SCATTERING, RADIATION AND PROPAGATION OVER TWO-DIMENSIONAL RANDOM surface,小仓老师关于随机泛函博散射的专著，除在日本京都大学作为教科书资料外，此文章作为一个章节撰写在1996年的PIER(电磁研究进展)14的第三章。
标签： TWO-DIMENSIONAL PROPAGATION SCATTERING RADIATION
上传时间： 2013-12-20
上传用户：pompey
是英文 “ surface mount technology ”的缩写。即表面安装技术，这是一种较传统的安装方式。其优点是可靠性高，缺点是体积大，成本高，限制 LCM 的小型化。 是英文 “ Chip On Board ”的缩写。即芯片被邦定(Bonding)在PCB上，由于IC制造商在LCD控制及相关芯片的生产上正在减小QFP（ SMT 的一种）封装的产量，因此，在今后的产品中传统的 SMT 方式将被逐步取代。
标签： technology surface mount 英文
上传时间： 2016-10-08
上传用户：nairui21
In this program we calculate the scattering field of a infinite rectangular surface. I use Physical Optic method and compare the result with exact solution.
标签： rectangular scattering calculate Physical
上传时间： 2014-01-19
上传用户：362279997
Bezier surface in c. Without compiler. This is very good - I think.
标签： c. compiler surface Without
上传时间： 2017-09-08
上传用户：litianchu
This reference design (RD) features a fullyassembled and tested surface-mount printed circuitboard (PCB). The RD board utilizes the MAX48851:2 or 2:1 multiplexer and other ICs to implement acomplete video graphics array (VGA) 8:1multiplexer.VGA input/output connections are provided to easilyinterface the MAX4885 RD board with VGAcompatibledevices. The RD board gives the optionto use a single 5V DC power supply (V+), or this RDboard can be powered from any one of the eight VGA sources.
标签： multiplexer reference VGA
上传时间： 2013-11-09
上传用户：ANRAN
【摘要】本文结合作者多年的印制板设计经验，着重印制板的电气性能，从印制板稳定性、可靠性方面，来讨论多层印制板设计的基本要求。【关键词】印制电路板；表面贴装器件；高密度互连；通孔【Key words】Printed Circuit Board；surface Mounting Device；High Density Interface；Via一．概述印制板（PCB－Printed Circuit Board）也叫印制电路板、印刷电路板。多层印制板，就是指两层以上的印制板，它是由几层绝缘基板上的连接导线和装配焊接电子元件用的焊盘组成，既具有导通各层线路，又具有相互间绝缘的作用。随着SMT（表面安装技术）的不断发展，以及新一代SMD（表面安装器件）的不断推出，如QFP、QFN、CSP、BGA（特别是MBGA），使电子产品更加智能化、小型化，因而推动了PCB工业技术的重大改革和进步。自1991年IBM公司首先成功开发出高密度多层板（SLC）以来，各国各大集团也相继开发出各种各样的高密度互连（HDI）微孔板。这些加工技术的迅猛发展，促使了PCB的设计已逐渐向多层、高密度布线的方向发展。多层印制板以其设计灵活、稳定可靠的电气性能和优越的经济性能，现已广泛应用于电子产品的生产制造中。下面，作者以多年设计印制板的经验，着重印制板的电气性能，结合工艺要求，从印制板稳定性、可靠性方面，来谈谈多层制板设计的基本要领。
上传时间： 2013-11-19
上传用户：zczc
Calculation of the Differential Impedance of Tracks on FR4 substrates There is a discrepancy between calculated and measured values of impedance for differential transmission lineson FR4. This is especially noticeable in the case of surface microstrip configurations. The anomaly is shown tobe due to the nature of the substrate material. This needs to be considered as a layered structure of epoxy resinand glass fibre. Calculations, using Boundary Element field methods, show that the distribution of the electricfield within this layered structure determines the apparent dielectric constant and therefore affects theimpedance. Thus FR4 cannot be considered to be uniform dielectric when calculating differential impedance.
上传时间： 2014-12-24
上传用户：DE2542
In a recent discussion with a system designer, the requirementfor his power supply was to regulate 1.5Vand deliver up to 40A of current to a load that consistedof four FPGAs. This is up to 60W of power that must bedelivered in a small area with the lowest height profi lepossible to allow a steady fl ow of air for cooling. Thepower supply had to be surface mountable and operateat high enough effi ciency to minimize heat dissipation.He also demanded the simplest possible solution so histime could be dedicated to the more complex tasks. Asidefrom precise electrical performance, this solution had toremovethe heat generated during DC to DC conversionquickly so that the circuit and the ICs in the vicinity do notoverheat. Such a solution requires an innovative designto meet these criteria:
上传时间： 2013-11-24
上传用户：defghi010
The LTM4601 DC/DC μModule regulator is a completehigh power density stepdown regulator for up to 12Acontinuous (14A peak) loads. The device is housed ina small 15mm ¥ 15mm ¥ 2.8mm LGA surface mountpackage, thus the large power dissipation is a challengein some applications. This thermal application note willprovide guidelines for using the μModule regulator inambient environments with or without air fl ow. Loadcurrent derating curves are provided for several inputvoltages and output voltages versus ambient temperatureand air fl ow.
上传时间： 2013-10-19
上传用户：bakdesec
The LTM4600 DC/DC μModule regulator is a complete highpower density stepdown regulator for 10A continuous (14Apeak) loads. The device has two voltage options: 20VINmaximum for the LTM4600EV and 28VIN maximum for theLTM4600HVEV each housed in a small 15mm ¥ 15mm ¥2.8mm LGA surface mount package.
上传时间： 2013-10-10
上传用户：adada
