The PAM2862 is a continuous mode inductivestep-down converter, designed for driving singleor multiple series connected LEDs efficientlyfrom a voltage source higher than the LEDvoltage. The device operates from an inputupply between 6V and 30V and provides anexternally adjustable output current of up to 1A.Depending upon supply voltage and externalcomponents, this can provide up to 24 watts ofoutput power.
上传时间： 2013-11-16
上传用户：司令部正军级
The PCA9517 is a CMOS integrated circuit that provides level shifting between lowvoltage (down to 0.9 V) and higher voltage (2.7 V to 5.5 V) I2C-bus or SMBus applications.While retaining all the operating modes and features of the I2C-bus system during thelevel shifts, it also permits extension of the I2C-bus by providing bidirectional buffering forboth the data (SDA) and the clock (SCL) lines, thus enabling two buses of 400 pF. Usingthe PCA9517 enables the system designer to isolate two halves of a bus for both voltageand capacitance. The SDA and SCL pins are over voltage tolerant and arehigh-impedance when the PCA9517 is unpowered.
标签： translating Level 9517 PCA
上传时间： 2013-12-25
上传用户：wsf950131
The TL2575 and TL2575HV represent superior alternatives to popular three-terminal linear regulators. Due totheir high efficiency, the devices significantly reduce the size of the heatsink and, in many cases, no heatsink isrequired. Optimized for use with standard series of inductors available from several different manufacturers, theTL2575 and TL2575HV greatly simplify the design of switch-mode power supplies by requiring a minimaladdition of only four to six external components for operation.
标签： STEP-DOWN SWITCHING SIMPLE 1A
上传时间： 2013-11-20
上传用户：jelenecheung
The MAX3243E device consists of three line drivers, five line receivers, and a dual charge-pump circuit with±15-kV ESD (HBM and IEC61000-4-2, Air-Gap Discharge) and ±8-kV ESD (IEC61000-4-2, Contact Discharge)protection on serial-port connection pins. The device meets the requirements of TIA/EIA-232-F and provides theelectrical interface between an asynchronous communication controller and the serial-port connector. Thiscombination of drivers and receivers matches that needed for the typical serial port used in an IBM PC/AT, orcompatible. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-Vsupply. In addition, the device includes an always-active noninverting output (ROUT2B), which allowsapplications using the ring indicator to transmit data while the device is powered down. The device operates atdata signaling rates up to 250 kbit/s and a maximum of 30-V/ms driver output slew rate.
标签： MULTICHANNEL 5.5 TO RS
上传时间： 2013-10-19
上传用户：ddddddd
The MC68HC05K0 is a low cost, low pin countsingle chip microcomputer with 504 bytes of userROM and 32 bytes of RAM. The MC68HC05K0 isa member of the 68HC05K series of devices whichare available in 16-pin DIL or SOIC packages.It uses the same CPU as the other devices in the68HC05 family and has the same instructions andregisters. Additionally, the device has a 15-stagemulti-function timer and 10 general purposebi-directional I/0 lines. A mask option is availablefor software programmable pull-downs on all ofthe I/O pins and four of the pins are capable ofgenerating interrupts.The device is ideally suited for remote-controlkeyboard applications because the pull-downs andthe interrupt drivers on the port pins allowkeyboards to be built without any externalcomponents except the keys themselves. There isno need for external pull-up or pull-down resistors,or diodes for wired-OR interrupts, as these featuresare already designed into the device.
上传时间： 2014-01-24
上传用户：zl5712176
The STWD100 watchdog timer circuits are self-contained devices which prevent systemfailures that are caused by certain types of hardware errors (non-responding peripherals,bus contention, etc.) or software errors (bad code jump, code stuck in loop, etc.).The STWD100 watchdog timer has an input, WDI, and an output, WDO (see Figure 2). Theinput is used to clear the internal watchdog timer periodically within the specified timeoutperiod, twd (see Section 3: Watchdog timing). While the system is operating correctly, itperiodically toggles the watchdog input, WDI. If the system fails, the watchdog timer is notreset, a system alert is generated and the watchdog output, WDO, is asserted (seeSection 3: Watchdog timing).The STWD100 circuit also has an enable pin, EN (see Figure 2), which can enable ordisable the watchdog functionality. The EN pin is connected to the internal pull-downresistor. The device is enabled if the EN pin is left floating.
