solves the incompressible Navier-Stokes equations in a rectangular domain with prescribed velocities along the boundary. The standard setup solves a lid driven cavity problem.
标签： incompressible Navier-Stokes rectangular prescribed
上传时间： 2013-11-25
上传用户：15736969615
this program solves the steady-state navier-stokes eqn in 2d for the flow in a driven cavity problem. the function solved for is the streamfunction. the velocity may be obtained by differentiating the streamfunction.
标签： navier-stokes steady-state the program
上传时间： 2014-01-06
上传用户：himbly
the program is used to find out the FFT using time in decimation and solves problem of dsp fft ,compared with inbuilt fft and goertzel function , working well given with output also.
标签： decimation the program problem
上传时间： 2014-01-04
上传用户：wsf950131
This project solves the purpose of creating vb6 application using oracle database in back end. It shows how to handle the record with the oracle. my other source codes are at: http://www.developerssourcecode.com Shyam Singh Chandel
标签： application creating database project
上传时间： 2013-12-18
上传用户：清风冷雨
load flow algorithm, with entering bus data and line data it solves the load flow with newton method.
上传时间： 2014-01-22
上传用户：aix008
library for SVMclassification and regression. It solves C-SVM classification, nu-SVM classification, one-class-SVM, epsilon-SVM regression, and nu-SVM regression. It also provides an automatic model selection tool for C-SVM classification.
标签： classification SVMclassification regression library
上传时间： 2013-12-21
上传用户：thuyenvinh
Abstract: A resistive feedback network is often used to set the output voltage of a power supply. A mechanical potentiometer (pot)conveniently solves the problem of adjusting a power supply. For easier automatic calibration, a mechanical pot can be replaced witha digital pot. This application note presents a calibration solution that uses a digital pot, because digipots are smaller, do not movewith age or vibration, and can be recalibrated remotely. This proposed solution reduces the susceptibility of the system to thetolerance of the digital pot's end-to-end resistance, making the solution optimal fordesigners. This application note also explainssome of the equations required to calculate the resistor chain values and to use a digital pot in this way. A spreadsheet withstandard reisistor values is available for easy calculations.
上传时间： 2013-10-31
上传用户：caiguoqing
Piezoelectric motors are used in digital cameras for autofocus,zooming and optical image stabilization. Theyare relatively small, lightweight and effi cient, but theyalso require a complicated driving scheme. Traditionally,this challenge has been met with the use ofseparatecircuits, including a step-up converter and an oversizedgeneric full-bridge drive IC. The resulting high componentcount and large board space are especially problematicin the design of cameras for ever shrinking cell phones.The LT®3572 solves these problems by combining astep-up regulator and a dual full-bridge driver in a 4mm× 4mm QFN package. Figure 1 shows a typical LT3572Piezo motor drive circuit. A step-up converter is usedto generate 30V from a low voltage power source suchas a Li-Ion battery or any input power source within thepart’s wide input voltage range of 2.7V to 10V. The highoutput voltage of the step-up converter, adjustable upto 40V, is available for the drivers at the VOUT pin. Thedrivers operate in a full-bridge fashion, where the OUTAand OUTB pins are the same polarity as the PWMA andPWMB pins, respectively, and the OUTA and OUTB pinsare inverted from PWMA and PWMB, respectively. Thestep-up converter and both Piezo drivers have their ownshutdown control. Figure 2 shows a typical layout
上传时间： 2013-11-18
上传用户：hulee
As environmental concerns over traditional lighting increaseand the price of LEDs decreases, high power LEDsare fast becoming a popular lighting solution for offl ineapplications. In order to meet the requirements of offl inelighting—such as high power factor, high effi ciency, isolationand TRIAC dimmer compatibility—prior LED driversused many external discrete components, resulting incumbersome solutions. The LT®3799 solves complexity,space and performance problems by integrating all therequired functions for offl ine LED lighting.
上传时间： 2013-10-13
上传用户：dongqiangqiang
提出一种基于凌阳单片机的步进电机加减速的控制方法。采用凌阳科技推出的16位结构工控单片机SPMC75F2413A为控制器，由Allegro公司生产的两相步进电机专用驱动器件SLA7042M构成步进电机的驱动电路，在传统的3段直线加减速控制算法基础上增加至7段S形曲线加减速过程，控制步进电机的启动和停止。实验结果表明，该控制方法克服了直线加减速中不连续、易造成系统冲击的问题，整个系统实现柔性控制，电机启动、停止连续性能提高30%。 Abstract: The method of controlled stepping motor is referred based on SPMC75F2413A MCU， which adopts the 16 knots SPMC75F2413A MCU as the controller. The special-purpose actuation chip SLA7042M of two stepping motor produced by Allegro Corporation constituted to actuation electric circuit. The purpose of increasing to seven section of S shape curve based on the traditional three sections of straight line is to control the start and stop process of stepping motor. The experimental results show that the control method solves easy to pull-out and overshot problems. The overall system realizes flexible control， and the performance of motor start or stop continuity is increased 30%
上传时间： 2013-12-08
上传用户：jiangfire
