The PCA9548A is an octal bidirectional translating switch controlled via the I2C-bus. TheSCL/SDA upstream pair fans out to eight downstream pairs, or channels. Any individualSCx/SDx channel or combination of channels can be selected, determined by thecontents of the programmable control register.An active LOW reset input allows the PCA9548A to recover from a situation where one ofthe downstream I2C-buses is stuck in a LOW state. Pulling the RESET pin LOW resets theI2C-bus state machine and causes all the channels to be deselected as does the internalPower-on reset function.
上传时间： 2013-10-13
上传用户：bakdesec
The PCA9557 is a silicon CMOS circuit which provides parallel input/output expansion for SMBus and I2C-bus applications. The PCA9557 consists of an 8-bit input port register, 8-bit output port register, and an I2C-bus/SMBus interface. It has low current consumption and a high-impedance open-drain output pin, IO0. The system master can enable the PCA9557’s I/O as either input or output by writing to the configuration register. The system master can also invert the PCA9557 inputs by writing to the active HIGH polarity inversion register. Finally, the system master can reset the PCA9557 in the event of a time-out by asserting a LOW in the reset input. The power-on reset puts the registers in their default state and initializes the I2C-bus/SMBus state machine. The RESET pin causes the same reset/initialization to occur without de-powering the part.
上传时间： 2014-01-18
上传用户：bs2005
摘要：本水位监测报警器使用5V低压直流电源（也可以用3节5号电池代替）就可以对5~15厘米的水位进行监测，用LED显示和数码管显示水位，并可以对不再此范围内的水位发出报警。主要采用CD4066、74LS86、74LS32、CD4511芯片，再加上数码管、蜂鸣器、发光二极管、电阻这些器件组成一个简单而灵敏的监测报警电路，操作简单，接通电源即可工作。因为大部分电路采用数字电路，所以本水位监测报警器还具有耗能低、准确性高的特点。关键字：译码电路 报警电路 监测电路 Abstract: The water level alarm monitoring the use of 5 V low-voltage DC power (can also use three batteries replaced on the 5th) will be able to 5 to 15 centimeters of water level monitoring, with LED display and digital display of water level, and this can no longer Within the scope of a water level alarm. Mainly CD4066, 74LS86, 74LS32, CD4511 chips, coupled with digital control, buzzer, light-emitting diode, the resistance of these devices composed of a simple and sensitive monitoring alarm circuits. Because the majority of circuits using digital circuitry, so the water level monitored alarm system also has low energy consumption, high accuracy of the characteristics. Keyword: Decoding circuit alarm circuit monitoring circuit
上传时间： 2013-11-05
上传用户：王庆才
基于PIC单片机的低功耗读卡器硬件设计:本文提出了一个完整的基于串口的智能读卡器子系统设计方案并将其实现。读卡器的设计突出了小型化的要求，全部器件使用贴片封装。为了减小读卡器的体积，设计中还使用了串口窃电的技术，使用串口信号线直接给读卡器供电。为此，读卡器使用了省电的设计，采用了省电的集成电路，并大胆简化了许多传统的设计电路。关键字： 读卡器， 单片机， 串口窃电 Abstract： This paper aims to put forward a complete design of Smart IC card reader based onSerial Port and propose the way of realizing it for the purpose of Network Security. SMD isadopted to make Smart IC reader smaller in this design. To reduce the volume of Smart ICreader， Serial Port powered technology is employed to get power from the signal line of Serial Port. For this reason， low-power consumption components are adopted in the design and some traditional designs are simplified to reduce the power consumption.Keywords： Card Reader； Single-chip Computer； Serial Port Powered IC 卡系统保存了加密算法所需要的工作密钥，供加密算法对网络上传输的数据加密使用，是整个系统网络安全的核心。在IC 卡子系统中，读卡器是一个重要的部分。它起着管理IC卡、在IC 卡和PC或网络计算机间传递数据的重要作用。本文以一片PIC单片机为核心完成了基于RS232 串口的读卡器的硬件设计。
上传时间： 2014-04-14
上传用户：wanghui2438
基于单片机控制的二氧化碳浓度测试计:基于CDM4161二氧化碳气体浓度测试模块以及ATtiny26单片机,提出了一种二氧化碳浓度测试计的设计方案。该方案具有硬件电路简单、成本低、可靠性高、测量准确等优点，具有较高的实用价值。 Abstract: Abstract：A desigh scheme of CO2 concentration meter based on CDM4161carbon dioxide concentration test module and ATtiny26micro-controller is presented in this paper.The design scheme features simple hardware circuit,low-cost,high reli-ability，accurate measurement and it has a high practical value.
上传时间： 2013-11-14
上传用户：zjwangyichao
The solution presented in this paper and in the attached source files emulates the mostimportant SSC functions by using SW routines implemented in C. The code is focused onthe SAB C513, but will fit to all C500 derivatives.Beyond the low level software drivers a test shell is delivered. This shell allows a quicktest of the software drivers by an emulator or a starter kit demo board.
上传时间： 2013-11-24
上传用户：363186
The P90CL301 is a highly integrated 16/32 bit micro-controller especially suitable for applications requiring lowvoltage and low power consumption. It is fully software compatible with the 68000. Furthermore, it provides bothstandard as well as advanced peripheral functions on-chip.One of these peripheral functions is the I2C bus. This report describes worked-out driver software (written in C) toprogram the P90CL301 I2C interface. It also contains interface software routines offering the user a quick start inwriting a complete I2C system application.
上传时间： 2014-01-06
上传用户：气温达上千万的
The MC68HC05K0 is a low cost, low pin countsingle chip microcomputer with 504 bytes of userROM and 32 bytes of RAM. The MC68HC05K0 isa member of the 68HC05K series of devices whichare available in 16-pin DIL or SOIC packages.It uses the same CPU as the other devices in the68HC05 family and has the same instructions andregisters. Additionally, the device has a 15-stagemulti-function timer and 10 general purposebi-directional I/0 lines. A mask option is availablefor software programmable pull-downs on all ofthe I/O pins and four of the pins are capable ofgenerating interrupts.The device is ideally suited for remote-controlkeyboard applications because the pull-downs andthe interrupt drivers on the port pins allowkeyboards to be built without any externalcomponents except the keys themselves. There isno need for external pull-up or pull-down resistors,or diodes for wired-OR interrupts, as these featuresare already designed into the device.
上传时间： 2014-01-24
上传用户：zl5712176
当拿到一张CASE单时，首先得确定的是能用什么母体才能实现此功能，然后才能展开对外围硬件电路的设计，因此首先得了解每个母体的基本功能及特点，下面大至的介绍一下本公司常用的IC：单芯片解决方案• SN8P1900 系列– 高精度 16-Bit 模数转换器– 可编程运算放大器 (PGIA)• 信号放大低漂移: 2V• 放大倍数可编程: 1/16/64/128 倍– 升压- 稳压调节器 (Charge-Pump Regulator)• 电源输入: 2.4V ~ 5V• 稳压输出: e.g. 3.8V at SN8P1909– 内置液晶驱动电路 (LCD Driver)– 单芯片解决方案 • 耳温枪 SN8P1909 LQFP 80 Pins• 5000 解析度量测器 SN8P1908 LQFP 64 Pins• 体重计 SN8P1907 SSOP 48 Pins单芯片解决方案• SN8P1820 系列– 精确的12-Bit 模数转换器– 可编程运算放大器 (PGIA)• Gain Stage One: Low Offset 5V, Gain: 16/32/64/128• Gain Stage One: Low Offset 2mV, Gain: 1.3 ~ 2.5– 升压- 稳压调节器• 电源输入: 2.4V ~ 5V• 稳压输出: e.g. 3.8V at SN8P1829– 内置可编程运算放大电路– 内置液晶驱动电路 – 单芯片解决方案 • 电子医疗器 SN8P1829 LQFP 80 Pins 高速/低功耗/高可靠性微控制器• 最新SN8P2000 系列– SN8P2500/2600/2700 系列– 高度抗交流杂讯能力• 标准瞬间电压脉冲群测试 (EFT): IEC 1000-4-4• 杂讯直接灌入芯片电源输入端• 只需添加1颗 2.2F/50V 旁路电容• 测试指标稳超 4000V (欧规)– 高可靠性复位电路保证系统正常运行• 支持外部复位和内部上电复位• 内置1.8V 低电压侦测可靠复位电路• 内置看门狗计时器保证程序跳飞可靠复位– 高抗静电/栓锁效应能力– 芯片工作温度有所提高: -200C ~ 700C 工规芯片温度： -400C ~ 850C 高速/低功耗/高可靠性微控制器• 最新 SN8P2000 系列– SN8P2500/2600/2700 系列– 1T 精简指令级结构• 1T: 一个外部振荡周期执行一条指令• 工作速度可达16 MIPS / 16 MHz Crystal– 工作消耗电流 < 2mA at 1-MIPS/5V– 睡眠模式下消耗电流 < 1A / 5V额外功能• 高速脉宽调制输出 (PWM)– 8-Bit PWM up to 23 KHz at 12 MHz System Clock– 6-Bit PWM up to 93 KHz at 12 MHz System Clock– 4-Bit PWM up to 375 KHz at 12 MHz System Clock• 内置高速16 MHz RC振荡器 (SN8P2501A)• 电压变化唤醒功能• 可编程控制沿触发/中断功能– 上升沿 / 下降沿 / 双沿触发• 串行编程接口
上传时间： 2013-10-21
上传用户：jiahao131
//芯片资料请到www.elecfans.com查找 //DS1820 C51 子程序//这里以11.0592M晶体为例，不同的晶体速度可能需要调整延时的时间//sbit DQ =P2^1;//根据实际情况定义端口 typedef unsigned char byte;typedef unsigned int word; //延时void delay(word useconds){ for(;useconds>0;useconds--);} //复位byte ow_reset(void){ byte presence; DQ = 0; //pull DQ line low delay(29); // leave it low for 480us DQ = 1; // allow line to return high delay(3); // wait for presence presence = DQ; // get presence signal delay(25); // wait for end of timeslot return(presence); // presence signal returned} // 0=presence, 1 = no part //从 1-wire 总线上读取一个字节byte read_byte(void){ byte i; byte value = 0; for (i=8;i>0;i--) { value>>=1; DQ = 0; // pull DQ low to start timeslot DQ = 1; // then return high delay(1); //for (i=0; i<3; i++); if(DQ)value|=0x80; delay(6); // wait for rest of timeslot } return(value);} //向 1-WIRE 总线上写一个字节void write_byte(char val){ byte i; for (i=8; i>0; i--) // writes byte, one bit at a time { DQ = 0; // pull DQ low to start timeslot DQ = val&0x01; delay(5); // hold value for remainder of timeslot DQ = 1; val=val/2; } delay(5);} //读取温度char Read_Temperature(void){ union{ byte c[2]; int x; }temp; ow_reset(); write_byte(0xCC); // Skip ROM write_byte(0xBE); // Read Scratch Pad temp.c[1]=read_byte(); temp.c[0]=read_byte(); ow_reset(); write_byte(0xCC); //Skip ROM write_byte(0x44); // Start Conversion return temp.x/2;}
上传时间： 2013-11-03
上传用户：hongmo
