eth_wishbone.v

这是一个很好的Verilog 编写的8位RISC CPU源码（可做为MCU）

        6'b10_00_1_x, 6'b01_00_1_x :
          begin
 state <=#Tp 4'h8;
            MasterWbTX <=#Tp 1'b0;  // whatever and no master read or write is needed (ack or err comes finishing previous access)
            MasterWbRX <=#Tp 1'b0;
            m_wb_cyc_o <=#Tp 1'b0;
            m_wb_stb_o <=#Tp 1'b0;
            IncrTxPointer<=#Tp 1'b0;
          end
        6'b10_00_0_1, 6'b01_00_0_1 :
          begin
 state <=#Tp 4'h9;
            MasterWbTX <=#Tp 1'b0;  // Between cyc_cleared request was cleared
            MasterWbRX <=#Tp 1'b0;
            m_wb_cyc_o <=#Tp 1'b0;
            m_wb_stb_o <=#Tp 1'b0;
            IncrTxPointer<=#Tp 1'b0;
          end
        default:                            // Don't touch
          begin
            MasterWbTX <=#Tp MasterWbTX;
            MasterWbRX <=#Tp MasterWbRX;
            m_wb_cyc_o <=#Tp m_wb_cyc_o;
            m_wb_stb_o <=#Tp m_wb_stb_o;
            m_wb_sel_o <=#Tp m_wb_sel_o;
            IncrTxPointer<=#Tp IncrTxPointer;
          end
      endcase
    end
end


wire TxFifoClear;

assign TxFifoClear = (TxAbort_wb | TxRetry_wb) & ~TxBDReady;
wire [4:0] txfifo_cnt;

eth_fifo #(`TX_FIFO_DATA_WIDTH, `TX_FIFO_DEPTH, `TX_FIFO_CNT_WIDTH)
tx_fifo ( .data_in(m_wb_dat_i),                             .data_out(TxData_wb), 
          .clk(WB_CLK_I),                                   .reset(Reset), 
          .write(MasterWbTX & m_wb_ack_i),                  .read(ReadTxDataFromFifo_wb), 
          .clear(TxFifoClear),                              .full(TxBufferFull), 
          .almost_full(TxBufferAlmostFull),                 .almost_empty(TxBufferAlmostEmpty), 
          .empty(TxBufferEmpty),                            .cnt(txfifo_cnt)
        );


reg StartOccured;
reg TxStartFrm_sync1;
reg TxStartFrm_sync2;
reg TxStartFrm_syncb1;
reg TxStartFrm_syncb2;



// Start: Generation of the TxStartFrm_wb which is then synchronized to the MTxClk
always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    TxStartFrm_wb <=#Tp 1'b0;
  else
  if(TxBDReady & ~StartOccured & (TxBufferFull | TxLengthEq0))
    TxStartFrm_wb <=#Tp 1'b1;
  else
  if(TxStartFrm_syncb2)
    TxStartFrm_wb <=#Tp 1'b0;
end

// StartOccured: TxStartFrm_wb occurs only ones at the beginning. Then it's blocked.
always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    StartOccured <=#Tp 1'b0;
  else
  if(TxStartFrm_wb)
    StartOccured <=#Tp 1'b1;
  else
  if(ResetTxBDReady)
    StartOccured <=#Tp 1'b0;
end

// Synchronizing TxStartFrm_wb to MTxClk
always @ (posedge MTxClk or posedge Reset)
begin
  if(Reset)
    TxStartFrm_sync1 <=#Tp 1'b0;
  else
    TxStartFrm_sync1 <=#Tp TxStartFrm_wb;
end

always @ (posedge MTxClk or posedge Reset)
begin
  if(Reset)
    TxStartFrm_sync2 <=#Tp 1'b0;
  else
    TxStartFrm_sync2 <=#Tp TxStartFrm_sync1;
end

always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    TxStartFrm_syncb1 <=#Tp 1'b0;
  else
    TxStartFrm_syncb1 <=#Tp TxStartFrm_sync2;
end

always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    TxStartFrm_syncb2 <=#Tp 1'b0;
  else
    TxStartFrm_syncb2 <=#Tp TxStartFrm_syncb1;
end

always @ (posedge MTxClk or posedge Reset)
begin
  if(Reset)
    TxStartFrm <=#Tp 1'b0;
  else
  if(TxStartFrm_sync2)
    TxStartFrm <=#Tp 1'b1;
  else
  if(TxUsedData_q | ~TxStartFrm_sync2 & (TxRetry | TxAbort))
    TxStartFrm <=#Tp 1'b0;
end
// End: Generation of the TxStartFrm_wb which is then synchronized to the MTxClk


// TxEndFrm_wb: indicator of the end of frame
always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    TxEndFrm_wb <=#Tp 1'b0;
  else
  if(TxLengthLt4 & TxBufferAlmostEmpty & TxUsedData)
    TxEndFrm_wb <=#Tp 1'b1;
  else
  if(TxRetryPulse | TxDonePulse | TxAbortPulse)
    TxEndFrm_wb <=#Tp 1'b0;
end


// Marks which bytes are valid within the word.
assign TxValidBytes = TxLengthLt4 ? TxLength[1:0] : 2'b0;

reg LatchValidBytes;
reg LatchValidBytes_q;

always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    LatchValidBytes <=#Tp 1'b0;
  else
  if(TxLengthLt4 & TxBDReady)
    LatchValidBytes <=#Tp 1'b1;
  else
    LatchValidBytes <=#Tp 1'b0;
end

always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    LatchValidBytes_q <=#Tp 1'b0;
  else
    LatchValidBytes_q <=#Tp LatchValidBytes;
end


// Latching valid bytes
always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    TxValidBytesLatched <=#Tp 2'h0;
  else
  if(LatchValidBytes & ~LatchValidBytes_q)
    TxValidBytesLatched <=#Tp TxValidBytes;
  else
  if(TxRetryPulse | TxDonePulse | TxAbortPulse)
    TxValidBytesLatched <=#Tp 2'h0;
end


assign TxIRQEn          = TxStatus[14];
assign WrapTxStatusBit  = TxStatus[13];
assign PerPacketPad     = TxStatus[12];
assign PerPacketCrcEn   = TxStatus[11];


assign RxIRQEn         = RxStatus[14];
assign WrapRxStatusBit = RxStatus[13];


// Temporary Tx and Rx buffer descriptor address 
assign TempTxBDAddress[7:0] = {8{ TxStatusWrite     & ~WrapTxStatusBit}} & (TxBDAddress + 2'h2) ; // Tx BD increment or wrap (last BD)
assign TempRxBDAddress[7:0] = {8{ WrapRxStatusBit}} & (r_TxBDNum<<1)     | // Using first Rx BD
                              {8{~WrapRxStatusBit}} & (RxBDAddress + 2'h2) ; // Using next Rx BD (incremenrement address)


// Latching Tx buffer descriptor address
always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    TxBDAddress <=#Tp 8'h0;
  else
  if(TxStatusWrite)
    TxBDAddress <=#Tp TempTxBDAddress;
end


// Latching Rx buffer descriptor address
always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    RxBDAddress <=#Tp `ETH_TX_BD_NUM_DEF<<1;
  else
  if(TX_BD_NUM_Wr)                        // When r_TxBDNum is updated, RxBDAddress is also
    RxBDAddress <=#Tp WB_DAT_I[7:0]<<1;
  else
  if(RxStatusWrite)
    RxBDAddress <=#Tp TempRxBDAddress;
end

wire [8:0] TxStatusInLatched = {TxUnderRun, RetryCntLatched[3:0], RetryLimit, LateCollLatched, DeferLatched, CarrierSenseLost};

assign RxBDDataIn = {LatchedRxLength, 1'b0, RxStatus, 6'h0, RxStatusInLatched};
assign TxBDDataIn = {LatchedTxLength, 1'b0, TxStatus, 2'h0, TxStatusInLatched};


// Signals used for various purposes
assign TxRetryPulse   = TxRetry_wb   & ~TxRetry_wb_q;
assign TxDonePulse    = TxDone_wb    & ~TxDone_wb_q;
assign TxAbortPulse   = TxAbort_wb   & ~TxAbort_wb_q;
assign TxRetryPulse_q = TxRetry_wb_q & ~TxRetry_wb_q2;
assign TxDonePulse_q  = TxDone_wb_q  & ~TxDone_wb_q2;
assign TxAbortPulse_q = TxAbort_wb_q & ~TxAbort_wb_q2;



// Generating delayed signals
always @ (posedge MTxClk or posedge Reset)
begin
  if(Reset)
    begin
      TxAbort_q      <=#Tp 1'b0;
      TxRetry_q      <=#Tp 1'b0;
      TxUsedData_q   <=#Tp 1'b0;
    end
  else
    begin
      TxAbort_q      <=#Tp TxAbort;
      TxRetry_q      <=#Tp TxRetry;
      TxUsedData_q   <=#Tp TxUsedData;
    end
end

// Generating delayed signals
always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    begin
      TxDone_wb_q   <=#Tp 1'b0;
      TxAbort_wb_q  <=#Tp 1'b0;
      TxRetry_wb_q  <=#Tp 1'b0;
      TxDone_wb_q2  <=#Tp 1'b0;
      TxAbort_wb_q2 <=#Tp 1'b0;
      TxRetry_wb_q2 <=#Tp 1'b0;
    end
  else
    begin
      TxDone_wb_q   <=#Tp TxDone_wb;
      TxAbort_wb_q  <=#Tp TxAbort_wb;
      TxRetry_wb_q  <=#Tp TxRetry_wb;
      TxDone_wb_q2  <=#Tp TxDone_wb_q;
      TxAbort_wb_q2 <=#Tp TxAbort_wb_q;
      TxRetry_wb_q2 <=#Tp TxRetry_wb_q;
    end
end


// Sinchronizing and evaluating tx data
//assign SetGotData = (TxStartFrm_wb | NewTxDataAvaliable_wb & ~TxAbort_wb & ~TxRetry_wb) & ~WB_CLK_I;
assign SetGotData = (TxStartFrm_wb); // igor namesto zgornje

// Evaluating data. If abort or retry occured meanwhile than data is ignored.
//assign GotDataEvaluate = GotDataSync3 & ~GotData & (~TxRetry & ~TxAbort | (TxRetry | TxAbort) & (TxStartFrm));
assign GotDataEvaluate = (~TxRetry & ~TxAbort | (TxRetry | TxAbort) & (TxStartFrm));


// Indication of the last word
always @ (posedge MTxClk or posedge Reset)
begin
  if(Reset)
    LastWord <=#Tp 1'b0;
  else
  if((TxEndFrm | TxAbort | TxRetry) & Flop)
    LastWord <=#Tp 1'b0;
  else
  if(TxUsedData & Flop & TxByteCnt == 2'h3)
    LastWord <=#Tp TxEndFrm_wb;
end


// Tx end frame generation
always @ (posedge MTxClk or posedge Reset)
begin
  if(Reset)
    TxEndFrm <=#Tp 1'b0;
  else
  if(Flop & TxEndFrm | TxAbort | TxRetry_q)
    TxEndFrm <=#Tp 1'b0;        
  else
  if(Flop & LastWord)
    begin
      case (TxValidBytesLatched)  // synopsys parallel_case
        1 : TxEndFrm <=#Tp TxByteCnt == 2'h0;
        2 : TxEndFrm <=#Tp TxByteCnt == 2'h1;
        3 : TxEndFrm <=#Tp TxByteCnt == 2'h2;
        0 : TxEndFrm <=#Tp TxByteCnt == 2'h3;
        default : TxEndFrm <=#Tp 1'b0;
      endcase
    end
end


// Tx data selection (latching)
always @ (posedge MTxClk or posedge Reset)
begin
  if(Reset)
    TxData <=#Tp 0;
  else
  if(TxStartFrm_sync2 & ~TxStartFrm)
    case(TxPointerLatched)  // synopsys parallel_case
      2'h0 : TxData <=#Tp TxData_wb[31:24];                  // Big Endian Byte Ordering
      2'h1 : TxData <=#Tp TxData_wb[23:16];                  // Big Endian Byte Ordering
      2'h2 : TxData <=#Tp TxData_wb[15:08];                  // Big Endian Byte Ordering
      2'h3 : TxData <=#Tp TxData_wb[07:00];                  // Big Endian Byte Ordering
    endcase
  else
  if(TxStartFrm & TxUsedData & TxPointerLatched==2'h3)
    TxData <=#Tp TxData_wb[31:24];                           // Big Endian Byte Ordering
  else
  if(TxUsedData & Flop)
    begin
      case(TxByteCnt)  // synopsys parallel_case
        0 : TxData <=#Tp TxDataLatched[31:24];      // Big Endian Byte Ordering
        1 : TxData <=#Tp TxDataLatched[23:16];
        2 : TxData <=#Tp TxDataLatched[15:8];
        3 : TxData <=#Tp TxDataLatched[7:0];
      endcase
    end
end


