eth_wishbone.v

这是一个很好的Verilog 编写的8位RISC CPU源码（可做为MCU）

end

assign ReadTxDataFromFifo_wb = ReadTxDataFromFifo_sync2 & ~ReadTxDataFromFifo_sync3;
// End: Generation of the ReadTxDataFromFifo_tck signal and synchronization to the WB_CLK_I
*/

// Start: Generation of the ReadTxDataFromFifo_tck signal and synchronization to the WB_CLK_I
reg ReadTxDataFromFifo_sync1;
reg ReadTxDataFromFifo_sync2;
reg ReadTxDataFromFifo_sync3;
reg ReadTxDataFromFifo_syncb1;
reg ReadTxDataFromFifo_syncb2;
reg ReadTxDataFromFifo_syncb3;


always @ (posedge MTxClk or posedge Reset)
begin
  if(Reset)
    ReadTxDataFromFifo_tck <=#Tp 1'b0;
  else
  if(TxStartFrm_sync2 & ~TxStartFrm | TxUsedData & Flop & TxByteCnt == 2'h3 & ~LastWord | TxStartFrm & TxUsedData & Flop & TxByteCnt == 2'h0)
     ReadTxDataFromFifo_tck <=#Tp 1'b1;
  else
  if(ReadTxDataFromFifo_syncb2 & ~ReadTxDataFromFifo_syncb3)
    ReadTxDataFromFifo_tck <=#Tp 1'b0;
end

// Synchronizing TxStartFrm_wb to MTxClk
always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    ReadTxDataFromFifo_sync1 <=#Tp 1'b0;
  else
    ReadTxDataFromFifo_sync1 <=#Tp ReadTxDataFromFifo_tck;
end

always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    ReadTxDataFromFifo_sync2 <=#Tp 1'b0;
  else
    ReadTxDataFromFifo_sync2 <=#Tp ReadTxDataFromFifo_sync1;
end

always @ (posedge MTxClk or posedge Reset)
begin
  if(Reset)
    ReadTxDataFromFifo_syncb1 <=#Tp 1'b0;
  else
    ReadTxDataFromFifo_syncb1 <=#Tp ReadTxDataFromFifo_sync2;
end

always @ (posedge MTxClk or posedge Reset)
begin
  if(Reset)
    ReadTxDataFromFifo_syncb2 <=#Tp 1'b0;
  else
    ReadTxDataFromFifo_syncb2 <=#Tp ReadTxDataFromFifo_syncb1;
end

always @ (posedge MTxClk or posedge Reset)
begin
  if(Reset)
    ReadTxDataFromFifo_syncb3 <=#Tp 1'b0;
  else
    ReadTxDataFromFifo_syncb3 <=#Tp ReadTxDataFromFifo_syncb2;
end

always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    ReadTxDataFromFifo_sync3 <=#Tp 1'b0;
  else
    ReadTxDataFromFifo_sync3 <=#Tp ReadTxDataFromFifo_sync2;
end

assign ReadTxDataFromFifo_wb = ReadTxDataFromFifo_sync2 & ~ReadTxDataFromFifo_sync3;
// End: Generation of the ReadTxDataFromFifo_tck signal and synchronization to the WB_CLK_I


// Synchronizing TxRetry signal (synchronized to WISHBONE clock)
always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    TxRetrySync1 <=#Tp 1'b0;
  else
    TxRetrySync1 <=#Tp TxRetry;
end

always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    TxRetry_wb <=#Tp 1'b0;
  else
    TxRetry_wb <=#Tp TxRetrySync1;
end


// Synchronized TxDone_wb signal (synchronized to WISHBONE clock)
always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    TxDoneSync1 <=#Tp 1'b0;
  else
    TxDoneSync1 <=#Tp TxDone;
end

always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    TxDone_wb <=#Tp 1'b0;
  else
    TxDone_wb <=#Tp TxDoneSync1;
end

