testbackup.acf

ISA板卡

--
--  Copyright (C) 1988-2001 Altera Corporation
--  Any megafunction design, and related net list (encrypted or decrypted),
--  support information, device programming or simulation file, and any other
--  associated documentation or information provided by Altera or a partner
--  under Altera's Megafunction Partnership Program may be used only to
--  program PLD devices (but not masked PLD devices) from Altera.  Any other
--  use of such megafunction design, net list, support information, device
--  programming or simulation file, or any other related documentation or
--  information is prohibited for any other purpose, including, but not
--  limited to modification, reverse engineering, de-compiling, or use with
--  any other silicon devices, unless such use is explicitly licensed under
--  a separate agreement with Altera or a megafunction partner.  Title to
--  the intellectual property, including patents, copyrights, trademarks,
--  trade secrets, or maskworks, embodied in any such megafunction design,
--  net list, support information, device programming or simulation file, or
--  any other related documentation or information provided by Altera or a
--  megafunction partner, remains with Altera, the megafunction partner, or
--  their respective licensors.  No other licenses, including any licenses
--  needed under any third party's intellectual property, are provided herein.
--
CHIP testbackup
BEGIN
	|test1 :	OUTPUT_PIN = 74;
	|FRE-BACK :	INPUT_PIN = 77;
	|SBHE :	INPUT_PIN = 10;
	|CC :	OUTPUT_PIN = 74;
	|test :	OUTPUT_PIN = 76;
	|SPEEDIN :	INPUT_PIN = 77;
	|PB7A :	OUTPUT_PIN = 64;
	|PB5A :	OUTPUT_PIN = 65;
	|CLK60M :	INPUT_PIN = 4;
	|D15 :	INPUT_PIN = 12;
	|D14 :	INPUT_PIN = 15;
	|D13 :	INPUT_PIN = 16;
	|D12 :	INPUT_PIN = 17;
	|D11 :	INPUT_PIN = 18;
	|D10 :	INPUT_PIN = 20;
	|D9 :	INPUT_PIN = 21;
	|D8 :	INPUT_PIN = 22;
	|GCLK1 :	INPUT_PIN = 2;
	|RESET :	INPUT_PIN = 1;
	|/IOCS16 :	OUTPUT_PIN = 11;
	|D4 :	BIDIR_PIN = 69;
	|D3 :	BIDIR_PIN = 68;
	|D2 :	BIDIR_PIN = 60;
	|D1 :	BIDIR_PIN = 61;
	|D0 :	BIDIR_PIN = 67;
	DEVICE = EPM7160SLC84-10;
	|CK0 :	OUTPUT_PIN = 75;
	|GCLK :	INPUT_PIN = 83;
	|D7 :	BIDIR_PIN = 54;
	|D6 :	BIDIR_PIN = 55;
	|D5 :	BIDIR_PIN = 56;
	|WR/ :	INPUT_PIN = 52;
	|RD/ :	INPUT_PIN = 51;
	|AEN :	INPUT_PIN = 50;
	|A19 :	INPUT_PIN = 49;
	|A18 :	INPUT_PIN = 48;
	|A17 :	INPUT_PIN = 8;
	|A16 :	INPUT_PIN = 45;
	|A15 :	INPUT_PIN = 44;
	|A14 :	INPUT_PIN = 41;
	|A13 :	INPUT_PIN = 40;
	|A12 :	INPUT_PIN = 9;
	|A11 :	INPUT_PIN = 37;
	|A10 :	INPUT_PIN = 36;
	|A9 :	INPUT_PIN = 35;
	|A8 :	INPUT_PIN = 34;
	|A7 :	INPUT_PIN = 33;
	|A6 :	INPUT_PIN = 31;
	|A5 :	INPUT_PIN = 30;
	|A4 :	INPUT_PIN = 29;
	|A3 :	INPUT_PIN = 28;
	|A2 :	INPUT_PIN = 27;
	|A1 :	INPUT_PIN = 25;
	|A0 :	INPUT_PIN = 24;
END;

