📄 dds1.mrp
字号:
Release 6.1i Map G.23Xilinx Mapping Report File for Design 'DDS1'Design Information------------------Command Line : D:/Xilinx/bin/nt/map.exe -intstyle ise -p xc3s400-pq208-4 -cm
area -pr b -k 4 -c 100 -tx off -o DDS1_map.ncd DDS1.ngd DDS1.pcf Target Device : x3s400Target Package : pq208Target Speed : -4Mapper Version : spartan3 -- $Revision: 1.16 $Mapped Date : Thu Aug 16 15:36:58 2007Design Summary--------------Number of errors: 0Number of warnings: 0Logic Utilization: Number of Slice Flip Flops: 28 out of 7,168 1% Number of 4 input LUTs: 33 out of 7,168 1%Logic Distribution: Number of occupied Slices: 19 out of 3,584 1% Number of Slices containing only related logic: 19 out of 19 100% Number of Slices containing unrelated logic: 0 out of 19 0% *See NOTES below for an explanation of the effects of unrelated logicTotal Number 4 input LUTs: 35 out of 7,168 1% Number used as logic: 33 Number used as a route-thru: 2 Number of bonded IOBs: 47 out of 141 33% IOB Flip Flops: 32 Number of Block RAMs: 1 out of 16 6% Number of MULT18X18s: 1 out of 16 6% Number of GCLKs: 1 out of 8 12%Total equivalent gate count for design: 70,385Additional JTAG gate count for IOBs: 2,256Peak Memory Usage: 74 MBNOTES: Related logic is defined as being logic that shares connectivity - e.g. two LUTs are "related" if they share common inputs. When assembling slices, Map gives priority to combine logic that is related. Doing so results in the best timing performance. Unrelated logic shares no connectivity. Map will only begin packing unrelated logic into a slice once 99% of the slices are occupied through related logic packing. Note that once logic distribution reaches the 99% level through related logic packing, this does not mean the device is completely utilized. Unrelated logic packing will then begin, continuing until all usable LUTs and FFs are occupied. Depending on your timing budget, increased levels of unrelated logic packing may adversely affect the overall timing performance of your design.Table of Contents-----------------Section 1 - ErrorsSection 2 - WarningsSection 3 - InformationalSection 4 - Removed Logic SummarySection 5 - Removed LogicSection 6 - IOB PropertiesSection 7 - RPMsSection 8 - Guide ReportSection 9 - Area Group SummarySection 10 - Modular Design SummarySection 11 - Timing ReportSection 1 - Errors------------------Section 2 - Warnings--------------------Section 3 - Informational-------------------------INFO:LIT:95 - All of the external outputs in this design are using slew rate
limited output drivers. The delay on speed critical outputs can be
dramatically reduced by designating them as fast outputs in the schematic.INFO:MapLib:562 - No environment variables are currently set.INFO:MapLib:535 - The following Virtex BUFG(s) is/are being retargetted to
Virtex2 BUFGMUX(s) with input tied to I0 and Select pin tied to constant 0: BUFGP symbol "CLK_BUFGP" (output signal=CLK_BUFGP)Section 4 - Removed Logic Summary--------------------------------- 1 block(s) removed 3 block(s) optimized awaySection 5 - Removed Logic-------------------------Unused block "rom/VCC" (ONE) removed.Optimized Block(s):TYPE BLOCKGND XST_GNDVCC XST_VCCGND rom/GNDTo enable printing of redundant blocks removed and signals merged, set the
detailed map report option and rerun map.Section 6 - IOB Properties--------------------------+------------------------------------------------------------------------------------------------------------------------+| IOB Name | Type | Direction | IO Standard | Drive | Slew | Reg (s) | Resistor | IOB || | | | | Strength | Rate | | | Delay |+------------------------------------------------------------------------------------------------------------------------+| CLK | IOB | INPUT | LVCMOS25 | | | | | || DATA_FRE<0> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_FRE<1> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_FRE<2> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_FRE<3> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_FRE<4> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_FRE<5> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_FRE<6> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_FRE<7> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_FRE<8> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_FRE<9> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_FRE<10> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_FRE<11> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_FRE<12> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_FRE<13> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_FRE<14> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_FRE<15> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_PHA<0> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_PHA<1> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_PHA<2> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_PHA<3> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_PHA<4> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_PHA<5> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_PHA<6> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_PHA<7> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_PHA<8> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_PHA<9> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_PHA<10> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_PHA<11> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_PHA<12> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_PHA<13> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_PHA<14> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || DATA_PHA<15> | IOB | INPUT | LVCMOS25 | | | INFF1 | | IFD || SCLR | IOB | INPUT | LVCMOS25 | | | | | || SINE<0> | IOB | OUTPUT | LVCMOS25 | 12 | SLOW | | | || SINE<1> | IOB | OUTPUT | LVCMOS25 | 12 | SLOW | | | || SINE<2> | IOB | OUTPUT | LVCMOS25 | 12 | SLOW | | | || SINE<3> | IOB | OUTPUT | LVCMOS25 | 12 | SLOW | | | || SINE<4> | IOB | OUTPUT | LVCMOS25 | 12 | SLOW | | | || SINE<5> | IOB | OUTPUT | LVCMOS25 | 12 | SLOW | | | || SINE<6> | IOB | OUTPUT | LVCMOS25 | 12 | SLOW | | | || SINE<7> | IOB | OUTPUT | LVCMOS25 | 12 | SLOW | | | || SINE<8> | IOB | OUTPUT | LVCMOS25 | 12 | SLOW | | | || SINE<9> | IOB | OUTPUT | LVCMOS25 | 12 | SLOW | | | || SINE<10> | IOB | OUTPUT | LVCMOS25 | 12 | SLOW | | | || WE | IOB | INPUT | LVCMOS25 | | | | | || rst | IOB | INPUT | LVCMOS25 | | | | | |+------------------------------------------------------------------------------------------------------------------------+Section 7 - RPMs----------------Section 8 - Guide Report------------------------Guide not run on this design.Section 9 - Area Group Summary------------------------------No area groups were found in this design.Section 10 - Modular Design Summary-----------------------------------Modular Design not used for this design.Section 11 - Timing Report--------------------------This design was not run using timing mode.⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -