介绍一种基于C8051单片机的动态心电监护系统。该系统由两部分组成：以C8051F320单片机为核心的数据采集装置和以PC机为平台的分析处理系统。硬件电路功耗低，由单片机自带的USB接口将数据传送给PC机。软件平台采用LabVIEW可视化虚拟仪器系统开发平台，将传统仪器的功能模块集成到计算机中，用户可通过修改虚拟仪器的程序改变其功能。采用USB接口实时传输心电数据，并将数据采集模块设计为计算机外设，使该系统高速快捷、小巧便携。 Abstract: In this design，a low-cost ECG electrocardiogram monitoring system is introduced，which consists of two parts:data acquisition device based on C8051F320and PC terminal as the analysis and processing system.The system is low-power consumption，the data is transmitted to the PC terminal by USB interface of the C8051F320.By using the visible virtual instrument system developing platform LabVIEW，the traditional instruments function modules are integrated into the computer，so the user can modify virtual instrument software to change its function to meet their needs.Using USB in-terface to realize real-time ECG data transmission，in addition，ECG data acquisition module is designed as the computer peripheral，which makes the syetem high-speed and portable.
上传时间： 2013-11-13
上传用户：zhangzhenyu
提出一种基于C8051F040的炮塔方位角测试系统的设计方案，给出测试系统的各个模块软硬件设计。炮塔方位角测试系统集数据采集，数据传输和数据显示等功能于一体，实现了炮塔方位角装置的离线检测。系统软件采用C51编写，对单片机进行有效电源管理，保证了系统的稳定性，可靠性。 Abstract: This paper puts forwards a design of artillery position system based on C8051F040，describes all modules hardware and software design of measurement system.The system has the function of information collection，transmission，and display.It can measure artillery position system in offline.The system software using C51can manage the power of single chip microcomputer，guarantee the stability，reliability.
上传时间： 2014-12-27
上传用户：7891
介绍基于VHDL的微型打印机控制器的设计。论述了微型打印机的基本原理，以及实现控制器的VHDL语言设计。打印机的数据来自系统中的存储模块，根据需要控制打印。该微型打印机控制器可取代传统的微型打印机,且抗干扰性好,可靠性高，具有较强的移植性，稍加改动就可应用于不同场合。 Abstract: This paper introduced the design method of micro printer controller based on VHDL.The basic principles of microprinter is explained,as well as the realization of the controller by VHDL language.The printer data is from the system memory modules,can control printer.The design of microprinter controller has antigood and high reliability，it can replace the traditional printer.The controller has very good portability,and need little modify that can use in different situation.
上传时间： 2013-11-03
上传用户：dudu1210004
介绍一种采用单片机技术和基站器件EM4095的手持式低频RFID读卡器方案。首先对整个系统框架进行说明，然后介绍主要功能模块的设计，给出了各模块的原理图。重点描述了基站器件EM4095的性能参数和功能原理，最后描述了该系统的主程序流程图。 Abstract: In this paper,a handheld RFID reader based on MCU and EM4095 is introduced.At first，the configuration of this system is explained.Then the design of main modules and schematic documents are particularly presented.The parameters and principle of the chip EM4095 are introduced in detail. At last，the main software flow is given
上传时间： 2013-10-18
上传用户：windypsm
提出了一种基于C8051F320的列车安全巡检仪的设计方案，详细阐述了巡检仪的各个模块的硬、软件设计。巡检仪集信息采集、轴温检测、照明和记录存储等功能于一体，实现了对列车安全巡检工作有效的监督和科学管理。系统软件采用C51编写，对单片机进行有效的电源管理，保证了巡检仪的稳定性、可靠性和低功耗性。 Abstract: This paper puts forward a design of train safety inspection based on C8051F320,describes all modules hardware and software design of inspection instrument.The inspection instrument has the function of information collection, axle’s temperature detection, lighting and records storage.It can supervise and administer train safety inspection work effectively.The system software using C51 can manage the power of single chip microcomputer, and guarantee the stability, reliability and low power consumption of the inspection instrument.
