This document gives the code for programming a CC2500 transceiver using Altera Stratix FPGA. The FPGA and CC2500 are connected through SPI mode with the FPGA as the master and CC2500 as the slave.
标签： programming transceiver document Stratix
上传时间： 2014-01-15
上传用户：wuyuying
本函数在matlab实现阻抗圆图，通过调用switch（）函数，可以得出传输线的反射系数，以及支节匹配等参数，本函数可以实现单、双和三支节匹配。
上传时间： 2014-01-06
上传用户：jennyzai
This program requires the DSP2833x header files. // // This program requires an external I2C RTC connected to // the I2C bus at address 0x6f. // // As supplied, this project is configured for "boot to SARAM" // operation. The 2833x Boot Mode table is shown below. // For information on configuring the boot mode of an eZdsp, // please refer to the documentation included with the eZdsp,
标签： requires program This external
上传时间： 2017-07-12
上传用户：dianxin61
This program requires the DSP2833x header files. // // As supplied, this project is configured for "boot to SARAM" // operation. The 2833x Boot Mode table is shown below. // For information on configuring the boot mode of an eZdsp, // please refer to the documentation included with the eZdsp,
标签： configured requires supplied program
上传时间： 2014-01-10
上传用户：lixinxiang
此题目是通过键盘来实现密码输入是否正确，正确的时候数码管亮，否则发出报警声。 判断是按键还是干扰是非常有用的，它体现了一个系统的抗干扰能力。高低电平在瞬间的变换是很正常的，如果没有这条语句，系统很容易出错。 其中2秒是由定时器0来完成的。 在程序的定时器中断中，用switch代替了if else结构，使得程序的可读性大大增强。 TH0 = (65536-50000) / 256 TL0 = (65536-50000) 256 使得TH0 = 3CH, TL0 = B0H,由于该单片机的晶振为12MHz 因此定时时间就为0.05ms.在定时器中断服务程序中用FLASH计数，当计数达到40时正好是2秒。
上传时间： 2014-01-21
上传用户：caozhizhi
This software is developed to provide ease with controller design. For PID control, options are given to design and analyse the compensated and uncompensated system. You are free to choice among Proportional PI, PD and PID mode of control. Both frequency and time domain characteristics can be observed. Special Menus are given to observe time and frequency response plots. For Statefeedback controller similar options are given. But this is limited to second order system only.
标签： controller developed software control
上传时间： 2017-07-25
上传用户：aysyzxzm
RS_latch using vhdl, When using static gates as building blocks, the most fundamental latch is the simple SR latch, where S and R stand for set and reset. It can be constructed from a pair of cross-coupled NOR (Not OR) logic gates. The stored bit is present on the output marked Q. Normally, in storage mode, the S and R inputs are both low, and feedback maintains the Q and Q outputs in a constant state, with Q the complement of Q. If S (Set) is pulsed high while R is held low, then the Q output is forced high, and stays high when S returns to low similarly, if R (Reset) is pulsed high while S is held low, then the Q output is forced low, and stays low when R returns to low.
标签： using fundamental the RS_latch
上传时间： 2017-07-30
上传用户：努力努力再努力
hese are the zip files that are associated with application note ADSP-BF533 Blackfin Booting Process (EE-240) example.zip: Used throughout the EE-note to explain in detail the various booting modes. BF533 Ez Kit Multiple DXE Boot.zip: Multi-DXE Boot Example used with the ADSP-BF533 Ez-Kit Lite. Host Boot.zip: Example Host code to demonstrate SPI Slave Mode Booting Program_Atmel.zip: Example code that programs the Atmel DataFlashes via an ADSP-BF532 Processor All programs have been written for VisualDSP++ 3.5
标签： application associated are Blackfin
上传时间： 2017-07-30
上传用户：tonyshao
矩阵键盘程序，主要教会初学者练习switch语句，同时练习条件语句，用于键盘扫描
标签： 矩阵键盘程序
上传时间： 2014-01-24
上传用户：wanqunsheng
视频质料 在matlab环境中如何使用radiobutton，switch语句，边缘检测
标签： radiobutton matlab 视频 环境
上传时间： 2017-08-15
上传用户：thesk123
