PCI总线是目前最为流行的一种局部性总线 通过对PCI总线一些典型功能的分析以及时序的阐述，利用VetilogHDL设计了一个将非PCI功能设备转接到PC1总线上的IP Core 同时，通过在ModeISim SE PLUS 6．0 上运行测试程序模块，得到了理想的仿真数据波形，从软件上证明了功能的实现。
上传时间： 2014-12-30
上传用户：himbly
The PCI Special Interest Group disclaims all warranties and liability for the use of this document and the information contained herein and assumes no responsibility for any errors that may appear in this document, nor does the PCI Special Interest Group make a commitment to update the information contained herein.
上传时间： 2013-11-01
上传用户：KSLYZ
作为一种独立于处理器的局部总线,PCI非常适用于网络适配器、硬盘驱动器、全动态视频卡、图形卡及各类高速外设。据称,目前有90%的Pentium处理器采用PCI做为系统总线。
上传时间： 2013-11-06
上传用户：liaocs77
PCI Express是由Intel，Dell，Compaq，IBM，Microsoft等PCI SIG联合成立的Arapahoe Work Group共同草拟并推举成取代PCI总线标准的下一代标准。PCI Express利用串行的连接特点能轻松将数据传输速度提到一个很高的频率，达到远远超出PCI总线的传输速率。一个PCI Express连接可以被配置成x1，x2，x4，x8，x12，x16和x32的数据带宽。x1的通道能实现单向312.5 MB／s（2.5 Gb／s）的传输速率。Xilinx公司的Virtex5系列FPGA芯片内嵌PCI-ExpressEndpoint Block硬核，为实现单片可配置PCI-Express总线解决方案提供了可能。 本文在研究PCI-Express接口协议和PCI-Express Endpoint Block硬核的基础上，使用Virtex5LXT50 FPGA芯片设计PCI Express接口硬件电路，实现PCI-Express数据传输
上传时间： 2013-12-26
上传用户：wtrl
The Virtex-4 features, such as the programmable IDELAY and built-in FIFO support, simplifythe bridging of a high-speed, PCI-X core to large amounts of DDR-SDRAM memory. Onechallenge is meeting the PCI-X target initial latency specification. PCI-X Protocol Addendum tothe PCI Local Bus Specification Revision 2.0a ([Ref 6]) dictates that when a target signals adata transfer, "the target must do so within 16 clocks of the assertion of FRAME#." PCItermination transactions, such as Split Response/Complete, are commonly used to meet thelatency specifications. This method adds complexity to the design, as well as additional systemlatency. Another solution is to increase the ratio of the memory frequency to the PCI-X busfrequency. However, this solution increases the required power and clock resource usage.
上传时间： 2013-11-24
上传用户：18707733937
PCI-PCI 桥启动时，一般需要从EEPROM 预读取配置数据。更改EEPROM中的数据一般需要专用的烧结器，这给调试过程带来不便。尤其是采用表贴封装的EEPROM。本文以Intel 公司的Dec21554PCI-PCI 桥为例，介绍一种在线读写EEPROM 的方法。EEPROM选用的是ATMEL 公司生产的AT93LC66，4Kbit，按512×8bit 组织。
上传时间： 2013-11-08
上传用户：trepb001
The LogiCORE™ GTP Wizard automates the task of creating HDL wrappers to configure the high-speed serial GTP transceivers in Virtex™-5 LXT and SXT devices. The menu-driven interface allows one or more GTP transceivers to be configured using pre-definedtemplates for popular industry standards, or from scratch, to support a wide variety of custom protocols.The Wizard produces a wrapper, an example design, and a testbench for rapid integration and verification of the serial interface with your custom function Features• Creates customized HDL wrappers to configureVirtex-5 RocketIO™ GTP transceivers• Users can configure Virtex-5 GTP transceivers toconform to industry standard protocols usingpredefined templates, or tailor the templates forcustom protocols• Included protocol templates provide support for thefollowing specifications: Aurora, CPRI, FibreChannel 1x, Gigabit Ethernet, HD-SDI, OBSAI,OC3, OC12, OC48, PCI Express® (PCIe®), SATA,SATA II, and XAUI• Automatically configures analog settings• Each custom wrapper includes example design, testbench; and both implementation and simulation scripts
标签： Transceiver Virtex Wizar GTP
上传时间： 2013-10-20
上传用户：dave520l
This document provides practical, common guidelines for incorporating PCI Express interconnect layouts onto Printed Circuit Boards (PCB) ranging from 4-layer desktop baseboard designs to 10- layer or more server baseboard designs. Guidelines and constraints in this document are intended for use on both baseboard and add-in card PCB designs. This includes interconnects between PCI Express devices located on the same baseboard (chip-to-chip routing) and interconnects between a PCI Express device located “down” on the baseboard and a device located “up” on an add-in card attached through a connector. This document is intended to cover all major components of the physical interconnect including design guidelines for the PCB traces, vias and AC coupling capacitors, as well as add-in card edge-finger and connector considerations. The intent of the guidelines and examples is to help ensure that good high-speed signal design practices are used and that the timing/jitter and loss/attenuation budgets can also be met from end-to-end across the PCI Express interconnect. However, while general physical guidelines and suggestions are given, they may not necessarily guarantee adequate performance of the interconnect for all layouts and implementations. Therefore, designers should consider modeling and simulation of the interconnect in order to ensure compliance to all applicable specifications. The document is composed of two main sections. The first section provides an overview of general topology and interconnect guidelines. The second section concentrates on physical layout constraints where bulleted items at the beginning of a topic highlight important constraints, while the narrative that follows offers additional insight.
上传时间： 2014-01-23
上传用户：s363994250
PCI-E是一种高速传输总线形式。
上传时间： 2013-12-18
上传用户：宋桃子
PCI-1734快速安装使用手册PCI-1734快速安装使用手册PCI-1734快速安装使用手册PCI-1734快速安装使用手册PCI-1734快速安装使用手册PCI-1734快速安装使用手册PCI-1734快速安装使用手册
上传时间： 2013-10-21
上传用户：ssz1990
