📄 netevent.h
字号:
//
// MessageText:
//
// %2 : A Token Ring Lobe Wire Fault has occurred. Verify cable
// connections. The adapter will continue to try to reinsert back
// into the ring.
//
#define EVENT_NDIS_LOBE_FAILUE_ERROR 0x800013A3L
//
// MessageId: EVENT_NDIS_SIGNAL_LOSS_ERROR
//
// MessageText:
//
// %2 : The adapter had detected a loss of signal on the ring. The adapter
// will continue to try to reinsert back into the ring.
//
#define EVENT_NDIS_SIGNAL_LOSS_ERROR 0x800013A4L
//
// MessageId: EVENT_NDIS_REMOVE_RECEIVED_ERROR
//
// MessageText:
//
// %2 : The adapter has received a request to deinsert from the
// ring. The adapter will continue to try to reinsert back into the ring.
//
#define EVENT_NDIS_REMOVE_RECEIVED_ERROR 0x800013A5L
//
// MessageId: EVENT_NDIS_TOKEN_RING_CORRECTION
//
// MessageText:
//
// %2 : The adapter has successfully reinserted back into the ring.
//
#define EVENT_NDIS_TOKEN_RING_CORRECTION 0x400013A6L
//
// MessageId: EVENT_NDIS_ADAPTER_CHECK_ERROR
//
// MessageText:
//
// %2 : The adapter has detected an Adapter Check as a result of some
// unrecoverable hardware of software error. Please contact your service provider.
//
#define EVENT_NDIS_ADAPTER_CHECK_ERROR 0xC00013A7L
//
// MessageId: EVENT_NDIS_RESET_FAILURE_ERROR
//
// MessageText:
//
// %2 : The adapter failed to reset within a specified time. The adapter will
// continue to try to reset. This could be the result of a hardware failure.
//
#define EVENT_NDIS_RESET_FAILURE_ERROR 0x800013A8L
//
// MessageId: EVENT_NDIS_CABLE_DISCONNECTED_ERROR
//
// MessageText:
//
// %2 : The adapter has detected that the Token Ring cable is disconnected from
// the adapter. Please reconnect the Token Ring cable. The adapter will continue
// to try to reset until the connection is repaired.
//
#define EVENT_NDIS_CABLE_DISCONNECTED_ERROR 0x800013A9L
//
// MessageId: EVENT_NDIS_RESET_FAILURE_CORRECTION
//
// MessageText:
//
// %2 : The adapter has successfully completed a previously failed reset.
//
#define EVENT_NDIS_RESET_FAILURE_CORRECTION 0x800013AAL
/////////////////////////////////////////////////////////////////////////
//
// General NT System Events
//
/////////////////////////////////////////////////////////////////////////
//
// Eventlog Events 6000 - 6099
//
//
// MessageId: EVENT_LOG_FULL
//
// MessageText:
//
// The %1 log file is full.
//
#define EVENT_LOG_FULL 0x80001770L
//
// MessageId: EVENT_LogFileNotOpened
//
// MessageText:
//
// The %1 log file cannot be opened.
//
#define EVENT_LogFileNotOpened 0x80001771L
//
// MessageId: EVENT_LogFileCorrupt
//
// MessageText:
//
// The %1 log file is corrupted and will be cleared.
//
#define EVENT_LogFileCorrupt 0x80001772L
//
// MessageId: EVENT_DefaultLogCorrupt
//
// MessageText:
//
// The Application log file could not be opened. %1 will be used as the default
// log file.
//
#define EVENT_DefaultLogCorrupt 0x80001773L
//
// MessageId: EVENT_BadDriverPacket
//
// MessageText:
//
// A driver packet received from the I/O subsystem was invalid. The data is the
// packet.
//
#define EVENT_BadDriverPacket 0x80001774L
//
// MessageId: EVENT_EventlogStarted
//
// MessageText:
//
// The Event log service was started.
//
#define EVENT_EventlogStarted 0x80001775L
//
// MessageId: EVENT_EventlogStopped
//
// MessageText:
//
// The Event log service was stopped.
//
#define EVENT_EventlogStopped 0x80001776L
//
// MessageId: TITLE_EventlogMessageBox
//
// MessageText:
//
// Eventlog Service %0
//
#define TITLE_EventlogMessageBox 0x80001777L
//
// MessageId: EVENT_EventlogAbnormalShutdown
//
// MessageText:
//
// The previous system shutdown at %1 on %2 was unexpected.
//
#define EVENT_EventlogAbnormalShutdown 0x80001778L
//
// MessageId: EVENT_EventLogProductInfo
//
// MessageText:
//
// Microsoft (R) Windows 2000 (R) %1 %2 %3 %4.
//
#define EVENT_EventLogProductInfo 0x80001779L
//
// MessageId: EVENT_ServiceNoEventLog
//
// MessageText:
//
// The %1 service was unable to set up an event source.
