ddr_clk.csf

vhdl编写的一个完整工程

COMPILER_SETTINGS
{
	RUN_TIMING_ANALYSES = ON;
	MERGE_HEX_FILE = OFF;
	FOCUS_ENTITY_NAME = |DDR_CLK;
	FAMILY = Stratix;
	DPRAM_DUAL_PORT_MODE_OTHER_SIGNALS_EPXA1 = "DPRAM0 TO 1 DPRAM1 TO 2";
	DPRAM_32BIT_SINGLE_PORT_MODE_OTHER_SIGNALS_EPXA1 = "MEGALAB COLUMN 1";
	DPRAM_8BIT_16BIT_SINGLE_PORT_MODE_OTHER_SIGNALS_EPXA1 = "MEGALAB COLUMN 1";
	DPRAM_DUAL_PORT_MODE_OUTPUT_EPXA1 = "DPRAM0 TO 1 DPRAM1 TO 2";
	DPRAM_32BIT_SINGLE_PORT_MODE_OUTPUT_EPXA1 = "LOWER TO 1ESB UPPER TO 1";
	DPRAM_8BIT_16BIT_SINGLE_PORT_MODE_OUTPUT_EPXA1 = "MEGALAB COLUMN 1";
	DPRAM_DUAL_PORT_MODE_INPUT_EPXA1 = "DPRAM0 TO 1 DPRAM1 TO 2";
	DPRAM_32BIT_SINGLE_PORT_MODE_INPUT_EPXA1 = "MEGALAB COLUMN 1";
	DPRAM_8BIT_16BIT_SINGLE_PORT_MODE_INPUT_EPXA1 = "MEGALAB COLUMN 1";
	DPRAM_DUAL_PORT_MODE_OTHER_SIGNALS_EPXA4_10 = "DPRAM0 TO 3 DPRAM1 TO 4";
	DPRAM_SINGLE_PORT_MODE_OTHER_SIGNALS_EPXA4_10 = "DPRAM0 TO 3 DPRAM1 TO 4";
	DPRAM_WIDE_MODE_OTHER_SIGNALS_EPXA4_10 = "MEGALAB COLUMN 3";
	DPRAM_DEEP_MODE_OTHER_SIGNALS_EPXA4_10 = "MEGALAB COLUMN 3";
	DPRAM_DUAL_PORT_MODE_OUTPUT_EPXA4_10 = "DPRAM0 TO 3 DPRAM1 TO 4ESB";
	DPRAM_SINGLE_PORT_MODE_OUTPUT_EPXA4_10 = "DPRAM0 TO 3 DPRAM1 TO 4ESB";
	DPRAM_WIDE_MODE_OUTPUT_EPXA4_10 = "LOWER TO 3 UPPER TO 4ESB";
	DPRAM_DEEP_MODE_OUTPUT_EPXA4_10 = "MEGALAB COLUMN 3";
	DPRAM_DUAL_PORT_MODE_INPUT_EPXA4_10 = "DPRAM0 TO 3 DPRAM1 TO 4";
	DPRAM_SINGLE_PORT_MODE_INPUT_EPXA4_10 = "DPRAM0 TO 3 DPRAM1 TO 4";
	DPRAM_WIDE_MODE_INPUT_EPXA4_10 = "LOWER TO 3 UPPER TO 4";
	DPRAM_DEEP_MODE_INPUT_EPXA4_10 = "MEGALAB COLUMN 3";
	DPRAM_OTHER_SIGNALS_EPXA4_10 = "DEFAULT OTHER ROUTING OPTIONS";
	DPRAM_OUTPUT_EPXA4_10 = "DEFAULT OUTPUT ROUTING OPTIONS";
	DPRAM_INPUT_EPXA4_10 = "DEFAULT INPUT ROUTING OPTIONS";
	STRIPE_TO_PLD_INTERRUPTS_EPXA4_10 = "MEGALAB COLUMN 2";
	PLD_TO_STRIPE_INTERRUPTS_EPXA4_10 = "MEGALAB COLUMN 2";
	PROCESSOR_DEBUG_EXTENSIONS_EPXA4_10 = "MEGALAB COLUMN 2";
	STRIPE_TO_PLD_BRIDGE_EPXA4_10 = "MEGALAB COLUMN 1";
	FAST_FIT_COMPILATION = OFF;
	SIGNAL_PROBE_AUTO_ASSIGN = 0;
	SIGNAL_PROBE_COMPILATION = OFF;
	SIGNAL_PROBE_ROUTING = ALL_SIGNAL_PROBE;
	LOGICLOCK_FITTER_TYPE = OFF;
	OPTIMIZE_IOC_REGISTER_PLACEMENT_FOR_TIMING = ON;
	OPTIMIZE_TIMING = NORMAL_COMPILATION;
	COMPILATION_LEVEL = FULL;
	SAVE_DISK_SPACE = ON;
	SPEED_DISK_USAGE_TRADEOFF = NORMAL;
	LOGICLOCK_INCREMENTAL_COMPILE_ASSIGNMENT = OFF;
}
CHIP(DDR_CLK)
{
	e : IO_STANDARD = "DIFFERENTIAL SSTL-2";
