The LPC1700 Ethernet block contains a full featured 10 Mbps or 100 Mbps Ethernet MAC (Media Access Controller) designed to provide optimized performance through the use of DMA hardware acceleration. Features include a generous suite of control registers, half or full duplex operation, flow control, control frames, hardware acceleration for transmit retry, receive packet filtering and wake-up on LAN activity. Automatic frame transmission and reception with Scatter-Gather DMA off-loads many operations from the CPU.
上传时间： 2013-11-09
上传用户：geshaowei
The PCA9541 is a 2-to-1 I2C-bus master selector designed for high reliability dual masterI2C-bus applications where system operation is required, even when one master fails orthe controller card is removed for maintenance. The two masters (for example, primaryand back-up) are located on separate I2C-buses that connect to the same downstreamI2C-bus slave devices. I2C-bus commands are sent by either I2C-bus master and are usedto select one master at a time. Either master at any time can gain control of the slavedevices if the other master is disabled or removed from the system. The failed master isisolated from the system and will not affect communication between the on-line masterand the slave devices on the downstream I2C-bus.
上传时间： 2013-10-09
上传用户：3294322651
The PCA9555 is a 24-pin CMOS device that provides 16 bits of General Purpose parallelInput/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed toenhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvementsinclude higher drive capability, 5 V I/O tolerance, lower supply current, individual I/Oconfiguration, and smaller packaging. I/O expanders provide a simple solution whenadditional I/O is needed for ACPI power switches, sensors, push buttons, LEDs, fans, etc.The PCA9555 consists of two 8-bit Configuration (Input or Output selection); Input, Outputand Polarity Inversion (active HIGH or active LOW operation) registers. The systemmaster can enable the I/Os as either inputs or outputs by writing to the I/O configurationbits. The data for each Input or Output is kept in the corresponding Input or Outputregister. The polarity of the read register can be inverted with the Polarity Inversionregister. All registers can be read by the system master. Although pin-to-pin and I2C-busaddress compatible with the PCF8575, software changes are required due to theenhancements, and are discussed in Application Note AN469.
上传时间： 2013-11-13
上传用户：fredguo
The TL2575 and TL2575HV represent superior alternatives to popular three-terminal linear regulators. Due totheir high efficiency, the devices significantly reduce the size of the heatsink and, in many cases, no heatsink isrequired. Optimized for use with standard series of inductors available from several different manufacturers, theTL2575 and TL2575HV greatly simplify the design of switch-mode power supplies by requiring a minimaladdition of only four to six external components for operation.
标签： STEP-DOWN SWITCHING SIMPLE 1A
上传时间： 2013-11-20
上传用户：jelenecheung
The MAX3243E device consists of three line drivers, five line receivers, and a dual charge-pump circuit with±15-kV ESD (HBM and IEC61000-4-2, Air-Gap Discharge) and ±8-kV ESD (IEC61000-4-2, Contact Discharge)protection on serial-port connection pins. The device meets the requirements of TIA/EIA-232-F and provides theelectrical interface between an asynchronous communication controller and the serial-port connector. Thiscombination of drivers and receivers matches that needed for the typical serial port used in an IBM PC/AT, orcompatible. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-Vsupply. In addition, the device includes an always-active noninverting output (ROUT2B), which allowsapplications using the ring indicator to transmit data while the device is powered down. The device operates atdata signaling rates up to 250 kbit/s and a maximum of 30-V/ms driver output slew rate.
标签： MULTICHANNEL 5.5 TO RS
上传时间： 2013-10-19
上传用户：ddddddd
PCA9511, PCA9512, PCA9513, PCA9514, PCA9515, PCA9516, PCA9518,P82B96, P82B715Abstract - Philips Semiconductors family of Repeaters, Hubs and Expanders are detailed in this application notethat discusses device operation, maximum cable length and frequency calculations and typical applications.
上传时间： 2013-11-21
上传用户：wlcaption
The C500 microcontroller family usually provides only one on-chip synchronous serialchannel (SSC). If a second SSC is required, an emulation of the missing interface mayhelp to avoid an external hardware solution with additional electronic components.The solution presented in this paper and in the attached source files emulates the mostimportant SSC functions by using optimized SW routines with a performance up to 25KBaud in Slave Mode with half duplex transmission and an overhead less than 60% atSAB C513 with 12 MHz. Due to the implementation in C this performance is not the limitof the chip. A pure implementation in assembler will result in a strong reduction of theCPU load and therefore increase the maximum speed of the interface. In addition,microcontrollers like the SAB C505 will speed up the interface by a factor of two becauseof an optimized architecture compared with the SAB C513.Moreover, this solution lays stress on using as few on-chip hardware resources aspossible. A more excessive consumption of those resources will result in a highermaximum speed of the emulated interface.Due to the restricted performance of an 8 bit microcontroller a pin compatible solution isprovided only; the internal register based programming interface is replaced by a set ofsubroutine calls.The attached source files also contain a test shell, which demonstrates how to exchangeinformation between an on-chip HW-SSC and the emulated SW-SSC via 5 external wiresin different operation modes. It is based on the SAB C513 (Siemens 8 bit microcontroller).A table with load measurements is presented to give an indication for the fraction of CPUperformance required by software for emulating the SSC.
标签： synchronous Emulating serial
上传时间： 2014-01-31
上传用户：z1191176801
Presents short and simple I2C software routines that support onlyslave (rather than master or master & slave) operation and an ASMdemonstration program. The slave-only software in this app notecomplements the master mode software presented in AN464, Usingthe 87LPC76X microcontroller as an I2C bus master.
上传时间： 2013-11-22
上传用户：1039312764
计算机应用中，有时需处理的信息不是数字量，而是一些随时间连续变化的模拟量，甚至是一些非电量，如温度、压力、速度等。模拟量的存储处理困难。首先将非电的模拟信号变成与之对应的模拟电信号，这要通过各种传感器来完成。计算机可处理的信息均是数字量（电脉冲信号）1和0，必须把要处理的模拟电量转换成数字化的电信号，这需要模拟(Analog)与数字(Digital)转换电路。数字到模拟转换:(Digital to Analog Convert, D/A) D/A转换电路是模拟电路加上电子开关。D/A转换电路的核心是一个运算放大器。运算放大器的特性:(Operation Amplifier) K->无穷大， V和->0 传递函数：V0 = -Vi * R0/Ri Ii->0, I和=If梯形R-2R电阻网络D/A转换器Ki受一个8位二进制代码控制 某位为1，对应开关K倒向右边； 某位为0，对应开关K倒向左边。Ki不论倒向哪边，均为接地VA-VH 的电位为： VREF，1/2VREF，..1/128VREFVO= -VREF *（1/2K7+1/4K6+…+1/256K0）V0= -（0-255/256）VREF 8位D/A转换器DAC0830系列器件国家半导体公司（NS)产品，0830、0831、0832。R-2R梯形电阻网络D/A转换器，双缓冲结构。单电源、低功耗、电流建立时间1uS。与微计算机接口方便。8位D/A转换器DAC0830系列器件ILE： 输入锁存允许； WR1#： 加载IN REG； WR2#: 加载DAC REG； XFER#: IN REG传到DAC REG； Iout1,Iout2: 外接OA输入； Rfb: 反馈电阻接OA输出； VREF： 参考电源，控制输出电压变化范围。
标签： AD转换
上传时间： 2013-10-16
上传用户：lu2767
基于USB接口的数据采集模块的设计与实现Design and Implementation of USB-Based Data Acquisition Module路 永 伸(天津科技大学电子信息与自动化学院，天津300222)摘要文中给出基于USB接口的数据采集模块的设计与实现。硬件设计采用以Adpc831与PDIUSBDI2为主的器件进行硬件设计，采用Windriver开发USB驱动，并用Visual C十十6.0对主机软件中硬件接口操作部分进行动态链接库封装。关键词USB 数据采集Adpc831 PDNSBDI2 Windriver动态链接库Abstract T hed esigna ndim plementaitono fU SB-BasedD ataA cquisiitonM oduleis g iven.Th ec hips oluitonm ainlyw ithA dpc831a ndP DTUSBD12i sused for hardware design. The USB drive is developed场Wmdriver, and the operation on the hardware interface is packaged into Dynamic Link Libraries场Visual C++6.0. Keywords USB DataA cquisition Adttc831 PDfUSBD12 Windriver0 引言US B总 线 是新一代接口总线，最初推出的目的是为了统一取代PC机的各类外设接口，迄今经历了1.0,1.1与2.0版本3个标准。在国内基于USB总线的相关设计与开发也得到了快速的发展，很多设计者从各自的应用领域，用不同方案设计出了相应的装置[1,2]。数据采集是工业控制中一个普遍而重要的环节，因此开发基于USB接口的数据采集模块具有很强的现实应用意义。虽然 US B总线标准已经发展到2.0版本，但由于工业控制现场干扰信号的情况比较复杂，高速数据传输的可靠性不容易被保证，并且很多场合对数据采集的实时性要求并不高，开发2.0标准产品的成本又较1.1标准产品高，所以笔者认为，在工业控制领域，目前开发基于USB总线1.1标准实现的数据采集模块的实用意义大于相应2.0标准模块。
上传时间： 2013-10-23
上传用户：q3290766
