Abstract: The MAX9930–MAX9933 family of RF controllers and detector can be used in a wide variety of applications. Anideal application is cable television (CATV) over fiber, where either a RF controller or a RF detector controls the gain of atransimpedance amplifier (TIA). This application note shows how the MAX9930 (RF controller) can be used as either theRF controller or detector.
上传时间： 2013-10-11
上传用户：Pzj
基于数字微镜器件（Digital Micro-mirror Device，DMD）的哈达玛变换光谱技术是一种新型的光谱成像技术，在国内很少有专门的文献介绍[1-3]。文中先介绍了本实验采用的哈达玛光谱仪样机的原理以及哈达玛成像光谱仪优于传统模板的独特之处，即获得多通道高能量高信噪比的光谱数据，然后描述对采集到的数据做高信噪比，高分辨率压缩处理，最后说明此方法实时性强、图像失真小、实用价值高、应用范围广。
上传时间： 2013-11-25
上传用户：eastimage
Abstract: This document details the Oceanside (MAXREFDES9#) subsystem reference design, a 3.3V to 15V input,±15V (±12V) output, isolated power supply. The Oceanside design includes a high-efficiency step-up controller, a36V H-bridge transformer driver for isolated supplies, a wide input range, and adjustable output low-dropout linearregulator (LDO). Test results and hardware files are included.
上传时间： 2013-10-12
上传用户：jinyao
Abstract: The DS1875 features a pulse-width modulation (PWM) controller that can be used to control aDC-DC converter. The DC-DC converter can then be used to generate the high bias voltages necessaryfor avalanche photodiodes (APDs). This application note describes the operation of a boost converterthat uses the DS1875. Discussion covers the selection of the inductor and switching frequency, and theselection of components that improve the efficiency of the converter. Test data are presented.
上传时间： 2013-10-26
上传用户：lyson
Abstract: Uses the MAX641 switching controller and an external discrete charge pump to step up the input voltage. This circuitcan service low loads and is efficient when the output is two, three, four times the input voltage. Adding the MAX627 MOSdriver can further increase the output current capability.
上传时间： 2013-11-15
上传用户：zwei41
高的工作电压高达100V N双N沟道MOSFET同步驱动 The D810DCDC is a synchronous step-down switching regulator controller that can directly step-down voltages from up to 100V, making it ideal for telecom and automotive applications. The D810DCDC uses a constant on-time valley current control architecture to deliver very low duty cycles with accurate cycle-by-cycle current limit, without requiring a sense resistor. A precise internal reference provides 0.5% DC accuracy. A high bandwidth (25MHz) error amplifi er provides very fast line and load transient response. Large 1Ω gate drivers allow the D810DCDC to drive multiple MOSFETs for higher current applications. The operating frequency is selected by an external resistor and is compensated for variations in VIN and can also be synchronized to an external clock for switching-noise sensitive applications. Integrated bias control generates gate drive power from the input supply during start-up and when an output shortcircuit occurs, with the addition of a small external SOT23 MOSFET. When in regulation, power is derived from the output for higher effi ciency.
上传时间： 2013-10-24
上传用户：wd450412225
Advancements in board assembly, PCB layout anddigital IC integration have produced a new generationof densely populated, high performance systems. Theboard-mounted point-of-load (POL) DC/DC power suppliesin these systems are subject to the same demandingsize, high power and performance requirements asother subsystems. The rigorous new POL demands aredifficult to meet with traditional controller or regulatorICs, or power modules.
上传时间： 2014-12-24
上传用户：lbbyxmraon
Traditionally, an Electronic Circuit Breaker (ECB) comprisesa MOSFET, a MOSFET controller and a current senseresistor. The LTC®4213 does away with the sense resistorby using the RDS(ON) of the external MOSFET. The resultis a simple, small solution that offers a signifi cant lowinsertion loss advantage at low operating load voltage.The LTC4213 features two circuit breaking responses tovarying overload conditions with three selectable tripthresholds and a high side drive for an external N-channelMOSFET switch.
上传时间： 2014-03-02
上传用户：lixinxiang
A number of conventional solutions have been available forthe design of a DC/DC converter where the output voltageis within the input voltage range—a common scenarioin Li-Ion battery-powered applications—but none werevery attractive until now. Conventional topologies, suchas SEPIC or boost followed by buck, have numerousdisadvantages, including low effi ciency, complex magnetics,polarity inversion and/or circuit complexity/cost. TheLTC®3785 buck-boost controller yields a simple, effi cient,low parts-count, single-converter solution that is easyto implement, thus avoiding the drawbacks associatedwith traditional solutions.
上传时间： 2013-10-21
上传用户：ljt101007
To this day, Power over Ethernet (PoE) continues to gainpopularity in today’s networking world. The 12.95Wdelivered to the Powered Device (PD) input supplied bythe Power Sourcing Equipment (PSE) is a universal supply.Each PD provides its own DC/DC conversion from anominal 48V supply, thus eliminating the need for a correctvoltage wall adapter. However, higher power devicescan not take advantage of standard PoE because of itspower limitations, and must rely on a large wall adapteras their primary supply. The new LTC4268-1 breaks thispower barrier by allowing for power of up to 35W for suchpower-hungry 2-pair PoE applications. The LTC4268-1provides a complete solution by integrating a high powerPD interface control with an isolated fl yback controller.
上传时间： 2014-12-24
上传用户：jasson5678
