📄 de2_sd_card_audio.v
字号:
// --------------------------------------------------------------------
// Copyright (c) 2005 by Terasic Technologies Inc.
// --------------------------------------------------------------------
//
// Permission:
//
// Terasic grants permission to use and modify this code for use
// in synthesis for all Terasic Development Boards and Altera Development
// Kits made by Terasic. Other use of this code, including the selling
// ,duplication, or modification of any portion is strictly prohibited.
//
// Disclaimer:
//
// This VHDL/Verilog or C/C++ source code is intended as a design reference
// which illustrates how these types of functions can be implemented.
// It is the user's responsibility to verify their design for
// consistency and functionality through the use of formal
// verification methods. Terasic provides no warranty regarding the use
// or functionality of this code.
//
// --------------------------------------------------------------------
//
// Terasic Technologies Inc
// 356 Fu-Shin E. Rd Sec. 1. JhuBei City,
// HsinChu County, Taiwan
// 302
//
// web: http://www.terasic.com/
// email: support@terasic.com
//
// --------------------------------------------------------------------
//
// Major Functions: DE2 SD-Card Music-Player Reference Design
//
// --------------------------------------------------------------------
//
// Revision History :
// --------------------------------------------------------------------
// Ver :| Author :| Mod. Date :| Changes Made:
// V1.0 :| Johnny Chen :| 05/08/19 :| Initial Revision
// V1.1 :| Johnny Chen :| 05/11/16 :| Add to FLASH Address FL_ADDR[21:20]
// --------------------------------------------------------------------
module DE2_SD_Card_Audio
(
// Onboard Oscilator
OSC_27,
OSC_50,
// Push Button
KEY,
// DPDT Switch
DPDT_SW,
// 7-SEG Dispaly
HEX0,
HEX1,
HEX2,
HEX3,
HEX4,
HEX5,
HEX6,
HEX7,
// LED
LED_GREEN,
LED_RED,
// UART
UART_TXD,
UART_RXD,
// SDRAM Interface
DRAM_DQ, // 16 Bits
DRAM_ADDR, // 12 Bits
DRAM_LDQM,
DRAM_UDQM,
DRAM_WE_N,
DRAM_CAS_N,
DRAM_RAS_N,
DRAM_CS_N,
DRAM_BA_0,
DRAM_BA_1,
DRAM_CLK,
DRAM_CKE,
// Flash Interface
FL_DQ, // 8 Bits
FL_ADDR, // 22 Bits
FL_WE_N,
FL_RST_N,
FL_OE_N,
FL_CE_N,
// SRAM Interface
SRAM_DQ, // 16 Bits
SRAM_ADDR, // 18 Bits
SRAM_UB_N,
SRAM_LB_N,
SRAM_WE_N,
SRAM_CE_N,
SRAM_OE_N,
// ISP1362 Interface
OTG_DATA, // 16 Bits
OTG_ADDR, // 2 Bits
OTG_CS_N,
OTG_RD_N,
OTG_WR_N,
OTG_RST_N,