上传时间： 2013-10-22
上传用户：taiyang250072
基于USB接口的数据采集模块的设计与实现Design and Implementation of USB-Based Data Acquisition Module路 永 伸(天津科技大学电子信息与自动化学院，天津300222)摘要文中给出基于USB接口的数据采集模块的设计与实现。硬件设计采用以Adpc831与PDIUSBDI2为主的器件进行硬件设计，采用Windriver开发USB驱动，并用Visual C十十6.0对主机软件中硬件接口操作部分进行动态链接库封装。关键词USB 数据采集Adpc831 PDNSBDI2 Windriver动态链接库Abstract T hed esigna ndim plementaitono fU SB-BasedD ataA cquisiitonM oduleis g iven.Th ec hips oluitonm ainlyw ithA dpc831a ndP DTUSBD12i sused for hardware design. The USB drive is developed场Wmdriver, and the operation on the hardware interface is packaged into Dynamic Link Libraries场Visual C++6.0. Keywords USB DataA cquisition Adttc831 PDfUSBD12 Windriver0 引言US B总 线 是新一代接口总线，最初推出的目的是为了统一取代PC机的各类外设接口，迄今经历了1.0,1.1与2.0版本3个标准。在国内基于USB总线的相关设计与开发也得到了快速的发展，很多设计者从各自的应用领域，用不同方案设计出了相应的装置[1,2]。数据采集是工业控制中一个普遍而重要的环节，因此开发基于USB接口的数据采集模块具有很强的现实应用意义。虽然 US B总线标准已经发展到2.0版本，但由于工业控制现场干扰信号的情况比较复杂，高速数据传输的可靠性不容易被保证，并且很多场合对数据采集的实时性要求并不高，开发2.0标准产品的成本又较1.1标准产品高，所以笔者认为，在工业控制领域，目前开发基于USB总线1.1标准实现的数据采集模块的实用意义大于相应2.0标准模块。
上传时间： 2013-10-23
上传用户：q3290766
（Portmon is an application that lets you monitor serial and parallel activity on your local system, or any computer on the network that you can reach via TCP/IP. It is the most powerful tool available for tracking down port-related configuration problems and analyzing application port usage.）
上传时间： 2013-11-07
上传用户：1412904892
Introduction to Xilinx Packaging Electronic packages are interconnectable housings for semiconductor devices. The major functions of the electronic packages are to provide electrical interconnections between the IC and the board and to efficiently remove heat generated by the device. Feature sizes are constantly shrinking, resulting in increased number of transistors being packed into the device. Today's submicron technology is also enabling large-scale functional integration and system-on-a-chip solutions. In order to keep pace with these new advancements in silicon technologies, semiconductor packages have also evolved to provide improved device functionality and performance. Feature size at the device level is driving package feature sizes down to the design rules of the early transistors. To meet these demands, electronic packages must be flexible to address high pin counts, reduced pitch and form factor requirements. At the same time,packages must be reliable and cost effective.
上传时间： 2013-10-22
上传用户：ztj182002
The SDI standards are the predominant standards for uncompressed digital videointerfaces in the broadcast studio and video production center. The first SDI standard,SD-SDI, allowed standard-definition digital video to be transported over the coaxial cableinfrastructure initially installed in studios to carry analog video. Next, HD-SDI wasto support high-definition video. Finally, dual link HD-SDI and 3G-SDIdoubled the bandwidth of HD-SDI to support 1080p (50 Hz and 60 Hz) and other videoformats requiring more bandwidth than HD-SDI provides.
上传时间： 2013-10-08
上传用户：yjj631
