📄 guangshanchi.pin
字号:
-- Copyright (C) 1991-2005 Altera Corporation
-- Your use of Altera Corporation's design tools, logic functions
-- and other software and tools, and its AMPP partner logic
-- functions, and any output files any of the foregoing
-- (including device programming or simulation files), and any
-- associated documentation or information are expressly subject
-- to the terms and conditions of the Altera Program License
-- Subscription Agreement, Altera MegaCore Function License
-- Agreement, or other applicable license agreement, including,
-- without limitation, that your use is for the sole purpose of
-- programming logic devices manufactured by Altera and sold by
-- Altera or its authorized distributors. Please refer to the
-- applicable agreement for further details.
--
-- This is a Quartus II output file. It is for reporting purposes only, and is
-- not intended for use as a Quartus II input file. This file cannot be used
-- to make Quartus II pin assignments - for instructions on how to make pin
-- assignments, please see Quartus II help.
---------------------------------------------------------------------------------
---------------------------------------------------------------------------------
-- NC : No Connect. This pin has no internal connection to the device.
-- VCC : Dedicated power pin, which MUST be connected to VCC.
-- VCCIO : Dedicated power pin, which MUST be connected to VCC
-- of its bank.
-- GND : Dedicated ground pin. Dedicated GND pins MUST be connected to GND.
-- It can also be used to report unused dedicated pins. The connection
-- on the board for unused dedicated pins depends on whether this will
-- be used in a future design. One example is device migration. When
-- using device migration, refer to the device pin-tables. If it is a
-- GND pin in the pin table or if it will not be used in a future design
-- for another purpose the it MUST be connected to GND. If it is an unused
-- dedicated pin, then it can be connected to a valid signal on the board
-- (low, high, or toggling) if that signal is required for a different
-- revision of the design.
-- GND+ : Unused input pin. It can also be used to report unused dual-purpose pins.
-- This pin should be connected to GND. It may also be connected to a
-- valid signal on the board (low, high, or toggling) if that signal
-- is required for a different revision of the design.
-- GND* : Unused I/O pin. This pin can either be left unconnected or
-- connected to GND. Connecting this pin to GND will improve the
-- device's immunity to noise.
-- RESERVED : Unused I/O pin, which MUST be left unconnected.
-- RESERVED_INPUT : Pin is tri-stated and should be connected to the board.
-- NON_MIGRATABLE: This pin cannot be migrated.
---------------------------------------------------------------------------------
Quartus II Version 5.0 Build 148 04/26/2005 SJ Full Version
CHIP "GuangShanChi" ASSIGNED TO AN: EPM7128STC100-10
Pin Name/Usage : Location : Dir. : I/O Standard : Voltage : I/O Bank : User Assignment
-------------------------------------------------------------------------------------------------------------
Cnt8b[2] : 1 : output : TTL : : : N
Cnt8b[3] : 2 : output : TTL : : : N
VCCIO : 3 : power : : 5.0V : :
TDI : 4 : input : TTL : : : N
cnt[1] : 5 : output : TTL : : : N
cnt[2] : 6 : output : TTL : : : N
cnt[3] : 7 : output : TTL : : : N
cnt[4] : 8 : output : TTL : : : N
cnt[5] : 9 : output : TTL : : : N
cnt[6] : 10 : output : TTL : : : N
GND : 11 : gnd : : : :
cnt[7] : 12 : output : TTL : : : N
cnt[9] : 13 : output : TTL : : : N
cnt[8] : 14 : output : TTL : : : N
TMS : 15 : input : TTL : : : N
cnt[15] : 16 : output : TTL : : : N
Cnt8b[0] : 17 : output : TTL : : : N
VCCIO : 18 : power : : 5.0V : :
cnt[17] : 19 : output : TTL : : : N
cnt[11] : 20 : output : TTL : : : N
cnt[12] : 21 : output : TTL : : : N
cnt[13] : 22 : output : TTL : : : N
cnt[14] : 23 : output : TTL : : : N
cnt[16] : 24 : output : TTL : : : N
cnt[0] : 25 : output : TTL : : : N
GND : 26 : gnd : : : :
B : 27 : input : TTL : : : N
RESERVED : 28 : : : : :
OutSel[0] : 29 : input : TTL : : : N
cnt[23] : 30 : output : TTL : : : N
cnt[22] : 31 : output : TTL : : : N
cnt[21] : 32 : output : TTL : : : N
cnt[20] : 33 : output : TTL : : : N
VCCIO : 34 : power : : 5.0V : :
cnt[18] : 35 : output : TTL : : : N
cnt[19] : 36 : output : TTL : : : N
cnt[10] : 37 : output : TTL : : : N
GND : 38 : gnd : : : :
VCCINT : 39 : power : : 5.0V : :
RESERVED : 40 : : : : :
RESERVED : 41 : : : : :
RESERVED : 42 : : : : :
GND : 43 : gnd : : : :
RESERVED : 44 : : : : :
RESERVED : 45 : : : : :
RESERVED : 46 : : : : :
RESERVED : 47 : : : : :
RESERVED : 48 : : : : :
RESERVED : 49 : : : : :
RESERVED : 50 : : : : :
VCCIO : 51 : power : : 5.0V : :
RESERVED : 52 : : : : :
RESERVED : 53 : : : : :
RESERVED : 54 : : : : :
RESERVED : 55 : : : : :
OutSel[1] : 56 : input : TTL : : : N
RESERVED : 57 : : : : :
RESERVED : 58 : : : : :
GND : 59 : gnd : : : :
RESERVED : 60 : : : : :
RESERVED : 61 : : : : :
TCK : 62 : input : TTL : : : N
RESERVED : 63 : : : : :
RESERVED : 64 : : : : :
RESERVED : 65 : : : : :
VCCIO : 66 : power : : 5.0V : :
RESERVED : 67 : : : : :
RESERVED : 68 : : : : :
RESERVED : 69 : : : : :
RESERVED : 70 : : : : :
RESERVED : 71 : : : : :
RESERVED : 72 : : : : :
TDO : 73 : output : TTL : : : N
GND : 74 : gnd : : : :
RESERVED : 75 : : : : :
RESERVED : 76 : : : : :
RESERVED : 77 : : : : :
RESERVED : 78 : : : : :
RESERVED : 79 : : : : :
RESERVED : 80 : : : : :
RESERVED : 81 : : : : :
VCCIO : 82 : power : : 5.0V : :
RESERVED : 83 : : : : :
RESERVED : 84 : : : : :
A : 85 : input : TTL : : : N
GND : 86 : gnd : : : :
CLK : 87 : input : TTL : : : N
GND+ : 88 : : : : :
GND+ : 89 : : : : :
GND+ : 90 : : : : :
VCCINT : 91 : power : : 5.0V : :
SCLR : 92 : input : TTL : : : N
RESERVED : 93 : : : : :
RESERVED : 94 : : : : :
GND : 95 : gnd : : : :
Cnt8b[7] : 96 : output : TTL : : : N
Cnt8b[6] : 97 : output : TTL : : : N
Cnt8b[5] : 98 : output : TTL : : : N
Cnt8b[4] : 99 : output : TTL : : : N
Cnt8b[1] : 100 : output : TTL : : : N
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -