搜索：CNC-BRIDGE - 虫虫下载站

USB编程  UART to USB Bridge CKT.

UART to USB Bridge CKT.

https://www.eeworm.com/dl/643/426173.html

下载: 76

查看: 1041

文件格式  This is a PCI to USB bridge schematic that i was draw by hand from a PCI to USB card, the schematic

This is a PCI to USB bridge schematic that i was draw by hand from a PCI to USB card, the schematic use VT6212L to make bridge, the idear is that we can use microcontroler interface to PC through PCI slot by USB, ha ha it is too easy.

https://www.eeworm.com/dl/639/426632.html

下载: 51

查看: 1057

VxWorks Bridge PNE 3.3 source code, running at more than vxworks6.x version.

Bridge PNE 3.3 source code, running at more than vxworks6.x version.

https://www.eeworm.com/dl/662/440043.html

下载: 164

查看: 1042

其他行业  control step motor (use for CNC machine), use chip dspic30f4011, include interpolation

control step motor (use for CNC machine), use chip dspic30f4011, include interpolation

https://www.eeworm.com/dl/668/445443.html

下载: 115

查看: 1153

通讯/手机编程  Wishbone to LPC (Low-Pin Count) Bridge, includes master and slave modules. Supports 8-bit I/O Read a

Wishbone to LPC (Low-Pin Count) Bridge, includes master and slave modules. Supports 8-bit I/O Read and Write cycles, 8-bit Memory Read/Write cycles, DMA cycles, and up to 32-bit Firmware memory read/write cycles. Serial IRQ support is also provided. None of this has been tested (yet) with a third-p ...

https://www.eeworm.com/dl/527/457359.html

下载: 33

查看: 1101

VHDL/FPGA/Verilog This is is a bridge IP core to interface the Tensilica PIF bus protocol with the OpenCores WishBone.

This is is a bridge IP core to interface the Tensilica PIF bus protocol with the OpenCores WishBone. It currently supports single-cycle as well as burst transfer operations. The core has been tested in a master-PIF slave-WB configuration.

https://www.eeworm.com/dl/663/457520.html

下载: 179

查看: 1100

嵌入式/单片机编程  Cypress公司开发的2.4G无线键盘鼠标及其Bridge源代码

Cypress公司开发的2.4G无线键盘鼠标及其Bridge源代码，对于开发无线鼠标键盘的人来说是很好的参考例子！

https://www.eeworm.com/dl/647/466864.html

下载: 78

查看: 1047

其他行业  老外用VB写的CNC仿真程序源码

老外用VB写的CNC仿真程序源码，可以载入G Code，还有OpenGL的3D图

https://www.eeworm.com/dl/668/468278.html

下载: 194

查看: 1113

单片机开发  NS-CNC步进电机驱动器.................

NS-CNC步进电机驱动器.................

https://www.eeworm.com/dl/648/474485.html

下载: 49

查看: 1033

微处理器开发  userial is an Free project building an USB to I2C/SPI/GPIO bridge, using the Atmel AT90USB647 chip.

userial is an Free project building an USB to I2C/SPI/GPIO bridge, using the Atmel AT90USB647 chip. Hardware and Software are released under an Open Source licence. It supports the following interfaces: * USB interface (serial emulation) * JTAG * I2C (TWI) * SPI * 8 General purp ...

https://www.eeworm.com/dl/655/486189.html

下载: 143

查看: 1066

搜索结果