	e0 : IO_STANDARD = "SSTL-2 CLASS I";
	fbin : IO_STANDARD = "SSTL-2 CLASS I";
	RESERVE_ALL_UNUSED_PINS = "AS OUTPUT DRIVING GROUND";
	HEXOUT_FILE_COUNT_DIRECTION = UP;
	HEXOUT_FILE_START_ADDRESS = 0;
	GENERATE_HEX_FILE = OFF;
	GENERATE_RBF_FILE = OFF;
	GENERATE_TTF_FILE = OFF;
	STRATIX_CRC_ERROR_CHECKING = OFF;
	RESERVE_DATA0_AFTER_CONFIGURATION = OFF;
	RESERVE_DATA7_THROUGH_DATA1_AFTER_CONFIGURATION = OFF;
	RESERVE_RDYNBUSY_AFTER_CONFIGURATION = OFF;
	RESERVE_NWS_NRS_NCS_CS_AFTER_CONFIGURATION = OFF;
	DISABLE_CONF_DONE_AND_NSTATUS_PULLUPS_ON_CONFIG_DEVICE = OFF;
	AUTO_INCREMENT_CONFIG_DEVICE_JTAG_USER_CODE = ON;
	EPROM_USE_CHECKSUM_AS_USERCODE = OFF;
	FLEX10K_CONFIG_DEVICE_JTAG_USER_CODE = FFFFFFFF;
	MERCURY_CONFIG_DEVICE_JTAG_USER_CODE = FFFFFFFF;
	APEX20K_CONFIG_DEVICE_JTAG_USER_CODE = FFFFFFFF;
	STRATIX_CONFIG_DEVICE_JTAG_USER_CODE = FFFFFFFF;
	STRATIX_CONFIGURATION_DEVICE = EPC2;
	FLEX10K_CONFIGURATION_DEVICE = EPC2;
	FLEX6K_CONFIGURATION_DEVICE = EPC1;
	MERCURY_CONFIGURATION_DEVICE = EPC2;
	EXCALIBUR_CONFIGURATION_DEVICE = EPC2;
	APEX20K_CONFIGURATION_DEVICE = EPC2;
	USE_CONFIGURATION_DEVICE = ON;
	ENABLE_INIT_DONE_OUTPUT = OFF;
	FLEX10K_ENABLE_LOCK_OUTPUT = OFF;
	ENABLE_DEVICE_WIDE_OE = OFF;
	ENABLE_DEVICE_WIDE_RESET = OFF;
	RELEASE_CLEARS_BEFORE_TRI_STATES = OFF;
	AUTO_RESTART_CONFIGURATION = OFF;
	ENABLE_VREFB_PIN = OFF;
	ENABLE_VREFA_PIN = OFF;
	SECURITY_BIT = OFF;
	USER_START_UP_CLOCK = OFF;
	APEX_II_CONFIGURATION_SCHEME = "PASSIVE SERIAL";
	FLEX10K_CONFIGURATION_SCHEME = "PASSIVE SERIAL";
	FLEX6K_CONFIGURATION_SCHEME = "PASSIVE SERIAL";
	MERCURY_CONFIGURATION_SCHEME = "PASSIVE SERIAL";
	EXCALIBUR_CONFIGURATION_SCHEME = "PASSIVE SERIAL";
	STRATIX_CONFIGURATION_SCHEME = "PASSIVE SERIAL";
	APEX20K_CONFIGURATION_SCHEME = "PASSIVE SERIAL";
	STRATIX_UPDATE_MODE = STANDARD;
	USE_CHECKSUM_AS_USERCODE = OFF;
	MAX7000_JTAG_USER_CODE = FFFFFFFF;
	FLEX10K_JTAG_USER_CODE = 7F;
	MERCURY_JTAG_USER_CODE = FFFFFFFF;
	APEX20K_JTAG_USER_CODE = FFFFFFFF;
	STRATIX_JTAG_USER_CODE = FFFFFFFF;
	RESERVE_NCEO_AFTER_CONFIGURATION = OFF;
	FLEX10K_ENABLE_LOW_VOLTAGE_MODE_ON_CONFIG_DEVICE = ON;
	FLEX6K_ENABLE_LOW_VOLTAGE_MODE_ON_CONFIG_DEVICE = OFF;
	MAX7000_ENABLE_JTAG_BST_SUPPORT = ON;
	ENABLE_JTAG_BST_SUPPORT = OFF;
	BASE_PIN_OUT_FILE_ON_SAMEFRAME_DEVICE = OFF;
	MAX7000_USE_CHECKSUM_AS_USERCODE = OFF;
	DEVICE = EP1S10F780C7;
}
AUTO_SLD_HUB_ENTITY
{
