本人的毕业设计论文，利用单片机AT89S52和温湿度传感器DHT11，实现温湿度检测、报警以及发送至PC，而且还有供电电源的设计。 内容很全面，有完整的keil C51程序以及电路图等，欢迎参考，指出不足。
上传时间： 2013-10-16
上传用户：ssz1990
摘 要: 阀门开度仪以AT89C51单片机为核心, 通过在阀门电机轴上安装的电位计传感器获得阀 门电机轴的转动角位移, 从而得出阀门的开度, 达到自动检测的目的。详细介绍了串行控制的10 位A /D转换器TLC1549的特点和功能, 说明了TLC1549与AT89C51单片机在阀门开度仪中的硬件 电路和软件程序。实践证明, 该阀门开度仪数据采集准确可靠、工作稳定。 关键词: TLC1549; AT89C51单片机; 阀门开度
上传时间： 2013-10-14
上传用户：行者Xin
在深入了解Flash存储器的基础上，采用单片机自动检测存储器无效块。主要通过读取每一块的第1、第2页内容，判断该块的好坏，并给出具体的实现过程，以及部分关键的电路原理图和C语言程序代码。该设计最终实现单片机自动检测Flash坏块的功能，并通过读取ID号检测Flash的性能，同时该设计能够存储和读取1GB数据。 Abstract: On the basis of in-depth understanding the Flash chips，this paper designs a new program which using the SCM to detect the invalid block.Mainly through reading the data of the first and second page to detect the invalid block.Specific implementation procedure was given,and the key circuit schematic diagram and C language program code was introduced.This design achieved the function of using the MCU checks the invalid block finally，and increased the function by reading the ID number of Flash to get the performance of the memory.And the design also can write and read1GB data
上传时间： 2013-10-25
上传用户：taozhihua1314
阐述了一个由上位PC机和AT89C52下位单片机组成的主从分布式温度巡回检测系统。主从机采用RS-485 串行通讯标准进行通信，可在下位单片机实现基本的温度数据巡回检测基础上，由上位PC机实现综合处理功能或扩展为远程操作。整个系统具有巡检速度快，扩展性好的特点。 Abstract: In this paper,a top PC and AT89C52 under-bit microcontrollers from the main component of the tour distributed temperature detection system is presented. Master and slave can use RS-485 serial communication standards for communications.Based on next-bit machine for basic goods temperature detected data Tour, the top can achieve the integrated treatment of PC functions or for the expansion of long-distance operation. The entire inspection system is fast, expansion.
上传时间： 2013-10-13
上传用户：zhoujunzhen
在汽车发动机起动时，若发动机起动后起动机不能及时断电，将会烧毁起动机或损坏飞轮齿环；若变速器不在空档位置起动，则起动机的瞬间动力将使汽车位移，还可能引起交通事故和人身安全。为此介绍一种利用NXP P89LPC901单片机控制的汽车起动保护控制器，通过检测汽车起动开关、变速箱档位、发动机转速，实现对汽车发动机起动过程检测和保护。起动保护控制器在发动机起动过程中通过采用逐个关闭打开负载系统，解决汽车发动机过程中因起动电流大而对汽车电源的冲击影响,延长了电瓶寿命。 Abstract: When the automotive engine is started, the engine start motor and flywheel gear may be damaged， even traffic accidents and personal safeties may be caused by wrong operation or other factors.In order to ensure the automotive engine can be started normally and safely,it is necessary that the protecting measures and methods are considered in the automotive electrical control system.This paper introduces a kind of the automotive engine starting protect controller based on NXP P89LPC901 MCU.The controller can protect the engine starting process by detecting the starter key switch,transmission stall and engine speed.Through the use of close and open load system,the controller can solve the impact on automotive power because of the high-current load in the process of the automobile engine starting, and extend battery life.
上传时间： 2013-10-15
上传用户：mikesering
针对材料试验机等设备中要求测量或控制材料拉伸或压缩的位移，一般采用光电轴角编码器检测位置信号，输出正交编码脉冲信号。若采用其他方法检测位置信号，必然导致电路设计复杂，可靠性降低。因此，提出一种基于LS7266R1的电子式万能材料试验机设计方案。给出了试验机中的控制器工作原理，LS7266R1与单片机的接口硬件设计，以及主程序软件流程图。巧妙地把力量传感器，位移传感器等机械运动状态的压力或拉力以及位置坐标，变成了电压信号和电脉冲数字信号，供A/D测量和LS7266R1计数，从而实现了独立完成材料试验控制或通过PC机串口命令完成材料试验控制。 Abstract: Aiming at the requirement that the displacement of the tension and compression always be tested and controlled in the equipement such as material testing machine. The position signal was tested by photoelectric axial angle coder. Therefore， the paper proposes the design of electronic universal testing machine design based on LS7266R1. If the position signal detected by other methods， will inevitably lead to the circuit design complexity， reliability decreased. The work theory of the controller， the hardware interface design between LS7266R1 and single chip， and the flow chart of main program， are presented in this paper. The signal of the compression or tension power and displacement at working， which tested by power sensor and displacement sensor especially， is changed into electric voltage and electric pulse numerical signals. And these signals can be tested by A/D and counted by LS7266R1. Finally the test of the material properties can be controlled by itself， or controlled by the COM command of PC.
上传时间： 2013-11-02
上传用户：yl1140vista
主要介绍了以PIC18F2480单片机为处理器，基于可编程多路开关检测接口器件MC33993实现的车用多路开关检测接口电路的设计。该设计克服了以往基于分立元件的检测接口电路的弊端，简化了接口电路设计，保证了车用开关工作的可靠性和安全性。 Abstract: The design of automotive multiple switch detection interface circuit based on MC33993 is introduced mainly which adopts PIC18F2480 single chip microprocessor.This circuit overcomes shortage of traditional design which contains many schism elements, and the application of MC33993 also predigests the whole design of interface circuit and guarantees the dependability and security of the switch.
上传时间： 2013-11-19
上传用户：star_in_rain
在研究车内有害气体成份的基础上，设计了一个基于PICl6F877A的车内有害气体检测控制系统。对该系统的控制方案、电源电路、复位电路、振荡电路、传感器检测电路、车窗控制电路、语音控制电路和相应的控制软件进行了设计。试验表明，该系统能有效检测车内确定的有害气体成份，并能对车内有害气体浓度进行有效调节，可改善车内空气质量。
上传时间： 2013-11-05
上传用户：lijinchuan
根据大坝变形监测的实际需求,以C8051F410为硬件控制平台,采用先进的CCD技术,设计了用于大坝水平位移监测的具有高精度自动测量功能的引张线仪.重点阐述了检测仪器的工作原理、硬件整体实现方案及软件设计流程.测量结果表明该仪器具有很强的实用性.
上传时间： 2013-11-06
上传用户：wudu0932
摘要：介绍了磁致伸缩位移传感器的结构、工作原理及信号特点，利用单片机对位移进行精确的测量，并对磁致伸缩位移传感器的输出模拟信号进行数字化处理，得到准确的数字信号，使得磁致伸缩位移传感器操作简单、互换性好、有效传递数据距离长。关键词：磁致伸缩；传感器；单片机；数字化；位移
上传时间： 2014-01-23
上传用户：拢共湖塘
