C8051F020单片机通过SPI接口驱动四线电阻式触摸屏控制器TSC2046，利用中断方式驱动TSC2046设计软件。介绍了触摸屏的工作原理、TSC2046工作方式以及典型应用电路。 Abstract: The C8051F020 MCU is connected with the TSC2046 which is a 4-wire touch screen controller. The TSC2046 is controlled by interrupt mode, the? operation principle of touch screen is introduced. The operation mode of TSC2046 and typical application circuit are also discussed.
上传时间： 2014-12-27
上传用户：hwl453472107
介绍了MPC555与CS8900A扩展以太网的硬件设计图。以NUCLUES PLUS操作系统为基础，介绍了网卡软件驱动程序的编制，给出了以太网协议包嵌入NUCLEUS PLUS操作系统的实现方法。 Abstract: The Ethernet extension hardware design of MPC555 and CS8900A are introduced,and the software driven program based on NUCLEUS PLUS operation system and the technique that Ethernet protocol embedded in NUCLEUS PLUS real operation system are discussed.
上传时间： 2013-10-23
上传用户：xiehao13
介绍基于ATmega8型单片机的温度测量及加热控制系统。分析系统的工作原理，详尽讨论系统的硬件电路和软件流程。实验证明，该系统工作可靠，稳定性高。 Abstract: The new temperature measuring and heating control system based on ATmega8 MCU is introduced.The system’s working principles is analyzed.The design principles of hardware and software are also discussed in detail.This system has been testified and it works steady and reliably.
上传时间： 2013-11-21
上传用户：caiguoqing
介绍了CAN总线和P87C591单片机的特点，给出了基于P87C591单片机的信号采集节点的软、硬件设计，指出了硬件电路设计中应注意的问题，在软件设计中重点介绍了节点初始化、报文发送和报文接收等子程序。 Abstract: The features of CAN Bus and the microcontroller P87C591 are introduced, and the design of hardware circuit and soft configuration of the signals collection node based on P87C591 are presented. The problems in designing hardware circuit are discussed.Initialization subprogram, transmiting subprogram and receiving subprogram are emphasized in soft configuration.
上传时间： 2013-11-03
上传用户：BIBI
PICkit™ 2 Microcontroller Programmer USER’S GUIDE This chapter contains general information that will be useful to know before using thePICkit™ 2 Microcontroller Programmer. Items discussed in this chapter include:• Document Layout• Conventions Used in this Guide• Warranty Registration• Recommended Reading• The Microchip Web Site• Development Systems Customer Change Notification Service• Customer Support• Document Revision History
标签： Microcontrolle PICkit 8482
上传时间： 2013-11-05
上传用户：妄想演绎师
The PCA9555 is a 24-pin CMOS device that provides 16 bits of General Purpose parallelInput/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed toenhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvementsinclude higher drive capability, 5 V I/O tolerance, lower supply current, individual I/Oconfiguration, and smaller packaging. I/O expanders provide a simple solution whenadditional I/O is needed for ACPI power switches, sensors, push buttons, LEDs, fans, etc.The PCA9555 consists of two 8-bit Configuration (Input or Output selection); Input, Outputand Polarity Inversion (active HIGH or active LOW operation) registers. The systemmaster can enable the I/Os as either inputs or outputs by writing to the I/O configurationbits. The data for each Input or Output is kept in the corresponding Input or Outputregister. The polarity of the read register can be inverted with the Polarity Inversionregister. All registers can be read by the system master. Although pin-to-pin and I2C-busaddress compatible with the PCF8575, software changes are required due to theenhancements, and are discussed in Application Note AN469.
上传时间： 2013-11-13
上传用户：fredguo
基于P87 C591的CAN总线系统智能节点设计Design of CAN System Intelligent Node Based on P87C591 给出了基于带CAN控制器的单片8位微控制器P87C591的智能节点的硬件电路及软件结构，详细介绍了设计中的难点及实现过程中应注意的问题。关键词:CAN总线;智能节点 Abstract:A h ardc ircuita nds oftw arec onfigurationo fth ei ntelligentnode based on a microcontroller with CAN controller P87C591 arepresented.E speciallyt hec ruxi nd esigninga ndt hep roblemst hatshould be paid attention in realizing are discussed in details.Keyw ords:C AN;in telligentn ode CA N 总线 是德国Bosch从20世纪80年代初为解决现代汽车中众多的控制与测试仪器之间的数据交换而开发的一种串行数据通信协议，它是一种多主总线，通信介质可以是双绞线、同轴电缆或光导纤维。由于CAN总线具有较强的纠错能力，支持差分收发，因而适合高噪声环境。并具有较远的传输距离，适用于许多领域的分布式测控系统。目前已在工业自动化、建筑物环境控制、医疗设备等许多领域得到广泛的应用。CAN已成为国际标准化组织IS011898标准。
上传时间： 2013-10-30
上传用户：xymbian
基于多点网络的水厂自动监控系统设计Design of MPI Based Automatic Monitoring and Control System in Water Works刘 美 俊(湖南工程学院，湘潭411101)摘要针对水厂工作水泵多、现场离控制站距离远的特点，提出了一种基于MPI多点网络的自动监控系统的设计方法，分析了系统的工作原理，介绍了系统中数据的采集与处理、主站与从站的通信原理以及系统软件的设计。由于这种系统的主、从站PLC之间采用MPI网络通信，具有运行可靠、性能价格比高的特点，所以适用于中小规模水厂的分布式监控场合。关键词多点网络主站从站监控系统Abstract Ina ccordancew ithth efe atuersof w aterw orks,i. e. ，manyp umpsin o perationa ndth ep umps， farfor mt hec ontrolst ation,th em ethodo fdesigninga na utomati(〕monitoringa ndc ontorlsy stemb asedo nM PIis p resented.Th eo perationalpr incipleo fth esy stemi san alyzed,th ed atac olection,data processing; communication between master station and slave station as wel as design and system software are discussed. Because MPI network communicationis used among master station, slave stations and PLC, the system is reliable and high cost-efective. It is， suitable for smal and mediumsized water works for distrbuted monitoring and control.Keywords MPI Masterst ation Slaves tation Monitoringa ndc ontorlsy stem 自来 水 厂 的自动控制系统一般分为两大部分，一对组态硬件要求较高，投资较大。相对而言，MPI网是水源地深水泵的工作控制，一是水厂区变频恒压供络速度可达187.5 M bps，通过一级中继器传输距离可水控制，两部分的实际距离通常都比较远。某厂水源达Ikm 。根据水厂的具体情况，确定以MPI方式组地有3台深井泵给水厂区的蓄水池供水。水厂区的成网络，主站PLC为S7-300系列的CPU3121FM，从任务是对水池的水进行消毒处理后，通过加压泵向管站为S7-200系列的CPU222。这样既满足了系统要路恒压供水。选用Siemens公司的S7系列可编程控求，又相对于Profibus网络节省了三分之一的成本，制器(PLC)和上位机组成实时数据采集和监控系统， 这种分布式监控系统具有较高的性能价格比。系统对深水泵进行远程控制，对供水泵采用变频器进行恒中PLC的物理层采用RS - 485接口，网络延伸选用压控制以保证整个水厂的电机设备安全、可靠地运带防雷保护的中继器，使系统的安全运行得到了保行。证。MPI网络的拓扑结构如图1所示。1 多点网络(NWI)监控系统的组成Sie me ns 公司S7系列PLC通常有MP」多点网络与Profibus现场总线网络两种组网方式。Profibus现场总线的应用目前较为普遍，通用性较好，它由Profibus一DP, Profibus一FMS, Profibus一PA组成。Profibus - DP型用于分散外设间的数据传输，传输速率为9.6kbps一12Mbps，主要用于现场控制器与分散1/0之间的通信，可满足交直流调速系统快速响应的时间要求，特别适合于加工自动化领域的应用;Profibus - FMS主要解决车间级通信问题，完成中等传输速度的循环或非循环数据交换任务，适用于纺织、楼宇自动化、可编程控制器、低压开关等;Profibus - PA型采用了OSI模型的物理层和数据链路层，适用于过程自动化的总线类型。
上传时间： 2013-10-09
上传用户：fac1003
针对运行中火车测速运用多普勒效应采用DSP 设计雷达测速系统并阐述了其基本设计思想与工作原理给出系统硬件软件设计结构和原理图改善了原有光电测速精度提高了系统工作稳定性和可靠性经实验证明DSP 采集板工作稳定测速效果好关键词DSP; 雷达测速; 多普勒效应 On Board DSP-Based Radar Speed Measurement System TANG Wei, SUN Zhi-fang, CHEN Quan (Dept.of computer Science,Yangtze University,Jingzhou 434023,China)Abstract: This paper presents a DSP-based train speed measurement by using Doppler radar. The structure of the system is introduced.The hardware and software are also discussed.Key words: DSP; rader speed measurement; doppler principle
上传时间： 2013-10-27
上传用户：003030
Abstract: This application note discusses the development and deployment of 3G cellular femtocell base stations. The technicalchallenges for last-mile residential connectivity and adding system capacity in dense urban environments are discussed, with 3Gfemtocell base stations as a cost-effective solution. Maxim's 3GPP TS25.104-compliant transceiver solution is presented along withcomplete radio reference designs such as RD2550. For more information on the RD2550, see reference design 5364, "FemtocellRadio Reference Designs Using the MAX2550–MAX2553 Transceivers."
标签： Base-Station Applications Single-Chip Transceiver
上传时间： 2013-11-07
上传用户：songrui