	AUTO_INSERT_SLD_HUB_ENTITY = ENABLE;
	HUB_INSTANCE_NAME = sld_hub_inst;
	HUB_ENTITY_NAME = sld_hub;
}
DEFAULT_DEVICE_OPTIONS
{
	RESERVE_PIN = "AS INPUT TRI-STATED";
	RESERVE_ALL_UNUSED_PINS = "AS OUTPUT DRIVING GROUND";
	HEXOUT_FILE_COUNT_DIRECTION = UP;
	HEXOUT_FILE_START_ADDRESS = 0;
	GENERATE_HEX_FILE = OFF;
	GENERATE_RBF_FILE = OFF;
	GENERATE_TTF_FILE = OFF;
	STRATIX_CRC_ERROR_CHECKING = OFF;
	RESERVE_RUNLU_AFTER_CONFIGURATION = OFF;
	RESERVE_DATA0_AFTER_CONFIGURATION = OFF;
	RESERVE_DATA7_THROUGH_DATA1_AFTER_CONFIGURATION = OFF;
	RESERVE_RDYNBUSY_AFTER_CONFIGURATION = OFF;
	RESERVE_NWS_NRS_NCS_CS_AFTER_CONFIGURATION = OFF;
	DISABLE_CONF_DONE_AND_NSTATUS_PULLUPS_ON_CONFIG_DEVICE = OFF;
	AUTO_INCREMENT_CONFIG_DEVICE_JTAG_USER_CODE = ON;
	EPROM_USE_CHECKSUM_AS_USERCODE = OFF;
	FLEX10K_CONFIG_DEVICE_JTAG_USER_CODE = FFFFFFFF;
	MERCURY_CONFIG_DEVICE_JTAG_USER_CODE = FFFFFFFF;
	APEX20K_CONFIG_DEVICE_JTAG_USER_CODE = FFFFFFFF;
	STRATIX_CONFIG_DEVICE_JTAG_USER_CODE = FFFFFFFF;
	STRATIX_CONFIGURATION_DEVICE = EPC2;
	FLEX10K_CONFIGURATION_DEVICE = EPC2;
	FLEX6K_CONFIGURATION_DEVICE = EPC1;
	MERCURY_CONFIGURATION_DEVICE = EPC2;
	EXCALIBUR_CONFIGURATION_DEVICE = EPC2;
	APEX20K_CONFIGURATION_DEVICE = EPC2;
	USE_CONFIGURATION_DEVICE = ON;
	ENABLE_INIT_DONE_OUTPUT = OFF;
	FLEX10K_ENABLE_LOCK_OUTPUT = OFF;
	ENABLE_DEVICE_WIDE_OE = OFF;
	ENABLE_DEVICE_WIDE_RESET = OFF;
	RELEASE_CLEARS_BEFORE_TRI_STATES = OFF;
	AUTO_RESTART_CONFIGURATION = OFF;
	ENABLE_VREFB_PIN = OFF;
	ENABLE_VREFA_PIN = OFF;
	SECURITY_BIT = OFF;
	USER_START_UP_CLOCK = OFF;
	APEX_II_CONFIGURATION_SCHEME = "PASSIVE SERIAL";
	FLEX10K_CONFIGURATION_SCHEME = "PASSIVE SERIAL";
	FLEX6K_CONFIGURATION_SCHEME = "PASSIVE SERIAL";
	MERCURY_CONFIGURATION_SCHEME = "PASSIVE SERIAL";
	EXCALIBUR_CONFIGURATION_SCHEME = "PASSIVE SERIAL";
	STRATIX_CONFIGURATION_SCHEME = "PASSIVE SERIAL";
	APEX20K_CONFIGURATION_SCHEME = "PASSIVE SERIAL";
	STRATIX_UPDATE_MODE = STANDARD;
	USE_CHECKSUM_AS_USERCODE = OFF;
	MAX7000_JTAG_USER_CODE = FFFFFFFF;
	FLEX10K_JTAG_USER_CODE = 7F;
	MERCURY_JTAG_USER_CODE = FFFFFFFF;
	APEX20K_JTAG_USER_CODE = FFFFFFFF;
	STRATIX_JTAG_USER_CODE = FFFFFFFF;
	RESERVE_NCEO_AFTER_CONFIGURATION = OFF;
	FLEX10K_ENABLE_LOW_VOLTAGE_MODE_ON_CONFIG_DEVICE = ON;
	FLEX6K_ENABLE_LOW_VOLTAGE_MODE_ON_CONFIG_DEVICE = OFF;
	MAX7000_ENABLE_JTAG_BST_SUPPORT = ON;
	ENABLE_JTAG_BST_SUPPORT = OFF;
	MAX7000_USE_CHECKSUM_AS_USERCODE = OFF;
}