DEFAULT_DEVICES
BEGIN
	AUTO_DEVICE = EPM7256SQC208-7;
	AUTO_DEVICE = EPM7256SRC208-7;
	AUTO_DEVICE = EPM7192SQC160-7;
	AUTO_DEVICE = EPM7160SQC160-6;
	AUTO_DEVICE = EPM7160STC100-6;
	AUTO_DEVICE = EPM7160SLC84-6;
	AUTO_DEVICE = EPM7128SQC160-6;
	AUTO_DEVICE = EPM7128STC100-6;
	AUTO_DEVICE = EPM7128SQC100-6;
	AUTO_DEVICE = EPM7128SLC84-6;
	AUTO_DEVICE = EPM7064STC100-5;
	AUTO_DEVICE = EPM7064SLC84-5;
	AUTO_DEVICE = EPM7064STC44-5;
	AUTO_DEVICE = EPM7064SLC44-5;
	AUTO_DEVICE = EPM7032STC44-5;
	AUTO_DEVICE = EPM7032SLC44-5;
	ASK_BEFORE_ADDING_EXTRA_DEVICES = ON;
END;

TIMING_POINT
BEGIN
	DEVICE_FOR_TIMING_SYNTHESIS = EPM7160SLC84-10;
	CUT_ALL_BIDIR = ON;
	CUT_ALL_CLEAR_PRESET = ON;
	MAINTAIN_STABLE_SYNTHESIS = OFF;
END;

IGNORED_ASSIGNMENTS
BEGIN
	IGNORE_CLIQUE_ASSIGNMENTS = OFF;
	IGNORE_LOGIC_OPTION_ASSIGNMENTS = OFF;
	IGNORE_TIMING_ASSIGNMENTS = OFF;
	IGNORE_CHIP_ASSIGNMENTS = OFF;
	IGNORE_PIN_ASSIGNMENTS = OFF;
	IGNORE_LC_ASSIGNMENTS = OFF;
	IGNORE_DEVICE_ASSIGNMENTS = OFF;
	IGNORE_LOCAL_ROUTING_ASSIGNMENTS = OFF;
	DEMOTE_SPECIFIC_LCELL_ASSIGNMENTS_TO_LAB_ASSIGNMENTS = OFF;
	FIT_IGNORE_TIMING = ON;
END;

