虫虫首页| 资源下载| 资源专辑| 精品软件
登录| 注册

full-wave

  • MEMS麦克风有助于提高系统设计效率

    A MEMS microphone IC is unique among Analog Devices, Inc., products in that its input is an acoustic pressure wave. For this reason, some specifications included in the data sheets for these parts may not be familiar, or familiar specifications may be applied in unfamiliar ways. This application note explains the specifica-tions and terms found in MEMS microphone data sheets so that the microphone can be appropriately designed into a system.

    标签: MEMS 麦克风 系统设计 效率

    上传时间: 2013-10-31

    上传用户:masochism

  • DAC技术用语 (D/A Converters Defini

    Differential Nonlinearity: Ideally, any two adjacent digitalcodes correspond to output analog voltages that are exactlyone LSB apart. Differential non-linearity is a measure of theworst case deviation from the ideal 1 LSB step. For example,a DAC with a 1.5 LSB output change for a 1 LSB digital codechange exhibits 1⁄2 LSB differential non-linearity. Differentialnon-linearity may be expressed in fractional bits or as a percentageof full scale. A differential non-linearity greater than1 LSB will lead to a non-monotonic transfer function in aDAC.Gain Error (Full Scale Error): The difference between theoutput voltage (or current) with full scale input code and theideal voltage (or current) that should exist with a full scale inputcode.Gain Temperature Coefficient (Full Scale TemperatureCoefficient): Change in gain error divided by change in temperature.Usually expressed in parts per million per degreeCelsius (ppm/°C).Integral Nonlinearity (Linearity Error): Worst case deviationfrom the line between the endpoints (zero and full scale).Can be expressed as a percentage of full scale or in fractionof an LSB.LSB (Lease-Significant Bit): In a binary coded system thisis the bit that carries the smallest value or weight. Its value isthe full scale voltage (or current) divided by 2n, where n is theresolution of the converter.Monotonicity: A monotonic function has a slope whose signdoes not change. A monotonic DAC has an output thatchanges in the same direction (or remains constant) for eachincrease in the input code. the converse is true for decreasing codes.

    标签: Converters Defini DAC

    上传时间: 2013-10-30

    上传用户:stvnash

  • ADC转换器技术用语 (A/D Converter Defi

    ANALOG INPUT BANDWIDTH is a measure of the frequencyat which the reconstructed output fundamental drops3 dB below its low frequency value for a full scale input. Thetest is performed with fIN equal to 100 kHz plus integer multiplesof fCLK. The input frequency at which the output is −3dB relative to the low frequency input signal is the full powerbandwidth.APERTURE JITTER is the variation in aperture delay fromsample to sample. Aperture jitter shows up as input noise.APERTURE DELAY See Sampling Delay.BOTTOM OFFSET is the difference between the input voltagethat just causes the output code to transition to the firstcode and the negative reference voltage. Bottom Offset isdefined as EOB = VZT–VRB, where VZT is the first code transitioninput voltage and VRB is the lower reference voltage.Note that this is different from the normal Zero Scale Error.CONVERSION LATENCY See PIPELINE DELAY.CONVERSION TIME is the time required for a completemeasurement by an analog-to-digital converter. Since theConversion Time does not include acquisition time, multiplexerset up time, or other elements of a complete conversioncycle, the conversion time may be less than theThroughput Time.DC COMMON-MODE ERROR is a specification which appliesto ADCs with differential inputs. It is the change in theoutput code that occurs when the analog voltages on the twoinputs are changed by an equal amount. It is usually expressed in LSBs.

    标签: Converter Defi ADC 转换器

    上传时间: 2013-11-12

    上传用户:pans0ul

  • pwm教程

    The equal-area theorem●This is sinusoidal PWM (SPWM)●The equal-area theorem can be appliedto realize any shape of waveforms ●Natural sampling●Calculation based on equal-area criterion●Selected harmonic elimination●Regular sampling●Hysteresis-band control●Triangular wave comparison withfeedback control

    标签: pwm 教程

    上传时间: 2013-11-22

    上传用户:linyao

  • 数字与模拟电路设计技巧

    数字与模拟电路设计技巧IC与LSI的功能大幅提升使得高压电路与电力电路除外,几乎所有的电路都是由半导体组件所构成,虽然半导体组件高速、高频化时会有EMI的困扰,不过为了充分发挥半导体组件应有的性能,电路板设计与封装技术仍具有决定性的影响。 模拟与数字技术的融合由于IC与LSI半导体本身的高速化,同时为了使机器达到正常动作的目的,因此技术上的跨越竞争越来越激烈。虽然构成系统的电路未必有clock设计,但是毫无疑问的是系统的可靠度是建立在电子组件的选用、封装技术、电路设计与成本,以及如何防止噪讯的产生与噪讯外漏等综合考虑。机器小型化、高速化、多功能化使得低频/高频、大功率信号/小功率信号、高输出阻抗/低输出阻抗、大电流/小电流、模拟/数字电路,经常出现在同一个高封装密度电路板,设计者身处如此的环境必需面对前所未有的设计思维挑战,例如高稳定性电路与吵杂(noisy)性电路为邻时,如果未将噪讯入侵高稳定性电路的对策视为设计重点,事后反复的设计变更往往成为无解的梦魇。模拟电路与高速数字电路混合设计也是如此,假设微小模拟信号增幅后再将full scale 5V的模拟信号,利用10bit A/D转换器转换成数字信号,由于分割幅宽祇有4.9mV,因此要正确读取该电压level并非易事,结果造成10bit以上的A/D转换器面临无法顺利运作的窘境。另一典型实例是使用示波器量测某数字电路基板两点相隔10cm的ground电位,理论上ground电位应该是零,然而实际上却可观测到4.9mV数倍甚至数十倍的脉冲噪讯(pulse noise),如果该电位差是由模拟与数字混合电路的grand所造成的话,要测得4.9 mV的信号根本是不可能的事情,也就是说为了使模拟与数字混合电路顺利动作,必需在封装与电路设计有相对的对策,尤其是数字电路switching时,ground vance noise不会入侵analogue ground的防护对策,同时还需充分检讨各电路产生的电流回路(route)与电流大小,依此结果排除各种可能的干扰因素。以上介绍的实例都是设计模拟与数字混合电路时经常遇到的瓶颈,如果是设计12bit以上A/D转换器时,它的困难度会更加复杂。

    标签: 数字 模拟电路 设计技巧

    上传时间: 2013-11-16

    上传用户:731140412

  • PCB设计经典资料

    本文将接续介绍电源与功率电路基板,以及数字电路基板导线设计。宽带与高频电路基板导线设计a.输入阻抗1MHz,平滑性(flatness)50MHz 的OP增幅器电路基板图26 是由FET 输入的高速OP 增幅器OPA656 构成的高输入阻抗OP 增幅电路,它的gain取决于R1、R2,本电路图的电路定数为2 倍。此外为改善平滑性特别追加设置可以加大噪讯gain,抑制gain-频率特性高频领域时峰值的R3。图26 高输入阻抗的宽带OP增幅电路图27 是高输入阻抗OP 增幅器的电路基板图案。降低高速OP 增幅器反相输入端子与接地之间的浮游容量非常重要,所以本电路的浮游容量设计目标低于0.5pF。如果上述部位附着大浮游容量的话,会成为高频领域的频率特性产生峰值的原因,严重时频率甚至会因为feedback 阻抗与浮游容量,造成feedback 信号的位相延迟,最后导致频率特性产生波动现象。此外高输入阻抗OP 增幅器输入部位的浮游容量也逐渐成为问题,图27 的电路基板图案的非反相输入端子部位无full ground设计,如果有外部噪讯干扰之虞时,接地可设计成网格状(mesh)。图28 是根据图26 制成的OP 增幅器Gain-频率特性测试结果,由图可知即使接近50MHz频率特性非常平滑,-3dB cutoff频率大约是133MHz。