// Synchronizing TxAbort signal (synchronized to WISHBONE clock)
always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    TxAbortSync1 <=#Tp 1'b0;
  else
    TxAbortSync1 <=#Tp TxAbort;
end

always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    TxAbort_wb <=#Tp 1'b0;
  else
    TxAbort_wb <=#Tp TxAbortSync1;
end


reg RxAbortSync1;
reg RxAbortSync2;
reg RxAbortSync3;
reg RxAbortSync4;
reg RxAbortSyncb1;
reg RxAbortSyncb2;

//assign StartRxBDRead = RxStatusWrite | RxAbortLatched;
assign StartRxBDRead = RxStatusWrite | RxAbortSync3 & ~RxAbortSync4;

// Reading the Rx buffer descriptor
always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    RxBDRead <=#Tp 1'b1;
  else
  if(StartRxBDRead & ~RxBDReady)
    RxBDRead <=#Tp 1'b1;
  else
  if(RxBDReady)
    RxBDRead <=#Tp 1'b0;
end


// Reading of the next receive buffer descriptor starts after reception status is
// written to the previous one.

// Latching READY status of the Rx buffer descriptor
always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    RxBDReady <=#Tp 1'b0;
  else
  if(ShiftEnded | RxAbortSync2 & ~RxAbortSync3)
    RxBDReady <=#Tp 1'b0;
  else
  if(RxEn & RxEn_q & RxBDRead)
    RxBDReady <=#Tp ram_do[15]; // RxBDReady is sampled only once at the beginning
end

// Latching Rx buffer descriptor status
// Data is avaliable one cycle after the access is started (at that time signal RxEn is not active)
always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    RxStatus <=#Tp 2'h0;
  else
  if(RxEn & RxEn_q & RxBDRead)
    RxStatus <=#Tp ram_do[14:13];
end




// Reading Rx BD pointer


assign StartRxPointerRead = RxBDRead & RxBDReady;

// Reading Tx BD Pointer
always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    RxPointerRead <=#Tp 1'b0;
  else
  if(StartRxPointerRead)
    RxPointerRead <=#Tp 1'b1;
  else
  if(RxEn_q)
    RxPointerRead <=#Tp 1'b0;
end


//Latching Rx buffer pointer from buffer descriptor;
always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    RxPointer <=#Tp 32'h0;
  else
  if(RxEn & RxEn_q & RxPointerRead)
    RxPointer <=#Tp {ram_do[31:2], 2'h0};
  else
  if(MasterWbRX & m_wb_ack_i)
      RxPointer <=#Tp RxPointer + 3'h4; // Word access  (always word access. m_wb_sel_o are used for selecting bytes)
end


//Latching last addresses from buffer descriptor (used as byte-half-word indicator);
always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    RxPointerLatched[1:0] <=#Tp 0;
  else
  if(MasterWbRX & m_wb_ack_i)                 // After first write all m_wb_sel_tmp_rx are active
    RxPointerLatched[1:0] <=#Tp 0;
  else
  if(RxEn & RxEn_q & RxPointerRead)
    RxPointerLatched[1:0] <=#Tp ram_do[1:0];
end


always @ (RxPointerLatched)
begin
  case(RxPointerLatched[1:0])  // synopsys parallel_case
    2'h0 : m_wb_sel_tmp_rx[3:0] = 4'hf;
    2'h1 : m_wb_sel_tmp_rx[3:0] = 4'h7;
    2'h2 : m_wb_sel_tmp_rx[3:0] = 4'h3;
    2'h3 : m_wb_sel_tmp_rx[3:0] = 4'h1;
  endcase
end


always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    RxEn_needed <=#Tp 1'b0;
  else
  if(~RxBDReady & r_RxEn & WbEn & ~WbEn_q)
    RxEn_needed <=#Tp 1'b1;
  else
  if(RxPointerRead & RxEn & RxEn_q)
    RxEn_needed <=#Tp 1'b0;
end