LOGIC_OPTIONS
BEGIN
	|CK0 :	ENABLE_PULLUP_RESISTOR = ON;
	|CK0 :	SLOW_SLEW_RATE = ON;
	|FRE-BACK :	ENABLE_PULLUP_RESISTOR = ON;
	|FRE-BACK :	SLOW_SLEW_RATE = ON;
	|SBHE :	ENABLE_PULLUP_RESISTOR = ON;
	|D15 :	ENABLE_PULLUP_RESISTOR = ON;
	|D14 :	ENABLE_PULLUP_RESISTOR = ON;
	|D13 :	ENABLE_PULLUP_RESISTOR = ON;
	|D12 :	ENABLE_PULLUP_RESISTOR = ON;
	|D11 :	ENABLE_PULLUP_RESISTOR = ON;
	|D10 :	ENABLE_PULLUP_RESISTOR = ON;
	|D9 :	ENABLE_PULLUP_RESISTOR = ON;
	|D8 :	ENABLE_PULLUP_RESISTOR = ON;
	|RESET :	ENABLE_PULLUP_RESISTOR = ON;
	|CLK60M :	ENABLE_PULLUP_RESISTOR = ON;
	|CLK60M :	SLOW_SLEW_RATE = ON;
	|WR/ :	ENABLE_PULLUP_RESISTOR = ON;
	|RD/ :	ENABLE_PULLUP_RESISTOR = ON;
	|AEN :	ENABLE_PULLUP_RESISTOR = ON;
	|A19 :	ENABLE_PULLUP_RESISTOR = ON;
	|A18 :	ENABLE_PULLUP_RESISTOR = ON;
	|A17 :	ENABLE_PULLUP_RESISTOR = ON;
	|A16 :	ENABLE_PULLUP_RESISTOR = ON;
	|A15 :	ENABLE_PULLUP_RESISTOR = ON;
	|A14 :	ENABLE_PULLUP_RESISTOR = ON;
	|A13 :	ENABLE_PULLUP_RESISTOR = ON;
	|A12 :	ENABLE_PULLUP_RESISTOR = ON;
	|A11 :	ENABLE_PULLUP_RESISTOR = ON;
	|A10 :	ENABLE_PULLUP_RESISTOR = ON;
	|A9 :	ENABLE_PULLUP_RESISTOR = ON;
	|A8 :	ENABLE_PULLUP_RESISTOR = ON;
	|A7 :	ENABLE_PULLUP_RESISTOR = ON;
	|A6 :	ENABLE_PULLUP_RESISTOR = ON;
	|A5 :	ENABLE_PULLUP_RESISTOR = ON;
	|A4 :	ENABLE_PULLUP_RESISTOR = ON;
	|A3 :	ENABLE_PULLUP_RESISTOR = ON;
	|A2 :	ENABLE_PULLUP_RESISTOR = ON;
	|A1 :	ENABLE_PULLUP_RESISTOR = ON;
	|A0 :	ENABLE_PULLUP_RESISTOR = ON;
	|GCLK1 :	ENABLE_PULLUP_RESISTOR = ON;
	|GCLK1 :	TURBO_BIT = ON;
	|GCLK1 :	SLOW_SLEW_RATE = ON;
	"|count24:831" :	TURBO_BIT = ON;
	|SPEEDIN :	TURBO_BIT = ON;
	|SPEEDIN :	ENABLE_PULLUP_RESISTOR = ON;
	|PB5A :	POWER_UP_HIGH = ON;
	|PB7A :	POWER_UP_HIGH = ON;
	|CLK60M :	TURBO_BIT = ON;
	"|:785" :	IO_STANDARD = 1.8V;
	"|:786" :	IO_STANDARD = 1.8V;
	"|count-16t:747" :	IO_STANDARD = 1.8V;
	"|:785" :	TURBO_BIT = ON;
	"|:786" :	TURBO_BIT = ON;
	"|:786" :	SLOW_SLEW_RATE = OFF;
	|TEST :	SLOW_SLEW_RATE = OFF;
	"|:744" :	TURBO_BIT = ON;
	"|:744" :	SLOW_SLEW_RATE = OFF;
	"|:756" :	TURBO_BIT = ON;
	"|:756" :	SLOW_SLEW_RATE = OFF;
	"|:752" :	TURBO_BIT = ON;
	"|:752" :	SLOW_SLEW_RATE = OFF;
	"|count-16t:747" :	ENABLE_PULLUP_RESISTOR = OFF;
	"|count-16t:747" :	INCREASE_INPUT_DELAY = OFF;
	"|count-16t:747" :	IGNORE_SOFT_BUFFERS = ON;
	|CK0 :	TURBO_BIT = ON;
	"|:269" :	IO_STANDARD = LVTTL;
	"|:269" :	TURBO_BIT = ON;
	"|:269" :	SLOW_SLEW_RATE = OFF;
	"|:268" :	IO_STANDARD = LVTTL;
	"|:268" :	FAST_IO = ON;
	"|:268" :	TURBO_BIT = ON;
	"|:268" :	SLOW_SLEW_RATE = OFF;
	"|count-16t:747" :	INSERT_ADDITIONAL_LOGIC_CELL = OFF;
	|GCLK :	IO_STANDARD = LVTTL;
	"|count-16t:747" :	TURBO_BIT = ON;
	"|count-16t:747" :	SLOW_SLEW_RATE = OFF;
	|GCLK :	SLOW_SLEW_RATE = OFF;
	|GCLK :	FAST_IO = ON;
	|GCLK :	TURBO_BIT = ON;
	|GCLK :	XOR_SYNTHESIS = ON;
	|GCLK :	ENABLE_PULLUP_RESISTOR = ON;
	|D7 :	ENABLE_PULLUP_RESISTOR = ON;
	|D6 :	ENABLE_PULLUP_RESISTOR = ON;
	|D5 :	ENABLE_PULLUP_RESISTOR = ON;
	|D4 :	ENABLE_PULLUP_RESISTOR = ON;
	|D3 :	ENABLE_PULLUP_RESISTOR = ON;
	|D2 :	ENABLE_PULLUP_RESISTOR = ON;
	|D1 :	ENABLE_PULLUP_RESISTOR = ON;
	|D0 :	ENABLE_PULLUP_RESISTOR = ON;
END;