    标签: PCB

    上传时间: 2013-11-13

    上传用户:hebanlian

  • 磁芯电感器的谐波失真分析

    磁芯电感器的谐波失真分析 摘  要:简述了改进铁氧体软磁材料比损耗系数和磁滞常数ηB,从而降低总谐波失真THD的历史过程,分析了诸多因数对谐波测量的影响,提出了磁心性能的调控方向。 关键词:比损耗系数, 磁滞常数ηB ,直流偏置特性DC-Bias,总谐波失真THD  Analysis on THD of the fer rite co res u se d i n i nductancShi Yan Nanjing Finemag Technology Co. Ltd., Nanjing 210033   Abstract:    Histrory of decreasing THD by improving the ratio loss coefficient and hysteresis constant of soft magnetic ferrite is briefly narrated. The effect of many factors which affect the harmonic wave testing is analysed. The way of improving the performance of ferrite cores is put forward.  Key words: ratio loss coefficient,hysteresis constant,DC-Bias,THD  近年来,变压器生产厂家和软磁铁氧体生产厂家,在电感器和变压器产品的总谐波失真指标控制上,进行了深入的探讨和广泛的合作,逐步弄清了一些似是而非的问题。从工艺技术上采取了不少有效措施,促进了质量问题的迅速解决。本文将就此热门话题作一些粗浅探讨。  一、 历史回顾 总谐波失真(Total harmonic distortion) ,简称THD,并不是什么新的概念,早在几十年前的载波通信技术中就已有严格要求<1>。1978年邮电部公布的标准YD/Z17-78“载波用铁氧体罐形磁心”中,规定了高μQ材料制作的无中心柱配对罐形磁心详细的测试电路和方法。如图一电路所示,利用LC组成的150KHz低通滤波器在高电平输入的情况下测量磁心产生的非线性失真。这种相对比较的实用方法,专用于无中心柱配对罐形磁心的谐波衰耗测试。 这种磁心主要用于载波电报、电话设备的遥测振荡器和线路放大器系统,其非线性失真有很严格的要求。  图中  ZD   —— QF867 型阻容式载频振荡器,输出阻抗 150Ω, Ld47 —— 47KHz 低通滤波器,阻抗 150Ω,阻带衰耗大于61dB,       Lg88 ——并联高低通滤波器,阻抗 150Ω,三次谐波衰耗大于61dB Ld88 ——并联高低通滤波器,阻抗 150Ω,三次谐波衰耗大于61dB FD   —— 30~50KHz 放大器, 阻抗 150Ω, 增益不小于 43 dB,三次谐波衰耗b3(0)≥91 dB, DP  —— Qp373 选频电平表,输入高阻抗, L ——被测无心罐形磁心及线圈, C  ——聚苯乙烯薄膜电容器CMO-100V-707APF±0.5%,二只。 测量时,所配用线圈应用丝包铜电磁线SQJ9×0.12(JB661-75)在直径为16.1mm的线架上绕制 120 匝, (线架为一格) , 其空心电感值为 318μH(误差1%) 被测磁心配对安装好后,先调节振荡器频率为 36.6~40KHz,  使输出电平值为+17.4 dB, 即选频表在 22′端子测得的主波电平 (P2)为+17.4 dB,然后在33′端子处测得输出的三次谐波电平(P3), 则三次谐波衰耗值为:b3(+2)= P2+S+ P3 式中:S 为放大器增益dB 从以往的资料引证, 就可以发现谐波失真的测量是一项很精细的工作,其中测量系统的高、低通滤波器,信号源和放大器本身的三次谐波衰耗控制很严,阻抗必须匹配,薄膜电容器的非线性也有相应要求。滤波器的电感全由不带任何磁介质的大空心线圈绕成,以保证本身的“洁净” ,不至于造成对磁心分选的误判。 为了满足多路通信整机的小型化和稳定性要求, 必须生产低损耗高稳定磁心。上世纪 70 年代初,1409 所和四机部、邮电部各厂,从工艺上改变了推板空气窑烧结,出窑后经真空罐冷却的落后方式,改用真空炉,并控制烧结、冷却气氛。技术上采用共沉淀法攻关试制出了μQ乘积 60 万和 100 万的低损耗高稳定材料,在此基础上,还实现了高μ7000~10000材料的突破,从而大大缩短了与国外企业的技术差异。当时正处于通信技术由FDM(频率划分调制)向PCM(脉冲编码调制) 转换时期, 日本人明石雅夫发表了μQ乘积125 万为 0.8×10 ,100KHz)的超优铁氧体材料<3>,其磁滞系数降为优铁

    标签: 磁芯 电感器 谐波失真

    上传时间: 2014-12-24

    上传用户:7891

  • 华硕内部的PCB基本规范

    PCB LAYOUT 基本規範項次 項目 備註1 一般PCB 過板方向定義:􀀹 PCB 在SMT 生產方向為短邊過迴焊爐(Reflow), PCB 長邊為SMT 輸送帶夾持邊.􀀹 PCB 在DIP 生產方向為I/O Port 朝前過波焊爐(Wave Solder), PCB 與I/O 垂直的兩邊為DIP 輸送帶夾持邊.1.1 金手指過板方向定義:􀀹 SMT: 金手指邊與SMT 輸送帶夾持邊垂直.􀀹 DIP: 金手指邊與DIP 輸送帶夾持邊一致.2 􀀹 SMD 零件文字框外緣距SMT 輸送帶夾持邊L1 需≧150 mil.􀀹 SMD 及DIP 零件文字框外緣距板邊L2 需≧100 mil.3 PCB I/O port 板邊的螺絲孔(精靈孔)PAD 至PCB 板邊, 不得有SMD 或DIP 零件(如右圖黃色區).PAD

    标签: PCB 华硕

    上传时间: 2014-12-24

    上传用户:jokey075

  • 高性能DCDC控制器

    We provide complete power solutions with a full lineup of power managementproducts. This brochure provides an overview of our high performance DC/DC switching regulatorcontrollers for applications including datacom, telecom, industrial, automotive, medical, avionicsand control systems. We make power design easier with our industry-leading field applicationengineering support; a broad selection of demonstration boards with schematics, layout filesand parts lists; SwitcherCAD® software for simulation, application notes and comprehensivetechnical documentation.

    标签: DCDC 性能 控制器

    上传时间: 2013-10-15

    上传用户:lz4v4

  • 优化输电线路 精确测量电压驻波比(VSWR)

    Abstract: Impedance mismatches in a radio-frequency (RF) electrical transmission line cause power loss andreflected energy. Voltage standing wave ratio (VSWR) is a way to measure transmission line imperfections. Thistutorial defines VSWR and explains how it is calculated. Finally, an antenna VSWR monitoring system is shown.

    标签: VSWR 输电线路 精确测量 电压驻波比

    上传时间: 2013-10-19

    上传用户:yuanwenjiao