中进行串扰仿真...................................................................268第二章 使用BOARDSIM 进行后仿真......................................................................2732.1 用BOARDSIM 进行后仿真工作的基本方法...................................................2732.2 BoardSim 的进一步介绍..........................................................................2922.3 BoardSim 中的串扰仿真..........................................................................309
上传时间： 2013-11-07
上传用户：aa7821634