GLOBAL_PROJECT_DEVICE_OPTIONS
BEGIN
	RESERVED_LCELLS_PERCENT = 0;
	RESERVED_PINS_PERCENT = 0;
	SECURITY_BIT = OFF;
	USER_CLOCK = OFF;
	AUTO_RESTART = OFF;
	RELEASE_CLEARS = OFF;
	ENABLE_DCLK_OUTPUT = OFF;
	DISABLE_TIME_OUT = OFF;
	CONFIG_SCHEME = ACTIVE_SERIAL;
	FLEX8000_ENABLE_JTAG = OFF;
	DATA0 = RESERVED_TRI_STATED;
	DATA1_TO_DATA7 = UNRESERVED;
	nWS_nRS_nCS_CS = UNRESERVED;
	RDYnBUSY = UNRESERVED;
	RDCLK = UNRESERVED;
	SDOUT = RESERVED_DRIVES_OUT;
	ADD0_TO_ADD12 = UNRESERVED;
	ADD13 = UNRESERVED;
	ADD14 = UNRESERVED;
	ADD15 = UNRESERVED;
	ADD16 = UNRESERVED;
	ADD17 = UNRESERVED;
	CLKUSR = UNRESERVED;
	nCEO = UNRESERVED;
	ENABLE_CHIP_WIDE_RESET = OFF;
	ENABLE_CHIP_WIDE_OE = OFF;
	ENABLE_INIT_DONE_OUTPUT = OFF;
	FLEX10K_JTAG_USER_CODE = 7F;
	CONFIG_SCHEME_10K = PASSIVE_SERIAL;
	MAX7000S_USER_CODE = FFFF;
	FLEX10K_ENABLE_LOCK_OUTPUT = OFF;
	MAX7000S_ENABLE_JTAG = ON;
	CONFIG_SCHEME_FLEX_6000 = PASSIVE_SERIAL;
	FLEX6000_ENABLE_JTAG = OFF;
	FLEX10K_USE_LOW_VOLTAGE_CONFIGURATION_EPROM = OFF;
	FLEX10KA_USE_LOW_VOLTAGE_CONFIGURATION_EPROM = ON;
	FLEX6000_USE_LOW_VOLTAGE_CONFIGURATION_EPROM = OFF;
	MAX7000AE_USER_CODE = FFFFFFFF;
	MAX7000AE_ENABLE_JTAG = ON;
	FLEX_CONFIGURATION_EPROM = AUTO;
	CONFIG_EPROM_USER_CODE = FFFFFFFF;
	CONFIG_EPROM_PULLUP_RESISTOR = ON;
	MAX7000B_VCCIO_IOBANK1 = 3.3V;
	MAX7000B_VCCIO_IOBANK2 = 3.3V;
	MAX7000B_ENABLE_VREFA = OFF;
	MAX7000B_ENABLE_VREFB = OFF;
	MULTIVOLT_IO = ON;
END;

GLOBAL_PROJECT_SYNTHESIS_ASSIGNMENT_OPTIONS
BEGIN
	AUTO_GLOBAL_OE = OFF;
	AUTO_GLOBAL_PRESET = OFF;
	AUTO_GLOBAL_CLEAR = OFF;
	AUTO_GLOBAL_CLOCK = OFF;
	AUTO_REGISTER_PACKING = OFF;
	DEVICE_FAMILY = MAX7000S;
	OPTIMIZE_FOR_SPEED = 5;
	ONE_HOT_STATE_MACHINE_ENCODING = OFF;
	AUTO_IMPLEMENT_IN_EAB = OFF;
	STYLE = FAST;
	MULTI_LEVEL_SYNTHESIS_MAX5000_7000 = ON;
	AUTO_OPEN_DRAIN_PINS = ON;
	AUTO_FAST_IO = ON;
	MULTI_LEVEL_SYNTHESIS_MAX9000 = OFF;
END;