上传时间： 2013-12-22
上传用户：落花无痕
基于幅移键控技术ASK（Amplitude-Shift Keying），以C8051F340单片机作为监测终端控制器，C8051F330D单片机作为探测节点控制器，采用半双工的通信方式，通过监控终端和探测节点的无线收发电路，实现数据的双向无线传输。收发电路采用直径为0.8 mm的漆包线自行绕制成圆形空心线圈天线，天线直径为（3.4±0.3）cm。试验表明，探测节点与监测终端的通信距离为24 cm，通过桥接方式，节点收发功率为102 mW时，节点间的通信距离可达20 cm。与传统无线收发模块相比，该无线收发电路在受体积、功耗、成本限制的场合有广阔的应用前景。 Abstract: Based on ASK technology and with the C8051F340 and C8051F330D MCU as the controller， using half-duplex communication mode， this paper achieves bi-directional data transfer. Transceiver circuit constituted by enameled wire which diameter is 0.8mm and wound into a diameter （3.4±0.3） cm circular hollow coil antenna. Tests show that the communication distance between detection and monitoring of the terminal is 24cm，the distance is up to 20cm between two nodes when using the manner of bridging and the node transceiver power is 102mW. Compared with the conventional wireless transceiver modules， the circuit has wide application prospect in small size， low cost and low power consumption and other characteristics.
上传时间： 2013-10-19
上传用户：xz85592677
针对船舶气象仪保障维修而设计的船舶气象仪测试系统，包括信息处理终端、主仪器检测模块、传感器检测模块，各个模块都采用基于AVR单片机的嵌入式系统，模块之间通过CAN总线进行通信。结果表明，船舶气象仪测试系统能够快速检测船舶气象仪故障，与单纯依靠人工方式排查故障相比，故障检测时间缩短了60%以上。 Abstract: The test system of ship meteorological instrument was developed to satisfy the maintenance of ship meteorological instruments，which composed of information processing terminal， testing module of main instrument and testing module of sensors. Each of these modules included an embedded system based on microcontroller of AVR series and communicated with other module by CAN bus. The results show that the test system can judge the fault of ship meteorological instrument quickly and shorten the fault detection time as much as 60% compared with simple manual troubleshooting.
上传时间： 2013-11-23
上传用户：stvnash
MPLAB C30用户指南(英文) HIGHLIGHTSThe information covered in this chapter is as follows:• About this Guide• Recommended Reading• Troubleshooting• The Microchip Web Site• Development Systems Customer Notification Service• Customer Support Document LayoutThe document layout is as follows:• Chapter 1: Compiler Overview – describes MPLAB C30, development tools andfeature set.• Chapter 2: Differences between MPLAB C30 and ANSI C – describes thedifferences between the C language supported by MPLAB C30 syntax and thestandard ANSI-89 C.• Chapter 3: Using MPLAB C30 – describes how to use the MPLAB C30 compilerfrom the command line.• Chapter 4: MPLAB C30 Runtime Environment – describes the MPLAB C30runtime model, including information on sections, initialization, memory models, thesoftware stack and much more.• Chapter 5: Data Types – describes MPLAB C30 integer, floating point and pointerdata types.• Chapter 6: Device Support Files – describes the MPLAB C30 header and registerdefinition files, as well as how to use with SFR’s.• Chapter 7: Interrupts – describes how to use interrupts.• Chapter 8: Mixing Assembly Language and C modules – provides guidelines tousing MPLAB C30 with MPLAB ASM30 assembly language modules.
上传时间： 2013-10-21
上传用户：13925096126
The Controller Area Network (CAN) is a serial, asynchronous, multi-master communication protocol forconnecting electronic control modules, sensors and actuators in automotive and industrial applications.With the SJA1000, Philips Semiconductors provides a stand-alone CAN controller which is more than a simpleeplacement of the PCA82C200.Attractive features are implemented for a wide range of applications, supporting system optimization, diagnosisand maintenance.
标签： Stand-alone contro 1000 SJA
上传时间： 2013-11-18
上传用户：yxgi5
基于LabVIEW和单片机的空调温度场测量系统的研究:室内温度是空调系统舒适性的重要指标,对其及时、准确地测量显得非常重要。介绍单片机AT89C51 和数字式、单总线型温度传感器DS18B20 组成矩形测量网络采集空调室内40 点温度,LabVIEW作为开发平台,二者之间通过串口实现数据通信,利用LabVIEW强大的数据处理和显示功能对采集的空调温度场数据进行实时处理、分析和显示,详细介绍了系统的硬件结构和软件模块的设计方案。关键词:单片机;DS18B20 ;LabVIEW;串行通信 Abstract : Temperature is a very important criterion of air condition system′s comfort , so it is very significant to measure it accurately and real timely. This paper int roduces a data acquisition system of measuring 40 point s temperature for air condition room based on single wire digital sensor DS18B20 and microcont roller AT89C51 which are composed of rectangle measuring meshwork. The data communication between LabVIEW and microcont roller is executed via serial port ,and the temperature field data of air condition room are processed analyzed and displayed on LabVIEW. The hardware and software modules are also given in detail.Keywords : single chip ;DS18B20 ;LabVIEW; serial communication
上传时间： 2014-05-05
上传用户：KSLYZ
