This example program shows how to configure and use the A/D Converter of the following microcontroller: STMicroelectronics ST10F166 After configuring the A/D, the program reads the A/D result and outputs the converted value using the serial port. To run this program... Build the project (Project Menu, Build Target) Start the debugger (Debug Menu, Start/Stop Debug Session) View the Serial Window (View Menu, Serial Window #1) View the A/D converter peripheral (Peripheral Menu, A/D Converter) Run the program (Debug Menu, Go) A debug script (debug.ini) creates buttons that set different analog values in A/D channels. As the program runs, you will see the A/D input and output change. Other buttons create signals that generate sine wave or sawtooth patterns as analog inputs. µ Vision3 users may enable the built-in Logic Analyzer to view, measure and compare these input signals graphically.
标签： microcontroll Converter configure following
上传时间： 2014-12-01
上传用户：独孤求源
The project KEIL_IODemo shows how to use memory allocation routines (malloc) and char I/O (printf, scanf) via a serial interface with the Keil ARM toolchain. The I/O functions are adapted for the Analog Devices ADuC7000 series using the SERIAL.C module. The example also shows the efficiency of the Keil CA ARM Compiler run-time library which is tuned for single chip systems.
标签： KEIL_IODemo allocation routines project
上传时间： 2013-12-08
上传用户：ve3344
UART I/O and Memory Allocation Example for GNU The project GNU_IODemo shows how to use memory allocation routines (malloc) and char I/O (printf, scanf) via a serial interface with the GNU toolchain. The I/O functions are adapted for the Analog Devices ADuC7000 series using the SERIAL.C module. The example also shows the efficiency of the Keil CA ARM Compiler run-time library which is tuned for single chip systems.
标签： Allocation GNU_IODemo Example project
上传时间： 2015-05-04
上传用户：Amygdala
Basic Test Concepts DC Parameters AC Parameters Functional Parameters Device Characterization Test Program Development Analog Test Concepts Test Using DSP Techniques in Testing Noise Reduction Techniques in Testing
标签： Parameters Characterization Functional Concepts
上传时间： 2013-12-20
上传用户：libinxny
A system simulation environment in Matlab/Simulink of RFID is constructed in this paper. Special attention is emphasized on the analog/RF circuit.Negative effects are concerned in the system model,such as phase noise of the local oscillator,TX-RX coupling,reflection of the environment, AWGN noise,DC offset,I/Q mismatch,etc.Performance of the whole system can be evaluated by changing the coding method,parameters of building blocks,and operation distance.Finally,some simulation results are presented in this paper.
标签： environment constructed simulation Simulink
上传时间： 2014-01-09
上传用户：zhangliming420
ST7529液晶驱动 The ST7529 is a driver & controller LSI for 32 gray scale graphic dot-matrix liquid crystal display systems. It generates 255 Segment and 160 Common driver circuits. This chip is connected directly to a microprocessor, accepts Serial Peripheral Interface (SPI), 8-bit/16-bit parallel or IIC display data and stores in an on-chip display data RAM. It performs display data RAM read/write operation with no external operating clock to minimize power consumption. In addition, because it contains power supply circuits necessary to drive liquid crystal, it is possible to make a display system with the fewest components.
标签： 7529 controller dot-matrix graphic
上传时间： 2013-12-02
上传用户：奇奇奔奔
Easy-to-Use, Ultra-Tiny, Differential, 16-Bit Delta Sigma ADC With I2C Interface The LTC2453 is an ultra-tiny, fully differential, 16-bit, analog-to-digital converter. The LTC2453 uses a single 2.7V to 5.5V supply and communicates through an I2C interface. The ADC is available in an 8-pin, 3mm x 2mm DFN package. It includes an integrated oscillator that does not require any external components. It uses a delta-sigma modulator as a converter core and has no latency for multiplexed applications. The LTC2453 includes a proprietary input sampling scheme that reduces the average input sampling current several orders of magnitude lower than conventional delta-sigma converters. Additionally, due to its architecture, there is negligible current leakage between the input pins.
标签： Differential Easy-to-Use Ultra-Tiny Interface
上传时间： 2014-01-08
上传用户：凤临西北
CF VHDL The CF+ design was designed using the timing diagrams of the Compact Flash specification rev. 1.4, Analog Devices ADSP-218xN DSP Microcomputer specification, and the Intel StrataFlash Memory 28F320J3 specification.
标签： specification the designed diagrams
上传时间： 2013-12-27
上传用户：yyyyyyyyyy
在单片机应用系统中，常用到模拟输出，数模D/A转换器（Digital to Analog Converter）是一种能把数字量转换成模拟量的电子器件
上传时间： 2016-04-11
上传用户：talenthn
This demonstration models a flight control for the longitudinal motion of a Grumman Aerospace F-14 Tomcat. First order linear approximations of the aircraft and actuator behavior are connected to an analog flight control design that uses the pilot s stick pitch command as the set point for the aircraft s pitch attitude and uses aircraft pitch angle and pitch rate to determine commands. A simplified Dryden wind gust model is incorporated to perturb the system.
标签： demonstration longitudinal Aerospace Grumman
上传时间： 2016-05-17
上传用户：wang5829