//
#define EVENT_ServiceNoEventLog 0xC000177AL
//
// System Events 6100 - 6199
//
//
// MessageId: EVENT_UP_DRIVER_ON_MP
//
// MessageText:
//
// A uniprocessor-specific driver was loaded on a multiprocessor system. The driver could not load.
//
#define EVENT_UP_DRIVER_ON_MP 0xC00017D4L
//
// Service Controller Events 7000 - 7899
//
//
// MessageId: EVENT_SERVICE_START_FAILED
//
// MessageText:
//
// The %1 service failed to start due to the following error: %n%2
//
#define EVENT_SERVICE_START_FAILED 0xC0001B58L
//
// MessageId: EVENT_SERVICE_START_FAILED_II
//
// MessageText:
//
// The %1 service depends on the %2 service which failed to start because of the following error: %n%3
//
#define EVENT_SERVICE_START_FAILED_II 0xC0001B59L
//
// MessageId: EVENT_SERVICE_START_FAILED_GROUP
//
// MessageText:
//
// The %1 service depends on the %2 group and no member of this group started.
//
#define EVENT_SERVICE_START_FAILED_GROUP 0xC0001B5AL
//
// MessageId: EVENT_SERVICE_START_FAILED_NONE
//
// MessageText:
//
// The %1 service depends on the following nonexistent service: %2
//
#define EVENT_SERVICE_START_FAILED_NONE 0xC0001B5BL
//
// MessageId: EVENT_CALL_TO_FUNCTION_FAILED
//
// MessageText:
//
// The %1 call failed with the following error: %n%2
//
#define EVENT_CALL_TO_FUNCTION_FAILED 0xC0001B5DL
//
// MessageId: EVENT_CALL_TO_FUNCTION_FAILED_II
//
// MessageText:
//
// The %1 call failed for %2 with the following error: %n%3
//
#define EVENT_CALL_TO_FUNCTION_FAILED_II 0xC0001B5EL
//
// MessageId: EVENT_REVERTED_TO_LASTKNOWNGOOD
//
// MessageText:
//
// The system reverted to its last known good configuration. The system is restarting....
//
#define EVENT_REVERTED_TO_LASTKNOWNGOOD 0xC0001B5FL
//
// MessageId: EVENT_BAD_ACCOUNT_NAME
//
// MessageText:
//
// No backslash is in the account name.
//
#define EVENT_BAD_ACCOUNT_NAME 0xC0001B60L
//
// MessageId: EVENT_CONNECTION_TIMEOUT
//
// MessageText:
//
// Timeout (%1 milliseconds) waiting for the %2 service to connect.
//
#define EVENT_CONNECTION_TIMEOUT 0xC0001B61L
//
// MessageId: EVENT_READFILE_TIMEOUT
//
// MessageText:
//
// Timeout (%1 milliseconds) waiting for ReadFile.
//
#define EVENT_READFILE_TIMEOUT 0xC0001B62L
//
// MessageId: EVENT_TRANSACT_TIMEOUT
//
// MessageText:
//
// Timeout (%1 milliseconds) waiting for a transaction response from the %2 service.
//
#define EVENT_TRANSACT_TIMEOUT 0xC0001B63L
//
// MessageId: EVENT_TRANSACT_INVALID
//
// MessageText:
//
// Message returned in transaction has incorrect size.
//
#define EVENT_TRANSACT_INVALID 0xC0001B64L
//
// MessageId: EVENT_FIRST_LOGON_FAILED
//
// MessageText:
//
// Logon attempt with current password failed with the following error: %n%1
//
#define EVENT_FIRST_LOGON_FAILED 0xC0001B65L
//
// MessageId: EVENT_SECOND_LOGON_FAILED
//
// MessageText:
//
// Second logon attempt with old password also failed with the following error: %n%1
//
#define EVENT_SECOND_LOGON_FAILED 0xC0001B66L
//
// MessageId: EVENT_INVALID_DRIVER_DEPENDENCY
//
// MessageText:
//
// Boot-start or system-start driver (%1) must not depend on a service.
//
#define EVENT_INVALID_DRIVER_DEPENDENCY 0xC0001B67L
//
// MessageId: EVENT_BAD_SERVICE_STATE
//
// MessageText:
//
// The %1 service has reported an invalid current state %2.
//
#define EVENT_BAD_SERVICE_STATE 0xC0001B68L
//
// MessageId: EVENT_CIRCULAR_DEPENDENCY_DEMAND
//
// MessageText:
//
// Detected circular dependencies demand starting %1.
//
#define EVENT_CIRCULAR_DEPENDENCY_DEMAND 0xC0001B69L
//
// MessageId: EVENT_CIRCULAR_DEPENDENCY_AUTO
//
// MessageText:
//
// Detected circular dependencies auto-starting services.