OTG_FSPEED, // USB Full Speed, 0 = Enable, Z = Disable
OTG_LSPEED, // USB Low Speed, 0 = Enable, Z = Disable
OTG_INT0,
OTG_INT1,
OTG_DREQ0,
OTG_DREQ1,
OTG_DACK0_N,
OTG_DACK1_N,
// Ethernet Interface
ENET_DATA,
ENET_CMD,
ENET_CS_N,
ENET_WR_N,
ENET_RD_N,
ENET_RST_N,
ENET_INT,
ENET_CLK,
// Audio
AUD_ADCLRCK, // Audio CODEC ADC LR Clock
AUD_ADCDAT, // Audio CODEC ADC Data
AUD_DACLRCK, // Audio CODEC DAC LR Clock
AUD_DACDAT, // Audio CODEC DAC Data
AUD_BCLK, // Audio CODEC Bit-Stream Clock
AUD_XCK, // Audio CODEC Chip Clock
// LCD Module 16X2
LCD_ON, // LCD ON/OFF
LCD_BLON, // LCD Back Light ON/OFF
LCD_RW,
LCD_EN,
LCD_RS,
LCD_DATA,
// SD_Card Interface
SD_DAT,
SD_DAT3,
SD_CMD,
SD_CLK,
// I2C
I2C_DATA,
I2C_CLK,
// PS2
PS2_DATA,
PS2_CLK,
// TV
TD_RESET
);
// On Board Oscilator
input OSC_27;
input OSC_50;
// Push Button
input [3:0] KEY;
// DPDT Switch
input [17:0] DPDT_SW;
// 7-SEG Dispaly
output [6:0] HEX0;
output [6:0] HEX1;
output [6:0] HEX2;
output [6:0] HEX3;
output [6:0] HEX4;
output [6:0] HEX5;
output [6:0] HEX6;
output [6:0] HEX7;
// LED
output [8:0] LED_GREEN;
output [17:0] LED_RED;
// UART
output UART_TXD;
input UART_RXD;
// SDRAM Interface
inout [15:0] DRAM_DQ; // 16 Bits
output [11:0] DRAM_ADDR; // 12 Bits
output DRAM_LDQM;
output DRAM_UDQM;
output DRAM_WE_N;
output DRAM_CAS_N;
output DRAM_RAS_N;
output DRAM_CS_N;
output DRAM_BA_0;
output DRAM_BA_1;
output DRAM_CLK;
output DRAM_CKE;
// Flash Interface
inout [7:0] FL_DQ; // 8 Bits
output [21:0] FL_ADDR; // 22 Bits
output FL_WE_N;
output FL_RST_N;
output FL_OE_N;
output FL_CE_N;
// SRAM Interface
inout [15:0] SRAM_DQ; // 16 Bits
output [17:0] SRAM_ADDR; // 18 Bits
output SRAM_UB_N;
output SRAM_LB_N;
output SRAM_WE_N;
output SRAM_CE_N;
output SRAM_OE_N;
// ISP1362 Interface
inout [15:0] OTG_DATA;
output [1:0] OTG_ADDR;
output OTG_WR_N;
output OTG_RD_N;
output OTG_CS_N;
output OTG_RST_N;
output OTG_FSPEED; // USB Full Speed, 0 = Enable, Z = Disable
output OTG_LSPEED; // USB Low Speed, 0 = Enable, Z = Disable
input OTG_INT0;
input OTG_INT1;
input OTG_DREQ0;
input OTG_DREQ1;
output OTG_DACK0_N;
output OTG_DACK1_N;
// Ethernet Interface
inout [15:0] ENET_DATA;
output ENET_CMD;
output ENET_CS_N;
output ENET_WR_N;
output ENET_RD_N;
output ENET_RST_N;
input ENET_INT;
output ENET_CLK;
// Audio
output/*inout*/ AUD_ADCLRCK; // Audio CODEC ADC LR Clock
input AUD_ADCDAT; // Audio CODEC ADC Data
output/*inout*/ AUD_DACLRCK; // Audio CODEC DAC LR Clock
output AUD_DACDAT; // Audio CODEC DAC Data
inout AUD_BCLK; // Audio CODEC Bit-Stream Clock
output AUD_XCK; // Audio CODEC Chip Clock
// LCD Module 16X2
inout [7:0] LCD_DATA;
output LCD_ON; // LCD ON/OFF
output LCD_BLON; // LCD Back Light ON/OFF
output LCD_RW;
output LCD_EN;
output LCD_RS;
// SD_Card Interface
inout SD_DAT;
inout SD_DAT3;
inout SD_CMD;
output SD_CLK;
// I2C
inout I2C_DATA;
inout I2C_CLK;
// PS2
input PS2_DATA;
input PS2_CLK;
// TV
output TD_RESET;
//////////////////////////////////////////////////////////
wire [31:0] mSEG7_HEX;
wire [15:0] DATA_to_OTG;
wire [15:0] DATA_to_SRAM;
// I2C
wire SCL_OE_N;
wire SDA_OE_N;
wire SCL;
wire SDA;
// CPU
wire CPU_RESET;
// Ethernet
reg ENET_CLK;
// Audio
wire AUD_CTRL_CLK;
wire AUD_FULL;
always@(posedge OSC_50) ENET_CLK=~ENET_CLK;
// 16*2 LCD Module
assign LCD_ON = 1'b1; // LCD ON
assign LCD_BLON = 1'b1; // LCD Back Light
assign FL_RST_N = 1'b1;
assign FL_ADDR[21:20] = 2'b00; // Fixed 1M-Byte FLASH
// I2C Tri-inout
assign I2C_CLK = SCL_OE_N ? 1'bz : SCL ;
assign I2C_DATA = SDA_OE_N ? 1'bz : SDA ;
// Set SD Card to SD Mode
assign SD_DAT3 = 1'b1;
// Bypress 27 MHz
assign TD_RESET = 1'b1;
// Audio
assign AUD_ADCLRCK = AUD_DACLRCK;
assign AUD_XCK = AUD_CTRL_CLK;
SDRAM_PLL PLL1 (.inclk0(OSC_50),.c0(DRAM_CLK));
AUDIO_PLL PLL2 (.inclk0(OSC_27),.c0(AUD_CTRL_CLK));
Reset_Delay rst (OSC_50,CPU_RESET);
nios_0 u0 (
// 1) global signals:
.clk(OSC_50),
.reset_n(CPU_RESET),
// the_lcd_16207_0
.LCD_E_from_the_lcd_16207_0(LCD_EN),
.LCD_RS_from_the_lcd_16207_0(LCD_RS),
.LCD_RW_from_the_lcd_16207_0(LCD_RW),
.LCD_data_to_and_from_the_lcd_16207_0(LCD_DATA),
// the_SEG7_Display
.oSEG0_from_the_SEG7_Display(HEX0),
.oSEG1_from_the_SEG7_Display(HEX1),
.oSEG2_from_the_SEG7_Display(HEX2),
.oSEG3_from_the_SEG7_Display(HEX3),
.oSEG4_from_the_SEG7_Display(HEX4),
.oSEG5_from_the_SEG7_Display(HEX5),
.oSEG6_from_the_SEG7_Display(HEX6),
.oSEG7_from_the_SEG7_Display(HEX7),
// the_ISP1362
.OTG_ADDR_from_the_ISP1362(OTG_ADDR),
.OTG_CS_N_from_the_ISP1362(OTG_CS_N),
.OTG_DACK0_N_from_the_ISP1362(OTG_DACK0_N),
.OTG_DACK1_N_from_the_ISP1362(OTG_DACK1_N),
.OTG_DATA_to_and_from_the_ISP1362(OTG_DATA),
.OTG_DREQ0_to_the_ISP1362(OTG_DREQ0),
.OTG_DREQ1_to_the_ISP1362(OTG_DREQ1),
.OTG_INT0_to_the_ISP1362(OTG_INT0),
.OTG_INT1_to_the_ISP1362(OTG_INT1),
.OTG_RD_N_from_the_ISP1362(OTG_RD_N),
.OTG_RST_N_from_the_ISP1362(OTG_RST_N),
.OTG_WR_N_from_the_ISP1362(OTG_WR_N),
.OTG_FSPEED_from_the_ISP1362(OTG_FSPEED),
