📄 transmitter.pin
字号:
-- Copyright (C) 1991-2006 Altera Corporation
-- Your use of Altera Corporation's design tools, logic functions
-- and other software and tools, and its AMPP partner logic
-- functions, and any output files any of the foregoing
-- (including device programming or simulation files), and any
-- associated documentation or information are expressly subject
-- to the terms and conditions of the Altera Program License
-- Subscription Agreement, Altera MegaCore Function License
-- Agreement, or other applicable license agreement, including,
-- without limitation, that your use is for the sole purpose of
-- programming logic devices manufactured by Altera and sold by
-- Altera or its authorized distributors. Please refer to the
-- applicable agreement for further details.
--
-- This is a Quartus II output file. It is for reporting purposes only, and is
-- not intended for use as a Quartus II input file. This file cannot be used
-- to make Quartus II pin assignments - for instructions on how to make pin
-- assignments, please see Quartus II help.
------------------------------------------------------------------------------
------------------------------------------------------------------------------
-- NC : No Connect. This pin has no internal connection to the device.
-- VCC_INT : Dedicated power pin, which MUST be connected to VCC (5.0V).
-- VCC_IO : Dedicated power pin, which MUST be connected to VCC (Refer to
-- the table below for voltage).
-- GND : Dedicated ground pin, which MUST be connected to GND.
-- GND+ : Unused input. This pin should be connected to GND. It may also
-- be connected to a valid signal on the board (low, high, or
-- toggling) if that signal is required for a different revision
-- of the design.
-- GND* : Unused I/O pin. This pin can either be left unconnected or
-- connected to GND. Connecting this pin to GND will improve the
-- device's immunity to noise.
-- RESERVED_INPUT : Pin is tri-stated and should be connected to the board.
------------------------------------------------------------------------------
Quartus II Version 6.0 Build 178 04/27/2006 SJ Full Version
CHIP "transmitter" ASSIGNED TO AN: EPF10K20TC144-4
Pin Name/Usage : Location : Dir. : I/O Standard : Voltage : I/O Bank : User Assignment
-------------------------------------------------------------------------------------------------------------
TCK : 1 : input : : : :
CONF_DONE : 2 : bidir : : : :
nCEO : 3 : output : : : :
TDO : 4 : output : : : :
VCC_IO : 5 : power : : 5.0V : :
VCC_INT : 6 : power : : 5.0V : :
RESERVED_INPUT : 7 : : : : :
osc : 8 : output : TTL : : : Y
send : 9 : output : TTL : : : Y
RESERVED_INPUT : 10 : : : : :
RESERVED_INPUT : 11 : : : : :
RESERVED_INPUT : 12 : : : : :
RESERVED_INPUT : 13 : : : : :
RESERVED_INPUT : 14 : : : : :
GND_IO : 15 : gnd : : : :
GND_INT : 16 : gnd : : : :
RESERVED_INPUT : 17 : : : : :
RESERVED_INPUT : 18 : : : : :
RESERVED_INPUT : 19 : : : : :
reset : 20 : input : TTL : : : Y
RESERVED_INPUT : 21 : : : : :
RESERVED_INPUT : 22 : : : : :
RESERVED_INPUT : 23 : : : : :
VCC_IO : 24 : power : : 5.0V : :
VCC_INT : 25 : power : : 5.0V : :
RESERVED_INPUT : 26 : : : : :
RESERVED_INPUT : 27 : : : : :
send_out[6] : 28 : output : TTL : : : Y
fre_set[0] : 29 : input : TTL : : : Y
fre_set[1] : 30 : input : TTL : : : Y
fre_set[2] : 31 : input : TTL : : : Y
fre_set[3] : 32 : input : TTL : : : Y
fre_set[4] : 33 : input : TTL : : : Y
TMS : 34 : input : : : :
nSTATUS : 35 : bidir : : : :
fre_set[5] : 36 : input : TTL : : : Y
SET_LED[0] : 37 : input : TTL : : : Y
SET_LED[1] : 38 : input : TTL : : : Y
send_out[5] : 39 : output : TTL : : : Y
GND_IO : 40 : gnd : : : :
send_out[4] : 41 : output : TTL : : : Y
send_out[3] : 42 : output : TTL : : : Y
send_out[2] : 43 : output : TTL : : : Y
send_out[1] : 44 : output : TTL : : : Y
VCC_IO : 45 : power : : 5.0V : :
send_out[0] : 46 : output : TTL : : : Y
RESERVED_INPUT : 47 : : : : :
RESERVED_INPUT : 48 : : : : :
RESERVED_INPUT : 49 : : : : :
GND_IO : 50 : gnd : : : :
RESERVED_INPUT : 51 : : : : :
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -