提出一种基于凌阳单片机的步进电机加减速的控制方法。采用凌阳科技推出的16位结构工控单片机SPMC75F2413A为控制器，由Allegro公司生产的两相步进电机专用驱动器件SLA7042M构成步进电机的驱动电路，在传统的3段直线加减速控制算法基础上增加至7段S形曲线加减速过程，控制步进电机的启动和停止。实验结果表明，该控制方法克服了直线加减速中不连续、易造成系统冲击的问题，整个系统实现柔性控制，电机启动、停止连续性能提高30%。 Abstract: The method of controlled stepping motor is referred based on SPMC75F2413A MCU， which adopts the 16 knots SPMC75F2413A MCU as the controller. The special-purpose actuation chip SLA7042M of two stepping motor produced by Allegro Corporation constituted to actuation electric circuit. The purpose of increasing to seven section of S shape curve based on the traditional three sections of straight line is to control the start and stop process of stepping motor. The experimental results show that the control method solves easy to pull-out and overshot problems. The overall system realizes flexible control， and the performance of motor start or stop continuity is increased 30%
上传时间： 2013-12-08
上传用户：jiangfire
介绍一种基于C8051单片机的动态心电监护系统。该系统由两部分组成：以C8051F320单片机为核心的数据采集装置和以PC机为平台的分析处理系统。硬件电路功耗低，由单片机自带的USB接口将数据传送给PC机。软件平台采用LabVIEW可视化虚拟仪器系统开发平台，将传统仪器的功能模块集成到计算机中，用户可通过修改虚拟仪器的程序改变其功能。采用USB接口实时传输心电数据，并将数据采集模块设计为计算机外设，使该系统高速快捷、小巧便携。 Abstract: In this design，a low-cost ECG electrocardiogram monitoring system is introduced，which consists of two parts:data acquisition device based on C8051F320and PC terminal as the analysis and processing system.The system is low-power consumption，the data is transmitted to the PC terminal by USB interface of the C8051F320.By using the visible virtual instrument system developing platform LabVIEW，the traditional instruments function modules are integrated into the computer，so the user can modify virtual instrument software to change its function to meet their needs.Using USB in-terface to realize real-time ECG data transmission，in addition，ECG data acquisition module is designed as the computer peripheral，which makes the syetem high-speed and portable.
上传时间： 2013-11-13
上传用户：zhangzhenyu
介绍一种基于CAN总线的牵引变电站自动化系统通讯规约的设计，CAN通讯规约采用标准帧，报文采用主动发送和发送查询两种处理形式。该设计在城市轻轨与地铁牵引变电站中的应用表明：可实现间隔层和通讯处理层的数据快速、可靠的交换，提高牵引变电站的安全性和稳定性 。 Abstract: This paper firstly presents a kind of design dealing with communicational protocol to the traction substation automation system based on CAN bus,and then comes up with the ideas that all frames of CAN communicational protocol should adopt the standard frame,and that messages be processed by two ways:sending initiatively and sending quiries.Subway and light rail application shows that the use of the CAN bus is possible to exchange data quickly and reliably between the layers of the middle and the communicational processing,hence to improve the safety and stability of traction substations.
上传时间： 2013-11-07
上传用户：bs2005
介绍一种多功能音乐播放器，它是以AT89S52单片机为核心，并辅有一些外围器件，采用汇编语言编写程序，实现多功能音乐播放，歌曲自动循环播放和使用琴键自编曲目功能。此外，彩灯显示歌曲节奏，按键跳转到喜爱曲目，液晶显示当前播英文曲目。并给出了系统软硬件设计。 Abstract: It introduces a multifunctional music player,taking AT89S52 single-chip microcomputer as hardware control core and using some peripheral elements.Programmes are compiled in assembly language to act as expected.There are two functional modes in this system.One is to make the music play automatically and consecutively,the other is to compose new songs through keys.In addition,lights show the pace of music and the English names can be displayed in the liquid crystal screen.With perfect combination of hardware and software,the music player can meet many music lovers’needs for multifunctional music player.And the hardware and software of the system are given.
上传时间： 2013-11-18
上传用户：xiaodu1124
从系统硬件设计和软件构成上，介绍一种以AT89C52单片机为核心,通过无线遥控方法实现对预设电话自动拨号报警的智能呼救系统。系统提供了患者在紧急情况下无法使用电话报警时的一种报警手段。由用户预设的多组电话号码作为语音报警对象,预录可长达20 s的语音信号来说明患者所处地点及病情，并通知患者家人。 Abstract: This paper introduces a intelligent alarming system which is realized by wireless remote control system.This system chiefly consists of AT89C51 the system can processor.User can input several groups of telephone number regarded as alarming objects,The system can record some information 20 seconds to tell the site of the patient.And notice the rokonok of the patient.
上传时间： 2013-11-19
上传用户：wd450412225
对于传统的跑步机无法联机组网，保存历史数据，实时调试等问题，介绍了一个由多台跑步机通过RS-232串行总线与上位机相连组成的跑步机联网系统。系统采用W77E58作为下位机核心控制器件，它具有双串行通讯端口，其中一个串口用于与变频器通讯，另一个串口则与上位机相连，构成跑步机网络。 Abstract: The traditional running machine can not be connected to a network, saving historical data, real time debug etc.In this paper,a new network system which is composed of running machines connected by a RS-232 communication bus is introduced.In the system,W77E58 is used as a core control unit.W77E58 has two serial ports,one is connected to the inverter and the other is connected to the PC. Thus a network appears.