//
#define EVENT_CIRCULAR_DEPENDENCY_AUTO 0xC0001B6AL
//
// MessageId: EVENT_DEPEND_ON_LATER_SERVICE
//
// MessageText:
//
// Circular dependency: The %1 service depends on a service in a group which starts later.
//
#define EVENT_DEPEND_ON_LATER_SERVICE 0xC0001B6BL
//
// MessageId: EVENT_DEPEND_ON_LATER_GROUP
//
// MessageText:
//
// Circular dependency: The %1 service depends on a group which starts later.
//
#define EVENT_DEPEND_ON_LATER_GROUP 0xC0001B6CL
//
// MessageId: EVENT_SEVERE_SERVICE_FAILED
//
// MessageText:
//
// About to revert to the last known good configuration because the %1 service failed to start.
//
#define EVENT_SEVERE_SERVICE_FAILED 0xC0001B6DL
//
// MessageId: EVENT_SERVICE_START_HUNG
//
// MessageText:
//
// The %1 service hung on starting.
//
#define EVENT_SERVICE_START_HUNG 0xC0001B6EL
//
// MessageId: EVENT_SERVICE_EXIT_FAILED
//
// MessageText:
//
// The %1 service terminated with the following error: %n%2
//
#define EVENT_SERVICE_EXIT_FAILED 0xC0001B6FL
//
// MessageId: EVENT_SERVICE_EXIT_FAILED_SPECIFIC
//
// MessageText:
//
// The %1 service terminated with service-specific error %2.
//
#define EVENT_SERVICE_EXIT_FAILED_SPECIFIC 0xC0001B70L
//
// MessageId: EVENT_SERVICE_START_AT_BOOT_FAILED
//
// MessageText:
//
// At least one service or driver failed during system startup. Use Event Viewer to examine the event log for details.
//
#define EVENT_SERVICE_START_AT_BOOT_FAILED 0xC0001B71L
//
// MessageId: EVENT_BOOT_SYSTEM_DRIVERS_FAILED
//
// MessageText:
//
// The following boot-start or system-start driver(s) failed to load: %1
//
#define EVENT_BOOT_SYSTEM_DRIVERS_FAILED 0xC0001B72L
//
// MessageId: EVENT_RUNNING_LASTKNOWNGOOD
//
// MessageText:
//
// Windows 2000 could not be started as configured. A previous working configuration was used instead.
//
#define EVENT_RUNNING_LASTKNOWNGOOD 0xC0001B73L
//
// MessageId: EVENT_TAKE_OWNERSHIP
//
// MessageText:
//
// The %1 Registry key denied access to SYSTEM account programs so the Service Control Manager took ownership of the Registry key.
//
#define EVENT_TAKE_OWNERSHIP 0xC0001B74L
//
// This Text is used as a title for the message box used to display
// MessageId 7027. It is not an event or error message.
//
//
// MessageId: TITLE_SC_MESSAGE_BOX
//
// MessageText:
//
// Service Control Manager %0
//
#define TITLE_SC_MESSAGE_BOX 0xC0001B75L
//
// MessageId: EVENT_SERVICE_NOT_INTERACTIVE
//
// MessageText:
//
// The %1 service is marked as an interactive service. However, the system is configured to not allow interactive services. This service may not function properly.
//
#define EVENT_SERVICE_NOT_INTERACTIVE 0xC0001B76L
//
// Parameter %4 is the value, in decimal, of the SC_ACTION_ constant for
// the action described in parameter %5.
//
//
// MessageId: EVENT_SERVICE_CRASH
//
// MessageText:
//
// The %1 service terminated unexpectedly. It has done this %2 time(s). The following corrective action will be taken in %3 milliseconds: %5.
//
#define EVENT_SERVICE_CRASH 0xC0001B77L
//
// Parameter %1 is the value, in decimal, of the SC_ACTION_ constant for
// the action described in parameter %2.
//
//
// MessageId: EVENT_SERVICE_RECOVERY_FAILED
//
// MessageText:
//
// The Service Control Manager tried to take a corrective action (%2) after the unexpected termination of the %3 service, but this action failed with the following error: %n%4
//
#define EVENT_SERVICE_RECOVERY_FAILED 0xC0001B78L
//
// MessageId: EVENT_SERVICE_SCESRV_FAILED
//
// MessageText:
//
// The Service Control Manager is not initialized successfully therefore the
// system is shutting down. Security configuration server (scesrv.dll) failed
// to initialize with error %1
//
#define EVENT_SERVICE_SCESRV_FAILED 0xC0001B79L
//
// Schedule (AT command) Service Events 7900 - 7999
//
//
// MessageId: EVENT_COMMAND_NOT_INTERACTIVE
//
// MessageText:
//
// The %1 command is marked as an interactive command. However, the system is
// configured to not allow interactive command execution. This command may not
// function properly.
//
#define EVENT_COMMAND_NOT_INTERACTIVE 0xC0001EDCL
//
// MessageId: EVENT_COMMAND_START_FAILED
//
// MessageText:
//
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -