分析了调幅信号和载波信号之间的相位差与调制信号的极性的对应关系,得出了相敏检波电路输出电压的极性与调制信号的极性有对应关系的结论。为了验证相敏检波电路的这一特性,给出3 个电路方案,分别选用理想元件和实际元件,采用Multisim 对其进行仿真实验,直观形象地演示了相敏检波电路的鉴相特性,是传统的实际操作实验所不可比拟的。关键词:相敏检波;鉴相特性;Multisim;电路仿真 Abstract : The corresponding relation between modulation signal polarity and difference phases of amplitudemodulated signal and the carrier signal ,the polarity of phase2sensitive detecting circuit output voltage and the polarity of modulation signal are correspondent . In order to verify this characteristic ,three elect ric circuit s plans are produced ,idea element s and actual element s are selected respectively. Using Multisim to carry on a simulation experiment ,and then demonst rating the phase detecting characteristic of the phase sensitive circuit vividly and directly. Which is t raditional practical experience cannot be com pared.Keywords :phase sensitive detection ;phase2detecting characteristic ;Multisim;circuit simulation
上传时间： 2013-11-23
上传用户：guanhuihong
Radio Frequency Integrated Circuit Design I enjoyed reading this book for a number of reasons. One reason is that itaddresses high-speed analog design in the context of microwave issues. This isan advanced-level book, which should follow courses in basic circuits andtransmission lines. Most analog integrated circuit designers in the past workedon applications at low enough frequency that microwave issues did not arise.As a consequence, they were adept at lumped parameter circuits and often notcomfortable with circuits where waves travel in space. However, in order todesign radio frequency (RF) communications integrated circuits (IC) in thegigahertz range, one must deal with transmission lines at chip interfaces andwhere interconnections on chip are far apart. Also, impedance matching isaddressed, which is a topic that arises most often in microwave circuits. In mycareer, there has been a gap in comprehension between analog low-frequencydesigners and microwave designers. Often, similar issues were dealt with in twodifferent languages. Although this book is more firmly based in lumped-elementanalog circuit design, it is nice to see that microwave knowledge is brought inwhere necessary.Too many analog circuit books in the past have concentrated first on thecircuit side rather than on basic theory behind their application in communications.The circuits usually used have evolved through experience, without asatisfying intellectual theme in describing them. Why a given circuit works bestcan be subtle, and often these circuits are chosen only through experience. Forthis reason, I am happy that the book begins first with topics that require anintellectual approach—noise, linearity and filtering, and technology issues. Iam particularly happy with how linearity is introduced (power series). In therest of the book it is then shown, with specific circuits and numerical examples,how linearity and noise issues arise.
上传时间： 2014-12-23
上传用户：han_zh
Abstract: We can apply a BiCMOS integrated circuit with only resistors and no transistors to solve adifficult design problem. The mythically perfect operational amplifier's gain and temperature coefficient aredependent on external resistor values. Maxim precision resistor arrays are manufactured together on asingle die and then automatically trimmed, to ensure close ratio matching. This guarantees that theoperational amplifier (op amp) gain and temperature coefficient are predictable and reliable, even withlarge production volumes.
上传时间： 2014-11-30
上传用户：ynzfm
Abstract: The DS1875 features a pulse-width modulation (PWM) controller that can be used to control aDC-DC converter. The DC-DC converter can then be used to generate the high bias voltages necessaryfor avalanche photodiodes (APDs). This application note describes the operation of a boost converterthat uses the DS1875. Discussion covers the selection of the inductor and switching frequency, and theselection of components that improve the efficiency of the converter. Test data are presented.
上传时间： 2013-10-26
上传用户：lyson
锁定放大是微弱信号检测的重要手段。基于相关检测理论，利用开关电容的开关实现锁定放大器中乘法器的功能，提出开关电容和积分器相结合以实现相关检测的方法，并设计出一种锁定放大器。该锁定放大器将微弱信号转化为与之相关的方波，通过后续电路得到正比于被测信号的直流电平，为后续采集处理提供方便。测量数据表明锁定放大器前级可将10-6 A的电流转换为10-1 V的电压，后级通过带通滤波器级联可将信号放大1×105倍。该方法在降低噪声的同时，可对微弱信号进行放大，线性度较高、稳定性较好。 Abstract: Lock-in Amplifying（LIA）is one of important means for weak signal detection. Based on cross-correlation detection theory， switch in the swithched capacitor was used as multiplier of LIA， and a new method of correlation detection was proposed combining swithched capacitor with integrator. A kind of LIA was designed which can convert the weak signal to square-wave， then DC proportional to measured signal was obtained through follow-up conditioning circuit， providing convenience for signal acquisition and processing. The measured data shows that the electric current（10-6 A） can be changed into voltage（10-1 V） by LIA， and the signal is magnified 1×105 times by cascade band-pass filter. The noise is suppressed and the weak signal is amplified. It has the advantages of good linearity and stability.
上传时间： 2013-11-29
上传用户：黑漆漆
针对煤矿井下调度及紧急救援系统的需求，以DTMF编解码模块为核心，设计了具有自动拨号功能的新型电话系统。该系统利用MT8880对DTMF信号的编解码功能实现一键拨号和远程设置，通过检测振铃和忙音信号，完成自动摘机和挂机过程，配合AGC等外围电路达到话音清晰流畅的效果。 Abstract: To meet the demand for mine scheduling and emergency rescue system， with using DTMF signal codec as the core， a new telephone system was designed with automatic dialing function. In the system， the DTMF signal encoding and decoding function of MT8880 was used to achieve one-touch dialing and remote setting. The circuit detects the ringing and busy signal， and then completes automatic off-hook and hangup. With AGC(Automatic Gain Control) and other peripheral circuits， the voice was regulated to a clear and smooth effect.
上传时间： 2014-11-18
上传用户：ly1994
为了使音频信号分析仪小巧可靠，成本低廉，设计了以2片MSP430F1611单片机为核心的系统。该系统将音频信号送入八阶巴特沃兹低通滤波器，对信号进行限幅放大、衰减、电平位移、缓冲，并利用一单片机负责对前级处理后的模拟信号进行采样，将采集得到的音频信号进行4 096点基2的FFT计算，并对信号加窗函数提高分辨率，另一单片机负责对信号的分析及控制显示设备。此设计精确的测量了音频信号的功率谱、周期性、失真度指标，达到较高的频率分辨率，并能将测量结果通过红外遥控器显示在液晶屏上。 Abstract: o make the audio signal analyzer cheaper， smaller and more reliable， this system sends the audio signal to the eight-order butterworth filter， and then amplifies， attenuates， buffers it in a limiting range， transfers the voltage level of the signal before utilizing two MSP430F1611 MCU to realize the audio analysis. One is charged for sampling and dealing with the processed audio signal collected by the 4096 point radix-2 FFT calculation and imposes the window function to improve the frequency resolution. The other one controls the display and realizes the spectrum， periodicity， power distortion analysis in high resolution which is displayed in the LCD screen through the infrared remote control.
上传时间： 2013-12-11
上传用户：jasonheung
介绍一种基于CAN总线的牵引变电站自动化系统通讯规约的设计，CAN通讯规约采用标准帧，报文采用主动发送和发送查询两种处理形式。该设计在城市轻轨与地铁牵引变电站中的应用表明：可实现间隔层和通讯处理层的数据快速、可靠的交换，提高牵引变电站的安全性和稳定性 。 Abstract: This paper firstly presents a kind of design dealing with communicational protocol to the traction substation automation system based on CAN bus,and then comes up with the ideas that all frames of CAN communicational protocol should adopt the standard frame,and that messages be processed by two ways:sending initiatively and sending quiries.Subway and light rail application shows that the use of the CAN bus is possible to exchange data quickly and reliably between the layers of the middle and the communicational processing,hence to improve the safety and stability of traction substations.
上传时间： 2013-11-07
上传用户：bs2005
介绍一种简单射频识别系统设计。该设计包括阅读器、应答器和线圈3部分。由单片机控制阅读器向应答器发射无线信号，并接收应答器回送的信号，再通过分析回送信号识别物品。阅读器和应答器之间以半双工通信方式通信。 Abstract: A simple design of radio frequency identification system is given in this paper.The design includes reader,responder and winding.Through MCU，signals are sent to responder from reader，then corresponding signals are sent back. According to the analysis of the signals sent back，the objects can be identified.Half-duplex communication is adopted? between? reader? and? responder.
上传时间： 2013-10-11
上传用户：plsee
介绍一种采用单片机技术和基站器件EM4095的手持式低频RFID读卡器方案。首先对整个系统框架进行说明，然后介绍主要功能模块的设计，给出了各模块的原理图。重点描述了基站器件EM4095的性能参数和功能原理，最后描述了该系统的主程序流程图。 Abstract: In this paper,a handheld RFID reader based on MCU and EM4095 is introduced.At first，the configuration of this system is explained.then the design of main modules and schematic documents are particularly presented.The parameters and principle of the chip EM4095 are introduced in detail. At last，the main software flow is given
上传时间： 2013-10-18
上传用户：windypsm