// Latching tx data
always @ (posedge MTxClk or posedge Reset)
begin
  if(Reset)
    TxDataLatched[31:0] <=#Tp 32'h0;
  else
 if(TxStartFrm_sync2 & ~TxStartFrm | TxUsedData & Flop & TxByteCnt == 2'h3 | TxStartFrm & TxUsedData & Flop & TxByteCnt == 2'h0)
    TxDataLatched[31:0] <=#Tp TxData_wb[31:0];
end


// Tx under run
always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    TxUnderRun_wb <=#Tp 1'b0;
  else
  if(TxAbortPulse)
    TxUnderRun_wb <=#Tp 1'b0;
  else
  if(TxBufferEmpty & ReadTxDataFromFifo_wb)
    TxUnderRun_wb <=#Tp 1'b1;
end


// Tx under run
always @ (posedge MTxClk or posedge Reset)
begin
  if(Reset)
    TxUnderRun <=#Tp 1'b0;
  else
  if(TxUnderRun_wb)
    TxUnderRun <=#Tp 1'b1;
  else
  if(BlockingTxStatusWrite)
    TxUnderRun <=#Tp 1'b0;
end


// Tx Byte counter
always @ (posedge MTxClk or posedge Reset)
begin
  if(Reset)
    TxByteCnt <=#Tp 2'h0;
  else
  if(TxAbort_q | TxRetry_q)
    TxByteCnt <=#Tp 2'h0;
  else
  if(TxStartFrm & ~TxUsedData)
    case(TxPointerLatched)  // synopsys parallel_case
      2'h0 : TxByteCnt <=#Tp 2'h1;
      2'h1 : TxByteCnt <=#Tp 2'h2;
      2'h2 : TxByteCnt <=#Tp 2'h3;
      2'h3 : TxByteCnt <=#Tp 2'h0;
    endcase
  else
  if(TxUsedData & Flop)
    TxByteCnt <=#Tp TxByteCnt + 1'b1;
end

/*
// Start: Generation of the ReadTxDataFromFifo_tck signal and synchronization to the WB_CLK_I
reg ReadTxDataFromFifo_sync1;
reg ReadTxDataFromFifo_sync2;
reg ReadTxDataFromFifo_sync3;
reg ReadTxDataFromFifo_syncb1;
reg ReadTxDataFromFifo_syncb2;


always @ (posedge MTxClk or posedge Reset)
begin
  if(Reset)
    ReadTxDataFromFifo_tck <=#Tp 1'b0;
  else
  if(TxStartFrm_sync2 & ~TxStartFrm | TxUsedData & Flop & TxByteCnt == 2'h3 & ~LastWord | TxStartFrm & TxUsedData & Flop & TxByteCnt == 2'h0)
     ReadTxDataFromFifo_tck <=#Tp 1'b1;
  else
  if(ReadTxDataFromFifo_syncb2)
    ReadTxDataFromFifo_tck <=#Tp 1'b0;
end

// Synchronizing TxStartFrm_wb to MTxClk
always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    ReadTxDataFromFifo_sync1 <=#Tp 1'b0;
  else
    ReadTxDataFromFifo_sync1 <=#Tp ReadTxDataFromFifo_tck;
end

always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    ReadTxDataFromFifo_sync2 <=#Tp 1'b0;
  else
    ReadTxDataFromFifo_sync2 <=#Tp ReadTxDataFromFifo_sync1;
end

always @ (posedge MTxClk or posedge Reset)
begin
  if(Reset)
    ReadTxDataFromFifo_syncb1 <=#Tp 1'b0;
  else
    ReadTxDataFromFifo_syncb1 <=#Tp ReadTxDataFromFifo_sync2;
end

always @ (posedge MTxClk or posedge Reset)
begin
  if(Reset)
    ReadTxDataFromFifo_syncb2 <=#Tp 1'b0;
  else
    ReadTxDataFromFifo_syncb2 <=#Tp ReadTxDataFromFifo_syncb1;
end

always @ (posedge WB_CLK_I or posedge Reset)
begin
  if(Reset)
    ReadTxDataFromFifo_sync3 <=#Tp 1'b0;
  else
    ReadTxDataFromFifo_sync3 <=#Tp ReadTxDataFromFifo_sync2;