S3010舵机技术参数
上传时间： 2013-11-20
上传用户：comer1123
G0606M-I光电二极管 中文数据手册
上传时间： 2013-10-15
上传用户：firstbyte
根据通信协议完成了主机和水质传感器之间通信，并对读取到的数据处理后利用MSChart控件实时显示，从而达到水质参数实时显示和实时监控。通过与随机采集处理软件实验比对表明，采集处理结果正确，达到了实时采集监控的目标。
标签： Levelogger Solinst 3001 参数采集
上传时间： 2013-10-30
上传用户：破晓sunshine
多远程二极管温度传感器-Design Considerations for pc thermal management Multiple RDTS (remote diode temperature sensing) provides the most accurate method of sensing an IC’s junction temperature. It overcomes thermal gradient and placement issues encountered when trying to place external sensors. PCB component count decreases when using a device that provides multiple inputs.Better temperature sensing improves product performance and reliability. Disk drive data integrity suffers at elevated temperatures. IBM published an article stating that a 5°C rise in operating temperature causes a 15% increase in the drive’s failure rate. The overall performance of a system can be improved by providing a more accurate temperature measurement of the most critical devices allowing them to run just a few degrees hotter.The LM83 directly senses its own temperature and the temperature of three external PN junctions. One is dedicated to the CPU of choice, the other two go to other parts of your system that need thermal monitoring such as the disk drive or graphics chip. The SMBus-compatible LM83 supports SMBus timeout and logic levels. The LM83 has two interrupt outputs; one for user-programmable limits and WATCHDOG capability (INT), the other is a Critical Temperature Alarm output (T_CRIT_A) for system power supply shutdown.
标签： Considerat Design 远程 二极管
上传时间： 2014-12-21
上传用户：ljd123456
该系统采用自校正控制原理和常规PID控制相结合的算法!能快速整定出PID控制器的参数
上传时间： 2013-10-21
上传用户：Shaikh
无线模块参数介绍
上传时间： 2013-11-15
上传用户：tfyt
用二端口S-参数来表征差分电路的特性■ Sam Belkin差分电路结构因其更好的增益，二阶线性度，突出的抗杂散响应以及抗躁声性能而越来越多地被人们采用。这种电路结构通常需要一个与单端电路相连接的界面，而这个界面常常是采用“巴伦”器件（Balun），这种巴伦器件提供了平衡结构-到-不平衡结构的转换功能。要通过直接测量的方式来表征平衡电路特性的话，通常需要使用昂贵的四端口矢量网络分析仪。射频应用工程师还需要确定幅值和相位的不平衡是如何影响差分电路性能的。遗憾的是，在射频技术文献中，很难找到一种能表征电路特性以及衡量不平衡结构所产生影响的好的评估方法。这篇文章的目的就是要帮助射频应用工程师们通过使用常规的单端二端口矢量网络分析仪来准确可靠地解决作为他们日常工作的差分电路特性的测量问题。本文介绍了一些用来表征差分电路特性的实用和有效的方法， 特别是差分电压，共模抑制（CMRR），插入损耗以及基于二端口S-参数的差分阻抗。差分和共模信号在差分电路中有两种主要的信号类型：差分模式或差分电压Vdiff 和共模电压Vcm（见图2）。它们各自的定义如下[1]：• 差分信号是施加在平衡的3 端子系统中未接地的两个端子之上的• 共模信号是相等地施加在平衡放大器或其它差分器件的未接地的端子之上。
上传时间： 2013-10-14
上传用户：叶山豪
Agilent AN 154 S-Parameter Design Application Note S参数的设计与应用 The need for new high-frequency, solid-state circuitdesign techniques has been recognized both by microwaveengineers and circuit designers. These engineersare being asked to design solid state circuitsthat will operate at higher and higher frequencies.The development of microwave transistors andAgilent Technologies’ network analysis instrumentationsystems that permit complete network characterizationin the microwave frequency rangehave greatly assisted these engineers in their work.The Agilent Microwave Division’s lab staff hasdeveloped a high frequency circuit design seminarto assist their counterparts in R&D labs throughoutthe world. This seminar has been presentedin a number of locations in the United States andEurope.From the experience gained in presenting this originalseminar, we have developed a four-part videotape, S-Parameter Design Seminar. While the technologyof high frequency circuit design is everchanging, the concepts upon which this technologyhas been built are relatively invariant.The content of the S-Parameter Design Seminar isas follows:
标签： S参数
上传时间： 2013-12-19
上传用户：aa54
s参数计算器,S11,S12,S22,S21的参数，一算变知，非常方便。
上传时间： 2013-11-21
上传用户：432234
SM321中速贴片机参数
上传时间： 2013-12-08
上传用户：sunshine1402
