Much has been written concerning the manner in which healthcare is changing, with a particular emphasis on how very large quantities of data are now being routinely collected during the routine care of patients. The use of machine learning meth- ods to turn these ever-growing quantities of data into interventions that can improve patient outcomes seems as if it should be an obvious path to take. However, the field of machine learning in healthcare is still in its infancy. This book, kindly supported by the Institution of Engineering andTechnology, aims to provide a “snap- shot” of the state of current research at the interface between machine learning and healthcare.
标签： Technologies Healthcare Learning Machine
上传时间： 2020-06-10
上传用户：shancjb
高通(Qualcomm)蓝牙芯片QCC5151_硬件设计详细指导书（官方内部培训手册）共52页其内容是针对硬件设计、部分重要元器件选择(ESD，Filter）及走线注意事项的详细说明。2 Power management 2.1 SMPS 2.1.1 Components specification 2.1.2 Input power supply selection 2.1.3 Minimize SMPS EMI emissions 2.1.4 Internal LDOs and digital core decoupling 2.1.5 Powering external components 2.2 Charger 2.2.1 Charger connections.2.2.2 General charger operation2.2.3 Temperature measurement during charging 2.3 SYS_CTRL 3 Bluetooth radio3.1 RF PSU component choice 3.2 RF band-pass filter3.3 Layout (天线 走线的注意事项)4 Audio4.1 Audio bypass capacitors 4.2 Earphone speaker output4.3 Line/Mic input 4.4 Headphone output optimizition5 LED pads 5.1 LED driver 5.2 Digital/Button input 5.3 Analog input5.4 Disabled 6 Reset pin (Reset#)7 QSPIinterface 8 USB interfaces 8.1 USB device port8.1.1 USB connections8.1.2 Layout notes8.1.3 USB charger detection
上传时间： 2022-01-24
上传用户：XuVshu
The PW4055 is a complete constant-current /constant-voltage linear charger for single cell lithiumion batteries.Its ThinSOT package and low external component count make the PW4055 ideallysuited for portable applications.Furthermore, the PW4055 is specifically designed to work within USBpower specifications.The PW4055 No external sense resistor is needed, and no blocking diode is required due to theinternal MOSFET architecture.Thermal feedback regulates the charge current to limit the dietemperature during high power operation or high ambient temperature. The charge voltage is fixedat 4.2V, and the charge current can be programmed externally with a single resistor. The PW4055automatically terminates the charge cycle when the charge current drops to 1/10th the programmedvalue after the final float voltage is reached. When the input supply (wall adapter or USB supply) isremoved, the PW4055 automatically enters a low current state, dropping the battery drain currentto less than 2µA. The PW4055 can be put into shutdown mode, reducing the supply current to 25µA.The BAT pin has a 7KV ESD(HBM) capability. Other features include charge current monitor, undervoltage lockout, automatic recharge and a status pin to indicate charge termination and the presenceof an input voltage
标签： pw4055
上传时间： 2022-02-11
上传用户：jason_vip1
The PW2228A is a high efficiency single inductor Buck-Boost converter which can supply theload current up to 1.5A. It provides auto-transition between Buck and Boost Mode. The PW2228Aoperates at 2.4MHz switching frequency in CCM. DC/DC converter operates at Pulse-Skipping Modeat light load. The output voltage is programmable using an external resistor divider, or is fixed to3.3V internally. The load is disconnected from the VIN during shutdown.The PW2228A is available in TDFN3X3-10 package.
标签： pw2228a
上传时间： 2022-02-11
上传用户：
PW1555 is a programmable current limit switch with input voltage range selection and outputvoltage clamping. Extremely low RDS(ON) of the integrated protection N-channel FET helps toreduce power loss during the normal operation. Programmable soft-start time controls the slew rateof the output voltage during the start-up time. Independent enable control allows the complicatedsystem sequencing control. It integrates the over-temperature protection shutdown andautorecovery with hystersis
标签： pw1555
上传时间： 2022-02-14
上传用户：
本系统采用电动机电枢供电回路串接采样电阻的方式来实现对小型直流有刷电动机的转速测量。该系统主要由二阶低通滤波电路,小信号放大电路、单片机测量显示电路、开关稳压电源电路等组成。同时自制电机测速装置,用高频磁环作为载体,用线圈绕制磁环,利用电磁感应原理检测电机运行时的漏磁,将变化的磁场信号转化为磁环上的感应电流。用信号处理单元电路将微弱电信号转化为脉冲信号,送由单片机检测,从而达到准确测量电机的速度的要求。In this system, the sampling resistance of armature power supply circuit is connected in series to measure the speed of small DC brush motor. The system is mainly composed of second-order low-pass filter circuit, small signal amplifier circuit, single-chip measurement and display circuit, switching regulated power supply circuit and so on. At the same time, the self-made motor speed measuring device uses high frequency magnetic ring as the carrier, coil winding magnetic ring, and electromagnetic induction principle to detect the leakage of magnetic field during the operation of the motor, which converts the changed magnetic field signal into the induced current on the magnetic ring. The weak electric signal is transformed into pulse signal by signal processing unit circuit, which is sent to single chip computer for detection, so as to meet the requirement of accurate measurement of motor speed.