// Reception status is written back to the buffer descriptor after the end of frame is detected.
assign RxStatusWrite = ShiftEnded & RxEn & RxEn_q;

reg RxStatusWriteLatched;
reg RxStatusWrite_rck;

always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    RxStatusWriteLatched <=#Tp 1'b0;
  else
  if(RxStatusWrite & ~RxStatusWrite_rck)
    RxStatusWriteLatched <=#Tp 1'b1;
  else
  if(RxStatusWrite_rck)
    RxStatusWriteLatched <=#Tp 1'b0;
end


always @ (posedge MRxClk or posedge Reset)
begin
  if(Reset)
    RxStatusWrite_rck <=#Tp 1'b0;
  else
  if(RxStatusWriteLatched)
    RxStatusWrite_rck <=#Tp 1'b1;
  else
    RxStatusWrite_rck <=#Tp 1'b0;
end


reg RxEnableWindow;

// Indicating that last byte is being reveived
always @ (posedge MRxClk or posedge Reset)
begin
  if(Reset)
    LastByteIn <=#Tp 1'b0;
  else
  if(ShiftWillEnd & (&RxByteCnt) | RxAbort)
    LastByteIn <=#Tp 1'b0;
  else
  if(RxValid & RxBDReady & RxEndFrm & ~(&RxByteCnt) & RxEnableWindow)
    LastByteIn <=#Tp 1'b1;
end

reg ShiftEnded_tck;
reg ShiftEndedSync1;
reg ShiftEndedSync2;
reg ShiftEndedSync3;
reg ShiftEndedSync_c1;
reg ShiftEndedSync_c2;

wire StartShiftWillEnd;
//assign StartShiftWillEnd = LastByteIn & (&RxByteCnt) | RxValid & RxEndFrm & (&RxByteCnt) & RxEnableWindow;
assign StartShiftWillEnd = LastByteIn  | RxValid & RxEndFrm & (&RxByteCnt) & RxEnableWindow;

// Indicating that data reception will end
always @ (posedge MRxClk or posedge Reset)
begin
  if(Reset)
    ShiftWillEnd <=#Tp 1'b0;
  else
  if(ShiftEnded_tck | RxAbort)
    ShiftWillEnd <=#Tp 1'b0;
  else
  if(StartShiftWillEnd)
    ShiftWillEnd <=#Tp 1'b1;
end



// Receive byte counter
always @ (posedge MRxClk or posedge Reset)
begin
  if(Reset)
    RxByteCnt <=#Tp 2'h0;
  else
  if(ShiftEnded_tck | RxAbort)
    RxByteCnt <=#Tp 2'h0;
  else
  if(RxValid & RxStartFrm & RxBDReady)
    case(RxPointerLatched)  // synopsys parallel_case
      2'h0 : RxByteCnt <=#Tp 2'h1;
      2'h1 : RxByteCnt <=#Tp 2'h2;
      2'h2 : RxByteCnt <=#Tp 2'h3;
      2'h3 : RxByteCnt <=#Tp 2'h0;
    endcase
  else
  if(RxValid & RxEnableWindow & RxBDReady | LastByteIn)
    RxByteCnt <=#Tp RxByteCnt + 1'b1;
end


// Indicates how many bytes are valid within the last word
always @ (posedge MRxClk or posedge Reset)
begin
  if(Reset)
    RxValidBytes <=#Tp 2'h1;
  else
  if(RxValid & RxStartFrm)
    case(RxPointerLatched)  // synopsys parallel_case
      2'h0 : RxValidBytes <=#Tp 2'h1;
      2'h1 : RxValidBytes <=#Tp 2'h2;
      2'h2 : RxValidBytes <=#Tp 2'h3;
      2'h3 : RxValidBytes <=#Tp 2'h0;
    endcase
  else
  if(RxValid & ~LastByteIn & ~RxStartFrm & RxEnableWindow)
    RxValidBytes <=#Tp RxValidBytes + 1;
end