上传时间： 2014-12-27
上传用户：哇哇哇哇哇
为深入了解基于UC3854A控制的PFC变换器中的动力学特性，研究系统参数变化对变换器中分岔现象的影响，在建立Boost PFC变换器双闭环数学模型的基础上，用Matlab软件对变换器中慢时标分岔及混沌等不稳定现象进行了仿真。在对PFC变换器中慢时标分岔现象仿真的基础上，分析了系统参数变化对分岔点的影响，并进行了仿真验证。仿真结果清晰地显示了输入整流电压的幅值变化对系统分岔点的影响。 Abstract: In order to better understand the dynamics characteristic of power factor correction converter based on UC3854A， and make the way that parameters change influences the bifurcation phenomena of the system clearly. The math model of the two closed loop circuits to the Boost PFC （Power Factor Correction） converter controller was built. Then， with the help of Matlab， the simulation for nonlinear phenomena such as chaos and slow-scale bifurcation in the PFC converter was made. Finally the factors that have influence to the phenomenon of bifurcation under slow-scale in PFC converter were analyzed. The simulation results clearly show the parameters change influences the bifurcation point of the system.
上传时间： 2013-10-17
上传用户：杜莹12345
为降低成本和解决现有膜片钳放大器系统中PC机的干扰问题，研究了一种基于单片机的膜片钳放大器小系统。该系统采用ADI公司生产的ADuC841作为控制核心，并且配置相应的液晶显示模块LCM3202401。模拟电路部分采用高输入阻抗的AD8627实现微电流信号的采集，并由后级电路进行信号的放大和电阻电容的补偿。它具有硬件电路简单、体积小、使用方便的特点。既可以单独作为小系统实现采集和显示，也可以通过红外方式和PC机进行通讯，在PC机上进行信号的处理。 Abstract: In order to reduce cost and resolve the interferential problem with PC in existing patch clamp amplifiers, a small patch clamp amplifier system design based on microcontroller is studied. It adopts a new high performance microconverter ADuC841 by the ADI as the control core in the system, configuring a liquid crystal module LCM3202401. In the analog circuit, AD8627 with high input impedance is used to detect the low current，signal magnification, as well as resistance and capacitance compensation are accomplished by subsequent circuits. It has the advantage of simple hardware circuit design, small volume and convenient operation. It can either be used as an independent system to measure and show signal detected or transmit to PC by infrared ray.
上传时间： 2013-11-06
上传用户：yy_cn
基于幅移键控技术ASK（Amplitude-Shift Keying），以C8051F340单片机作为监测终端控制器，C8051F330D单片机作为探测节点控制器，采用半双工的通信方式，通过监控终端和探测节点的无线收发电路，实现数据的双向无线传输。收发电路采用直径为0.8 mm的漆包线自行绕制成圆形空心线圈天线，天线直径为（3.4±0.3）cm。试验表明，探测节点与监测终端的通信距离为24 cm，通过桥接方式，节点收发功率为102 mW时，节点间的通信距离可达20 cm。与传统无线收发模块相比，该无线收发电路在受体积、功耗、成本限制的场合有广阔的应用前景。 Abstract: Based on ASK technology and with the C8051F340 and C8051F330D MCU as the controller， using half-duplex communication mode， this paper achieves bi-directional data transfer. Transceiver circuit constituted by enameled wire which diameter is 0.8mm and wound into a diameter （3.4±0.3） cm circular hollow coil antenna. Tests show that the communication distance between detection and monitoring of the terminal is 24cm，the distance is up to 20cm between two nodes when using the manner of bridging and the node transceiver power is 102mW. Compared with the conventional wireless transceiver modules， the circuit has wide application prospect in small size， low cost and low power consumption and other characteristics.
上传时间： 2013-10-19
上传用户：xz85592677
在需要实时大量输入汉字的显示控制处理应用中，利用传统单片机实现显示控制的设计方法是较难实现的。带汉字字库的液晶模块的使用使得小容量ROM单片机的大量汉字信息输入与显示成为可能。提出了针对汉字字库编码的二级索引拼音输入检索方法,介绍了以ST7920作为控制器的带汉字字库的液晶显示模块的接口方法及汉字显示和控制原理，给出了通用计算机键盘在单片机中的串行接口，采用该技术可大大增强单片机的汉字输入功能。为小容量ROM单片机的大批量汉字信息处理提供了一种汉字输入解决方案。 Abstract: It is difficult to realize Chinese characters input method based on the embedded system by using the traditional design method of display control. It is possible to input and display Chinese characters based on the embedded system with the ROM of small content by using the LCD module with Chinese characters.Chinese characters input method of the quadric index recall in allusion to Chinese characters code is brought forward.The interface and the principle of Chinese characters display control based on the LCD module controlled with the ST7920 is introduced too.The serial interface of the computer keyboard in common use and the embedded system is given at the same time. It can enhance the embedded system function of Chinese characters input by using this technology, and provide a kind of Chinese characters input scheme for the embedded system with small capacity ROM.
上传时间： 2013-11-19
上传用户：jhksyghr