标签： 直流电动机
上传时间： 2022-03-26
上传用户：
设计功率MOSFET驱动电路时需重点考虑寄生参数对电路的影响。米勒电容作为MOSFET器件的一项重要参数,在驱动电路的设计时需要重点关注。重点观察了MOSFET的开通和关断过程中栅极电压、漏源极电压和漏源极电流的变化过程,并分析了米勒电容、寄生电感等寄生参数对漏源极电压和漏源极电流的影响。分析了栅极电压在米勒平台附近产生振荡的原因,并提出了抑制措施,对功率MOSFET的驱动设计具有一定的指导意义。When designing the drive circuit of power MOSFET,the influence of parasitic parameters on the circuit should be concerned.As an important parameter of MOSFET device,Miller capacitance should be considered in the design of drive circuit.The variation of gate voltage,drain source voltage and drain source current during the turn-on and turn-off of MOSFET were observed.The influences of parasitic parameters such as Miller capacitance and parasitic inductance on drain source voltage and drain source current were analyzed.The reasons of gate voltage oscillation nearby Miller plateau were analyzed,and the restraining measures were put forward.This research was instructive for the drive design of power MOSFET.
标签： mosfet
上传时间： 2022-04-02
上传用户：默默
高通(Qualcomm)蓝牙芯片QCC5144_硬件设计详细指导书（官方内部培训手册）其内容是针对硬件设计、部分重要元器件选择(ESD，Filter）及走线注意事项的详细说明。2 Power management 2.1 SMPS 2.1.1 Components specification 2.1.2 Input power supply selection 92.1.3 Minimize SMPS EMI emissions 2.1.4 Internal LDOs and digital core decoupling 2.1.5 Powering external components 2.2 Charger 2.2.1 Charger connections.2.2.2 General charger operation2.2.3 Temperature measurement during charging 2.3 SYS_CTRL 3 Bluetooth radio3.1 RF PSU component choice 3.2 RF band-pass filter3.3 Layout (天线 走线的注意事项)4 Audio4.1 Audio bypass capacitors 4.2 Earphone speaker output4.3 Line/Mic input 4.4 Headphone output optimizition5 LED pads 5.1 LED driver 5.2 Digital/Button input 5.3 Analog input5.4 Disabled 6 Reset pin (Reset#)7 USB interfaces7.1 USB device port7.1.1 USB device port7.1.2 Layout notes 7.1.3 USB charger detectionA QCC5144 VFBGA example schematic and BOM B Recommended SMPS components specificationB.1 Inductor specifition B.2 Recommended inductors B.3 SMPS capacitor specifition
上传时间： 2022-04-07
上传用户：默默
Prefaceduring the past years, there has been a quickly rising interest in radio access technologies for providingmobile as well as nomadic and fixed services for voice, video, and data. The difference indesign, implementation, and use between telecom and datacom technologies is also becoming moreblurred. One example is cellular technologies from the telecom world being used for broadband dataand wireless LAN from the datacom world being used for voice-over IP.Today, the most widespread radio access technology for mobile communication is digital cellular,with the number of users passing 5 billion by 2010, which is more than half of the world’s population.It has emerged from early deployments of an expensive voice service for a few car-borne users,to today’s widespread use of mobile-communication devices that provide a range of mobile servicesand often include camera, MP3 player, and PDA functions. With this widespread use and increasinginterest in mobile communication, a continuing evolution ahead is foreseen.This book describes LTE, developed in 3GPP (Third Generation Partnership Project) and providingtrue 4G broadband mobile access, starting from the first version in release 8 and through the continuingevolution to release 10, the latest version of LTE. Release 10, also known as LTE-Advanced,is of particular interest as it is the major technology approved by the ITU as fulfilling the IMTAdvancedrequirements. The description in this book is based on LTE release 10 and thus provides acomplete description of the LTE-Advanced radio access from the bottom up.Chapter 1 gives the background to LTE and its evolution, looking also at the different standardsbodies and organizations involved in the process of defining 4G. It also gives a discussion of the reasonsand driving forces behind the evolution.Chapters 2–6 provide a deeper insight into some of the technologies that are part of LTE and itsevolution. Because of its generic nature, these chapters can be used as a background not only for LTEas described in this book, but also for readers who want to understand the technology behind othersystems, such as WCDMA/HSPA, WiMAX, and CDMA2000.Chapters 7–17 constitute the main part of the book. As a start, an introductory technical overviewof LTE is given, where the most important technology components are introduced based onthe generic technologies described in previous chapters. The following chapters provide a detaileddescription of the protocol structure, the downlink and uplink transmission schemes, and the associatedmechanisms for scheduling, retransmission and interference handling. Broadcast operation andrelaying are also described. This is followed by a discussion of the spectrum flexibility and the associated
上传时间： 2022-07-08
上传用户：
