The CAT93C46 is a 1 kb Serial EEPROM memory device which isconfigured as either 64 registers of 16 bits (ORG pin at VCC) or 128registers of 8 bits (ORG pin at GND). Each register can be written (orread) serially by using the DI (or DO) pin. The CAT93C46 features aself−timed internal write with auto−clear. On−chip Power−On Resetcircuit protects the internal logic against powering up in the wrongstate.
上传时间： 2013-11-19
上传用户：ynzfm
The SN65LBC170 and SN75LBC170 aremonolithic integrated circuits designed forbidirectional data communication on multipointbus-transmission lines. Potential applicationsinclude serial or parallel data transmission, cabledperipheral buses with twin axial, ribbon, ortwisted-pair cabling. These devices are suitablefor FAST-20 SCSI and can transmit or receivedata pulses as short as 25 ns, with skew lessthan 3 ns.These devices combine three 3-state differentialline drivers and three differential input linereceivers, all of which operate from a single 5-Vpower supply.The driver differential outputs and the receiverdifferential inputs are connected internally to formthree differential input/output (I/O) bus ports thatare designed to offer minimum loading to the buswhenever the driver is disabled or VCC = 0. Theseports feature a wide common-mode voltage rangemaking the device suitable for party-lineapplications over long cable runs.
上传时间： 2013-10-13
上传用户：ytulpx
NXP Semiconductor designed the LPC2400 microcontrollers around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded Trace. The LPC2400 microcontrollers have 512 kB of on-chip high-speedFlash memory. This Flash memory includes a special 128-bit wide memory interface andaccelerator architecture that enables the CPU to execute sequential instructions fromFlash memory at the maximum 72 MHz system clock rate. This feature is available onlyon the LPC2000 ARM Microcontroller family of products. The LPC2400 can execute both32-bit ARM and 16-bit Thumb instructions. Support for the two Instruction Sets meansEngineers can choose to optimize their application for either performance or code size atthe sub-routine level. When the core executes instructions in Thumb state it can reducecode size by more than 30 % with only a small loss in performance while executinginstructions in ARM state maximizes core performance.
上传时间： 2013-11-14
上传用户：zouxinwang
The PCA9544A provides 4 interrupt inputs, one for each channeland one open drain interrupt output. When an interrupt is generated byany device, it will be detected by the PCA9544A and the interruptoutput will be driven LOW. The channel need not be active fordetection of the interrupt. A bit is also set in the control byte.Bits 4 – 7 of the control byte correspond to channels 0 – 3 of thePCA9544A, respectively. Therefore, if an interrupt is generated byany device connected to channel 2, the state of the interrupt inputs isloaded into the control register when a read is accomplished.Likewise, an interrupt on any device connected to channel 0 wouldcause bit 4 of the control register to be set on the read. The mastercan then address the PCA9544A and read the contents of thecontrol byte to determine which channel contains the devicegenerating the interrupt. The master can then reconfigure thePCA9544A to select this channel, and locate the device generatingthe interrupt and clear it. The interrupt clears when the deviceoriginating the interrupt clears.
标签： 4channel multiple 9544A 9544
上传时间： 2014-12-27
上传用户：潜水的三贡
The PCA9549 provides eight bits of high speed TTL-compatible bus switching controlledby the I2C-bus. The low ON-state resistance of the switch allows connections to be madewith minimal propagation delay. Any individual A to B channel or combination of channelscan be selected via the I2C-bus, determined by the contents of the programmable Controlregister. When the I2C-bus bit is HIGH (logic 1), the switch is on and data can flow fromPort A to Port B, or vice versa. When the I2C-bus bit is LOW (logic 0), the switch is open,creating a high-impedance state between the two ports, which stops the data flow.An active LOW reset input (RESET) allows the PCA9549 to recover from a situationwhere the I2C-bus is stuck in a LOW state. Pulling the RESET pin LOW resets the I2C-busstate machine and causes all the bits to be open, as does the internal power-on resetfunction.
上传时间： 2014-11-22
上传用户：xcy122677
The PCA9548A is an octal bidirectional translating switch controlled via the I2C-bus. TheSCL/SDA upstream pair fans out to eight downstream pairs, or channels. Any individualSCx/SDx channel or combination of channels can be selected, determined by thecontents of the programmable control register.An active LOW reset input allows the PCA9548A to recover from a situation where one ofthe downstream I2C-buses is stuck in a LOW state. Pulling the RESET pin LOW resets theI2C-bus state machine and causes all the channels to be deselected as does the internalPower-on reset function.
上传时间： 2013-10-13
上传用户：bakdesec
The PCA9557 is a silicon CMOS circuit which provides parallel input/output expansion for SMBus and I2C-bus applications. The PCA9557 consists of an 8-bit input port register, 8-bit output port register, and an I2C-bus/SMBus interface. It has low current consumption and a high-impedance open-drain output pin, IO0. The system master can enable the PCA9557’s I/O as either input or output by writing to the configuration register. The system master can also invert the PCA9557 inputs by writing to the active HIGH polarity inversion register. Finally, the system master can reset the PCA9557 in the event of a time-out by asserting a LOW in the reset input. The power-on reset puts the registers in their default state and initializes the I2C-bus/SMBus state machine. The RESET pin causes the same reset/initialization to occur without de-powering the part.
上传时间： 2014-01-18
上传用户：bs2005
设计一种应用于某全地形ATV车载武器装置中的中控系统，该系统设计是以TMS320F2812型DSP为核心，采用模块化设计思想，对其硬件部分进行系统设计，能够完成对武器装置高低、回转方向的运动控制，实现静止或行进状态中对目标物的测距，自动瞄准以及按既定发射模式发射弹丸和各项安全性能检测等功能。通过编制相应的软件，对其进行系统调试，验证了该设计运行稳定。 Abstract: A central control system applied to an ATV vehicle weapons is designed. The system design is based on TMS320F2812 DSP as the core， uses modular design for its hardware parts. The central control system can complete the motion control of the level of weapons and equipment， rotation direction， to achieve a state of static or moving objects on the target ranging， auto-targeting and according to the established target and the projectile and the launch of the security performance testing and other functions. Through the development of appropriate software and to carry out system testing to verify the stability of this design and operation.
上传时间： 2013-11-02
上传用户：jshailingzzh
The #1 Step-by-Step Guide to labviewNow Completely Updated for labview 8! Master labview 8 with the industry's friendliest, most intuitive tutorial: labview for Everyone, Third Edition. Top labview experts Jeffrey Travis and Jim Kring teach labview the easy way: through carefully explained, step-by-step examples that give you reusable code for your own projects! This brand-new Third Edition has been fully revamped and expanded to reflect new features and techniques introduced in labview 8. You'll find two new chapters, plus dozens of new topics, including Project Explorer, AutoTool, XML, event-driven programming, error handling, regular expressions, polymorphic VIs, timed structures, advanced reporting, and much more. Certified labview Developer (CLD) candidates will find callouts linking to key objectives on NI's newest exam, making this book a more valuable study tool than ever. Not just what to d why to do it! Use labview to build your own virtual workbench Master labview's foundations: wiring, creating, editing, and debugging VIs; using controls and indicators; working with data structures; and much more Learn the "art" and best practices of effective labview development NEW: Streamline development with labview Express VIs NEW: Acquire data with NI-DAQmx and the labview DAQmx VIs NEW: Discover design patterns for error handling, control structures, state machines, queued messaging, and more NEW: Create sophisticated user interfaces with tree and tab controls, drag and drop, subpanels, and more Whatever your application, whatever your role, whether you've used labview or not, labview for Everyone, Third Edition is the fastest, easiest way to get the results you're after!
上传时间： 2013-10-14
上传用户：shawvi
6小时学会labview, labview Six Hour Course – Instructor Notes This zip file contains material designed to give students a working knowledge of labview in a 6 hour timeframe. The contents are: Instructor Notes.doc – this document. labviewIntroduction-SixHour.ppt – a PowerPoint presentation containing screenshots and notes on the topics covered by the course. Convert C to F (Ex1).vi – Exercise 1 solution VI. Convert C to F (Ex2).vi – Exercise 2 solution subVI. Thermometer-DAQ (Ex2).vi – Exercise 2 solution VI. Temperature Monitor (Ex3).vi – Exercise 3 solution VI. Thermometer (Ex4).vi – Exercise 4 solution subVI. Convert C to F (Ex4).vi – Exercise 4 solution subVI. Temperature Logger (Ex4).vi – Exercise 4 solution VI. Multiplot Graph (Ex5).vi – Exercise 5 solution VI. Square Root (Ex6).vi – Exercise 6 solution VI. State Machine 1 (Ex7).vi – Exercise 7 solution VI. The slides can be presented in two three hour labs, or six one hour lectures. Depending on the time and resources available in class, you can choose whether to assign the exercises as homework or to be done in class. If you decide to assign the exercises in class, it is best to assign them in order with the presentation. This way the students can create VI’s while the relevant information is still fresh. The notes associated with the exercise slide should be sufficient to guide the students to a solution. The solution files included are one possible solution, but by no means the only solution.
标签： labview
上传时间： 2013-10-12
上传用户：zjwangyichao
