在半导体制冷技术的工作性能及其优缺点研究的基础上,设计了以单片机为核心控制元件,以TEC1-12706为执行元件的半导体制冷温度控制系统。采用高精度分段式PID控制算法配合PWM输出控制的方法实现温度控制;选择数字传感器DS18B20为温度检测元件,还包含1602液晶显示模块、按键调整输入模块和H桥驱动模块等。实际测试表明,该系统结构简单易行,操作方便,工作性能优良,同时针对该系统专门设计的温控算法,使半导体制冷器能更好地适应不同工况而充分发挥其制冷制热工作特性。Based on the study of the performance and advantages and disadvantages of thermoelectric cooler(TEC)technology,a thermoelectric cooling temperature control system with single-chip microcomputer as the core control element and TEC1-12706 as the executive element was designed. High precision piecewise PID control algorithm combined with PWM output control method is adopted to realize temperature control. The digital sensor DS18B20 is selected as the temperature detection element. It also includes 1602 LCD module,key adjustment input module and H bridge drive module. The actual test shows that the system has simple structure,convenient operation and excellent performance. Meanwhile,the temperature control algorithm specially designed for the system can make the semiconductor cooler better adapt to different working conditions and give full play to its refrigeration and heating characteristics.
上传时间： 2022-03-27
上传用户：
数字示波器功能强大,使用方便,但是价格相对昂贵。本文以Ti的MSP430F5529为主控器,以Altera公司的EP2C5T144C8 FPGA器件为逻辑控制部件设计数字示波器。模拟信号经程控放大、整形电路后形成方波信号送至FPGA测频,根据频率值选择采用片上及片外高速AD分段采样。FPGA控制片外AD采样并将数据输入到FIFO模块中缓存,由单片机进行频谱分析。测试表明:简易示波器可以实现自动选档、多采样率采样、高精度测频及频谱分析等功能。Digital oscilloscope is powerful and easy to use, but also expensive. The research group designed a low-cost digital oscilloscope, the chip of MSP430F5529 of TI is chosen as the main controller and the device of EP2C5T144C8 of Altera company is used as the logic control unit. Analog signal enter the programmable amplifier circuit, shaping circuit and other pre-processing circuit. The shaped rectangular wave signal is sent to FPGA for measure the frequency. According to the frequency value to select AD on-chip or off-chip high-speed AD for sampling. FPGA controls the off-chip AD sampling and buffers AD data by FIFO module. The single chip microcomputer receives the data, and do FFT for spectrum analysis. The test shows that the simple oscilloscope can realize automatic gain selection, sampling at different sampling rates, high precision frequency measurement and spectrum analysis.
上传时间： 2022-03-27
上传用户：
在传统智能小车驱动电路设计中,较多考虑使用直流电机还是步进电机,电机功率、能耗等性能参数。使用具有armCortexM4内核的STM32嵌入式平台控制四轮的4个直流电机。文章基于PWM技术及PID算法,对四轮进行精准地速度、转向及启停控制,实验表明此小车具有优越各种地形适应能力。In the traditional intelligent car drive circuit design,DC motor or stepping motor,motor power,energy consumption and other performance parameters are considered.The four DC motors with four wheels are controlled by STM32 embedded platform with arm Cortex M4 kernel.Based on the PWM technology and PID algorithm,the accurate ground speed,steering,and start-stop control of the four wheels are carried out.The experiment shows that the vehicle has the superior adaptability to all kinds of terrains.
上传时间： 2022-04-02
上传用户：
This example shows how you can use signal functions in the Visiondebugger to simulate a signal that is coming into one of the analog inputs of the LPC21xx.The Measure example is described in detail in the Getting StartedUser's Guide.The MEASURE example program is available for several targets:Simulator: uVision Simulator for LPC2129MCB2100: Keil MCB2100 evaluation board with ULINK debugger - Application is loaded to internal Flash. - Switch S2 (INT1) is used as GPIO and sampled (jumper positions: J1= off, J7= on) - potentiometer POT1 is sampled as AIN0 (jumper position: J2= on) - serial port COM1 parameters: 9600 baud, no parity, 8-bits, 1 stop bit, flow control noneMCB2130: Keil MCB2130 evaluation board with ULINK debugger - Application is loaded to internal Flash. - Switch S2 (INT1) is used as GPIO and sampled (jumper positions: J1= off, J7= on) - potentiometer POT1 is sampled as AIN1 (jumper position: J2= on) - serial port COM1 parameters: 9600 baud, no parity, 8-bits, 1 stop bit, flow control none
标签： dac8568
上传时间： 2022-06-28
上传用户：