COMPILER_PROCESSING_CONFIGURATION
BEGIN
	FITTER_SETTINGS = NORMAL;
	TIMING_SNF_EXTRACTOR = OFF;
	USE_QUARTUS_FITTER = OFF;
	DESIGN_DOCTOR = OFF;
	DESIGN_DOCTOR_RULES = EPLD;
	FUNCTIONAL_SNF_EXTRACTOR = OFF;
	OPTIMIZE_TIMING_SNF = OFF;
	LINKED_SNF_EXTRACTOR = OFF;
	RPT_FILE_EQUATIONS = ON;
	RPT_FILE_HIERARCHY = ON;
	RPT_FILE_LCELL_INTERCONNECT = ON;
	RPT_FILE_USER_ASSIGNMENTS = ON;
	GENERATE_AHDL_TDO_FILE = OFF;
	SMART_RECOMPILE = OFF;
	PRESERVE_ALL_NODE_NAME_SYNONYMS = OFF;
END;

COMPILER_INTERFACES_CONFIGURATION
BEGIN
	EDIF_NETLIST_WRITER = OFF;
	EDIF_OUTPUT_VERSION = 200;
	XNF_EMULATE_TRI_STATE_BUSES = INTERNAL_LOGIC;
	XNF_TRANSLATE_INTERNAL_NODE_NAMES = ON;
	XNF_GENERATE_AHDL_TDX_FILE = ON;
	VERILOG_NETLIST_WRITER = OFF;
	VHDL_NETLIST_WRITER = OFF;
	USE_SYNOPSYS_SYNTHESIS = OFF;
	SYNOPSYS_COMPILER = DESIGN;
	SYNOPSYS_DESIGNWARE = OFF;
	SYNOPSYS_HIERARCHICAL_COMPILATION = ON;
	SYNOPSYS_BOUNDARY_OPTIMIZATION = OFF;
	SYNOPSYS_MAPPING_EFFORT = MEDIUM;
	VHDL_READER_VERSION = VHDL93;
	VHDL_WRITER_VERSION = VHDL93;
	VERILOG_OUTPUT_MAP_ILLEGAL_CHAR = OFF;
	VERILOG_TRUNCATE_HIERARCHY_PATH = OFF;
	VHDL_TRUNCATE_HIERARCHY_PATH = OFF;
	EDIF_TRUNCATE_HIERARCHY_PATH = OFF;
	VERILOG_FLATTEN_BUS = OFF;
	VHDL_FLATTEN_BUS = OFF;
	VERILOG_OUTPUT_DELAY_CONSTRUCTS = VO_FILE;
	VHDL_OUTPUT_DELAY_CONSTRUCTS = VHO_FILE;
	VHDL_GENERATE_CONFIGURATION_DECLARATION = OFF;
	EDIF_INPUT_LMF1 = *.lmf;
	EDIF_INPUT_LMF2 = *.lmf;
	EDIF_OUTPUT_EDC_FILE = *.edc;
	EDIF_INPUT_VCC = VCC;
	EDIF_INPUT_GND = GND;
	EDIF_OUTPUT_VCC = VCC;
	EDIF_OUTPUT_GND = GND;
	EDIF_INPUT_USE_LMF1 = OFF;
	EDIF_INPUT_USE_LMF2 = OFF;
	EDIF_OUTPUT_USE_EDC = OFF;
	EDIF_OUTPUT_DELAY_CONSTRUCTS = EDO_FILE;
	EDIF_OUTPUT_MAP_ILLEGAL_CHAR = OFF;
	EDIF_OUTPUT_INCLUDE_SPECIAL_PRIM = OFF;
	EDIF_OUTPUT_FORCE_0NS_DELAYS = OFF;
	EDIF_FLATTEN_BUS = OFF;
	EDIF_BUS_DELIMITERS = [];
	EDIF_INPUT_SHOW_LMF_MAPPING_MESSAGES = OFF;
	NETLIST_OUTPUT_TIME_SCALE = 0.1ns;
END;

CUSTOM_DESIGN_DOCTOR_RULES
BEGIN
	RIPPLE_CLOCKS = ON;
	GATED_CLOCKS = ON;
	MULTI_LEVEL_CLOCKS = ON;
	MULTI_CLOCK_NETWORKS = ON;
	STATIC_HAZARDS_BEFORE_SYNTHESIS = ON;
	STATIC_HAZARDS_AFTER_SYNTHESIS = OFF;
	PRESET_CLEAR_NETWORKS = ON;
	ASYNCHRONOUS_INPUTS = ON;
	DELAY_CHAINS = ON;