always @ (posedge MRxClk or posedge Reset)
begin
  if(Reset)
    RxDataLatched1       <=#Tp 24'h0;
  else
  if(RxValid & RxBDReady & ~LastByteIn)
    if(RxStartFrm)
    begin
      case(RxPointerLatched)     // synopsys parallel_case
        2'h0:        RxDataLatched1[31:24] <=#Tp RxData;            // Big Endian Byte Ordering
        2'h1:        RxDataLatched1[23:16] <=#Tp RxData;
        2'h2:        RxDataLatched1[15:8]  <=#Tp RxData;
        2'h3:        RxDataLatched1        <=#Tp RxDataLatched1;
      endcase
    end
    else if (RxEnableWindow)
    begin
      case(RxByteCnt)     // synopsys parallel_case
        2'h0:        RxDataLatched1[31:24] <=#Tp RxData;            // Big Endian Byte Ordering
        2'h1:        RxDataLatched1[23:16] <=#Tp RxData;
        2'h2:        RxDataLatched1[15:8]  <=#Tp RxData;
        2'h3:        RxDataLatched1        <=#Tp RxDataLatched1;
      endcase
    end
end

wire SetWriteRxDataToFifo;

// Assembling data that will be written to the rx_fifo
always @ (posedge MRxClk or posedge Reset)
begin
  if(Reset)
    RxDataLatched2 <=#Tp 32'h0;
  else
  if(SetWriteRxDataToFifo & ~ShiftWillEnd)
    RxDataLatched2 <=#Tp {RxDataLatched1[31:8], RxData};              // Big Endian Byte Ordering
  else
  if(SetWriteRxDataToFifo & ShiftWillEnd)
    case(RxValidBytes)  // synopsys parallel_case
//      0 : RxDataLatched2 <=#Tp {RxDataLatched1[31:8],  RxData};       // Big Endian Byte Ordering
//      1 : RxDataLatched2 <=#Tp {RxDataLatched1[31:24], 24'h0};
//      2 : RxDataLatched2 <=#Tp {RxDataLatched1[31:16], 16'h0};
//      3 : RxDataLatched2 <=#Tp {RxDataLatched1[31:8],   8'h0};
      0 : RxDataLatched2 <=#Tp {RxDataLatched1[31:8],  RxData};       // Big Endian Byte Ordering
      1 : RxDataLatched2 <=#Tp {RxDataLatched1[31:24], 24'h0};
      2 : RxDataLatched2 <=#Tp {RxDataLatched1[31:16], 16'h0};
      3 : RxDataLatched2 <=#Tp {RxDataLatched1[31:8],   8'h0};
    endcase
end


reg WriteRxDataToFifoSync1;
reg WriteRxDataToFifoSync2;
reg WriteRxDataToFifoSync3;


// Indicating start of the reception process
//assign SetWriteRxDataToFifo = (RxValid & RxBDReady & ~RxStartFrm & RxEnableWindow & (&RxByteCnt)) | (ShiftWillEnd & LastByteIn & (&RxByteCnt));
assign SetWriteRxDataToFifo = (RxValid & RxBDReady & ~RxStartFrm & RxEnableWindow & (&RxByteCnt)) | (RxValid & RxBDReady & RxStartFrm & (&RxPointerLatched)) | (ShiftWillEnd & LastByteIn & (&RxByteCnt));
/*
always @ (posedge MRxClk or posedge Reset)
begin
  if(Reset)
    WriteRxDataToFifo <=#Tp 1'b0;
  else
  if(SetWriteRxDataToFifo & ~RxAbort)
    WriteRxDataToFifo <=#Tp 1'b1;
  else
  if(WriteRxDataToFifoSync1 | RxAbort)
    WriteRxDataToFifo <=#Tp 1'b0;
end



always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    WriteRxDataToFifoSync1 <=#Tp 1'b0;
  else
  if(WriteRxDataToFifo)
    WriteRxDataToFifoSync1 <=#Tp 1'b1;
  else
    WriteRxDataToFifoSync1 <=#Tp 1'b0;
end

always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    WriteRxDataToFifoSync2 <=#Tp 1'b0;
  else
    WriteRxDataToFifoSync2 <=#Tp WriteRxDataToFifoSync1;
end

wire WriteRxDataToFifo_wb;
assign WriteRxDataToFifo_wb = WriteRxDataToFifoSync1 & ~WriteRxDataToFifoSync2;
*/

always @ (posedge MRxClk or posedge Reset)
begin
  if(Reset)
    WriteRxDataToFifo <=#Tp 1'b0;
  else