.OTG_LSPEED_from_the_ISP1362(OTG_LSPEED),
.iFSPEED_to_the_ISP1362(1'bz),
.iLSPEED_to_the_ISP1362(1'bz),
// the_DM9000A
.ENET_CMD_from_the_DM9000A(ENET_CMD),
.ENET_CS_N_from_the_DM9000A(ENET_CS_N),
.ENET_DATA_to_and_from_the_DM9000A(ENET_DATA),
.ENET_INT_to_the_DM9000A(ENET_INT),
.ENET_RD_N_from_the_DM9000A(ENET_RD_N),
.ENET_RST_N_from_the_DM9000A(ENET_RST_N),
.ENET_WR_N_from_the_DM9000A(ENET_WR_N),
// the_AUD_FULL
.in_port_to_the_AUD_FULL(AUD_FULL),
// the_Audio_0
.iCLK_18_4_to_the_Audio_0(AUD_CTRL_CLK),
.oAUD_BCK_from_the_Audio_0(AUD_BCLK),
.oAUD_DATA_from_the_Audio_0(AUD_DACDAT),
.oAUD_LRCK_from_the_Audio_0(AUD_DACLRCK),
.oWR_FULL_from_the_Audio_0(AUD_FULL),
// the_led_green
.out_port_from_the_led_green(LED_GREEN),
// the_led_red
.out_port_from_the_led_red(LED_RED),
// the_switch_pio
.in_port_to_the_switch_pio(DPDT_SW),
// the_button_pio
.in_port_to_the_button_pio(KEY),
// the_SD_CLK
.out_port_from_the_SD_CLK(SD_CLK),
// the_SD_CMD
.bidir_port_to_and_from_the_SD_CMD(SD_CMD),
// the_SD_DAT
.bidir_port_to_and_from_the_SD_DAT(SD_DAT),
// the_sdram_0
.zs_addr_from_the_sdram_0(DRAM_ADDR),
.zs_ba_from_the_sdram_0({DRAM_BA_1,DRAM_BA_0}),
.zs_cas_n_from_the_sdram_0(DRAM_CAS_N),
.zs_cke_from_the_sdram_0(DRAM_CKE),
.zs_cs_n_from_the_sdram_0(DRAM_CS_N),
.zs_dq_to_and_from_the_sdram_0(DRAM_DQ),
.zs_dqm_from_the_sdram_0({DRAM_UDQM,DRAM_LDQM}),
.zs_ras_n_from_the_sdram_0(DRAM_RAS_N),
.zs_we_n_from_the_sdram_0(DRAM_WE_N),
// the_sram_0
.SRAM_ADDR_from_the_sram_0(SRAM_ADDR),
.SRAM_CE_N_from_the_sram_0(SRAM_CE_N),
.SRAM_DQ_to_and_from_the_sram_0(SRAM_DQ),
.SRAM_LB_N_from_the_sram_0(SRAM_LB_N),
.SRAM_OE_N_from_the_sram_0(SRAM_OE_N),
.SRAM_UB_N_from_the_sram_0(SRAM_UB_N),
.SRAM_WE_N_from_the_sram_0(SRAM_WE_N),
// the_tri_state_bridge_0_avalon_slave
.select_n_to_the_cfi_flash_0(FL_CE_N),
.tri_state_bridge_0_address(FL_ADDR),
.tri_state_bridge_0_data(FL_DQ),
.tri_state_bridge_0_readn(FL_OE_N),
.write_n_to_the_cfi_flash_0(FL_WE_N),
// the_I2C_0
.scl_pad_i_to_the_I2C_0(I2C_CLK),
.scl_pad_o_from_the_I2C_0(SCL),
.scl_padoen_o_from_the_I2C_0(SCL_OE_N),
.sda_pad_i_to_the_I2C_0(I2C_DATA),
.sda_pad_o_from_the_I2C_0(SDA),
.sda_padoen_o_from_the_I2C_0(SDA_OE_N),
// the_uart_0
.rxd_to_the_uart_0(UART_RXD),
.txd_from_the_uart_0(UART_TXD)
);
I2C_AV_Config u1 ( // Host Side
.iCLK(OSC_50),
.iRST_N(CPU_RESET),
// I2C Side
.I2C_SCLK(I2C_CLK),
.I2C_SDAT(I2C_DATA) );
endmodule ⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -