📄 door_control.pin
字号:
-- Copyright (C) 1991-2004 Altera Corporation
-- Any megafunction design, and related netlist (encrypted or decrypted),
-- support information, device programming or simulation file, and any other
-- associated documentation or information provided by Altera or a partner
-- under Altera's Megafunction Partnership Program may be used only
-- to program PLD devices (but not masked PLD devices) from Altera. Any
-- other use of such megafunction design, netlist, support information,
-- device programming or simulation file, or any other related documentation
-- or information is prohibited for any other purpose, including, but not
-- limited to modification, reverse engineering, de-compiling, or use with
-- any other silicon devices, unless such use is explicitly licensed under
-- a separate agreement with Altera or a megafunction partner. Title to the
-- intellectual property, including patents, copyrights, trademarks, trade
-- secrets, or maskworks, embodied in any such megafunction design, netlist,
-- support information, device programming or simulation file, or any other
-- related documentation or information provided by Altera or a megafunction
-- partner, remains with Altera, the megafunction partner, or their respective
-- licensors. No other licenses, including any licenses needed under any third
-- party's intellectual property, are provided herein.
--
-- This is a Quartus II output file. It is for reporting purposes only, and is
-- not intended for use as a Quartus II input file. This file cannot be used
-- to make Quartus II pin assignments - for instructions on how to make pin
-- assignments, please see Quartus II help.
---------------------------------------------------------------------------------
---------------------------------------------------------------------------------
-- NC : No Connect. This pin has no internal connection to the device.
-- VCC : Dedicated power pin, which MUST be connected to VCC.
-- VCCIO : Dedicated power pin, which MUST be connected to VCC
-- of its bank.
-- GND : Dedicated ground pin. Dedicated GND pins MUST be connected to GND.
-- It can also be used to report unused dedicated pins. The connection
-- on the board for unused dedicated pins depends on whether this will
-- be used in a future design. One example is device migration. When
-- using device migration, refer to the device pin-tables. If it is a
-- GND pin in the pin table or if it will not be used in a future design
-- for another purpose the it MUST be connected to GND. If it is an unused
-- dedicated pin, then it can be connected to a valid signal on the board
-- (low, high, or toggling) if that signal is required for a different
-- revision of the design.
-- GND+ : Unused input pin. It can also be used to report unused dual-purpose pins.
-- This pin should be connected to GND. It may also be connected to a
-- valid signal on the board (low, high, or toggling) if that signal
-- is required for a different revision of the design.
-- GND* : Unused I/O pin. This pin can either be left unconnected or
-- connected to GND. Connecting this pin to GND will improve the
-- device's immunity to noise.
-- RESERVED : Unused I/O pin, which MUST be left unconnected.
-- RESERVED_INPUT : Pin is tri-stated and should be connected to the board.
-- NON_MIGRATABLE: This pin cannot be migrated.
---------------------------------------------------------------------------------
Quartus II Version 4.2 Build 157 12/07/2004 SJ Full Version
CHIP "Door_Control" ASSIGNED TO AN: EPM7160SLC84-6
Pin Name/Usage : Location : Dir. : I/O Standard : Voltage : I/O Bank : User Assignment
-------------------------------------------------------------------------------------------------------------
GND+ : 1 : : : : :
GND+ : 2 : : : : :
VCCINT : 3 : power : : 5.0V : :
RESERVED : 4 : : : : :
RESERVED : 5 : : : : :
NC : 6 : : : : :
GND : 7 : gnd : : : :
RESERVED : 8 : : : : :
RESERVED : 9 : : : : :
RESERVED : 10 : : : : :
Door_on_off : 11 : output : TTL : : : N
Delay_Request : 12 : input : TTL : : : N
VCCIO : 13 : power : : 5.0V : :
TDI : 14 : input : TTL : : : N
RESERVED : 15 : : : : :
RESERVED : 16 : : : : :
RESERVED : 17 : : : : :
RESERVED : 18 : : : : :
GND : 19 : gnd : : : :
RESERVED : 20 : : : : :
RESERVED : 21 : : : : :
RESERVED : 22 : : : : :
TMS : 23 : input : TTL : : : N
RESERVED : 24 : : : : :
RESERVED : 25 : : : : :
VCCIO : 26 : power : : 5.0V : :
RESERVED : 27 : : : : :
RESERVED : 28 : : : : :
RESERVED : 29 : : : : :
RESERVED : 30 : : : : :
RESERVED : 31 : : : : :
GND : 32 : gnd : : : :
RESERVED : 33 : : : : :
En : 34 : input : TTL : : : N
RESERVED : 35 : : : : :
RESERVED : 36 : : : : :
RESERVED : 37 : : : : :
VCCIO : 38 : power : : 5.0V : :
NC : 39 : : : : :
RESERVED : 40 : : : : :
RESERVED : 41 : : : : :
GND : 42 : gnd : : : :
VCCINT : 43 : power : : 5.0V : :
RESERVED : 44 : : : : :
RESERVED : 45 : : : : :
NC : 46 : : : : :
GND : 47 : gnd : : : :
RESERVED : 48 : : : : :
RESERVED : 49 : : : : :
RESERVED : 50 : : : : :
Reset : 51 : input : TTL : : : N
RESERVED : 52 : : : : :
VCCIO : 53 : power : : 5.0V : :
RESERVED : 54 : : : : :
RESERVED : 55 : : : : :
RESERVED : 56 : : : : :
RESERVED : 57 : : : : :
Floor_Arrive : 58 : input : TTL : : : N
GND : 59 : gnd : : : :
RESERVED : 60 : : : : :
RESERVED : 61 : : : : :
TCK : 62 : input : TTL : : : N
RESERVED : 63 : : : : :
RESERVED : 64 : : : : :
RESERVED : 65 : : : : :
VCCIO : 66 : power : : 5.0V : :
RESERVED : 67 : : : : :
RESERVED : 68 : : : : :
RESERVED : 69 : : : : :
RESERVED : 70 : : : : :
TDO : 71 : output : TTL : : : N
GND : 72 : gnd : : : :
Ahead_Request : 73 : input : TTL : : : N
RESERVED : 74 : : : : :
RESERVED : 75 : : : : :
RESERVED : 76 : : : : :
RESERVED : 77 : : : : :
VCCIO : 78 : power : : 5.0V : :
NC : 79 : : : : :
RESERVED : 80 : : : : :
Slave_Request_Arrive : 81 : input : TTL : : : N
GND : 82 : gnd : : : :
Clock_1Hz : 83 : input : TTL : : : N
GND+ : 84 : : : : :
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -