虫虫首页| 资源下载| 资源专辑| 精品软件
登录| 注册

a-d

  • 基于单片机和FPGA的多功能计数器的设计

    以89S52单片机和EP1C6Q240C8型FPGA为控制核心的多功能计数器,是由峰值检波、A/D转换、程控放大、比较整形、移相网络部分组成,可实现测量正弦信号的频率、周期和相位差的功能。多功能计数器采用等精度的测量方法,可实现频率为1Hz~10MHz、幅度为0.01~5Vrms的正弦信号的精确测频,以及频率为10Hz~100kHz、幅度为0.5~5Vrms的正弦信号精确测相。液晶显示器能够实时显示当前信号的频率、周期和相位差。该多功能计数器精度高,界面友好,实用性强。 Abstract:  A multi-function counter,which uses89S52MCU and EP1C6Q240C8FPGA as a control core,consists of peak detector,A/D conversion,program-controlled amplification,compared shaping and phase-shifting network part.The counter measures the frequency,period and phase of sinusoidal signal.With the equal precision method,the multi-function counter achieves the precise frequency measurement of the sinusoidal signal which its frequency is from1Hz to10MHz,its amplitude is from0.01Vrms to5Vrms,as well as the accurate phase measurement of the sinusoidal signal which its frequency is from10Hz to100kHz,its amplitude is from0.5Vrms to5Vrms.The LCD monitor real-time displays the frequency,period and phase difference of current signal.The multi-function counter features high precision,friendly interface,and strong practical.

    标签: FPGA 单片机 多功能 计数器

    上传时间: 2013-11-15

    上传用户:gy592333

  • 基于C8051F020单片机的多路压力测量仪

    介绍了一种基于C8051F020单片机的多路压力测量仪。该测量仪选用电阻应变式压力传感器采集压力信号,并经放大电路处理后送入C8051F020单片机,再由C8051F020单片机内部的A/D转换器将采集到的压力信号进行模数转化,然后分别对数据进行存储和显示。该测量仪能测量6路压力信号,并且各测量点都能单独检测和设置。由于采用了C8051F020单片机,简化了硬件电路,增强了抗干扰能力,使得测量仪具有测量精度高,冲击小等特点。 Abstract:  A measurement apparatus for multi-channel pressure based on single chip microcomputer is introduced.It can measure 6 channels signal of the pressure,and the pressure measure points can be detection and located individually.The pressure signal sampling is obtained by resistor stress-type pressure sensors,the digital signals of 6 channels are collected through amplifying and adjustment circuit of pressure signals and internal integrated A/D converter of MCU.Finally,and it realizes the function to store and display data separately.C8051F020 was used to made hardware circuit simple,and it also enhanced the anti-interference ability.It features high precision and little impact.

    标签: C8051F020 单片机 多路 压力

    上传时间: 2013-11-16

    上传用户:yare

  • HT46R23/HT46C23 8位A/D型OTP/Mask

    概述 HT46x23是8位高性能精简指令集单片机,专门为多输入/输出口的产品而设计的.特别适合应用于像洗衣机控制器和家用电器类产品.其HALT功能可降低功耗.

    标签: HT 46 23 Mask

    上传时间: 2013-11-23

    上传用户:392210346

  • HT46R47,HT46R22,HT46R23,HT46R2

    前言 自从盛群半导体公司成立以来,即致力于单片机产品的设计与开发。虽然盛群半导体提供给客户各式各样的半导体器件,但其中单片机仍是盛群的主要关键产品,未来盛群半导体仍将继续扩展单片机产品系列完整性与功能性。通过长期累积的单片机研发经验与技术,盛群半导体能为各式各样的应用范围开发出高性能且低价位的单片机芯片。许多连接到外部感应器的重要应用需要处理模拟信号,所有的这些应用,在它们可以被单片机处理之前需要通过一个A/D转换器做模数信号的转换。为了满足这些需求,盛群开发出A/D系列的单片机,除了拥有I/O系列的所有特性和功能外,还含有集成的多通道A/D转换器,它的解析度和通道个数可调。而PWM功能和I2C接口,则进一步增加了A/D系列单片机的功能和应用的可行性。

    标签: 46R HT 46 R47

    上传时间: 2013-12-05

    上传用户:waitingfy

  • MCS-51单片机的系统扩展技术--数/模转换接口

    在工作控制和智能化仪表中,通常由微型计算机进行实时控制及实时数据处理。计算机所加工的信息总是数字量,而被控制或测量对象的有关参量往往是连续变化的模拟量,如温度、速度、压力等等,与此对应的电信号是模拟电信号。计算机要处理这种信号,首先必须将模拟量转换成数字量,这一转换过程就是“模/数转换(A/D)”

    标签: MCS 51 单片机

    上传时间: 2013-10-24

    上传用户:tzl1975

  • 基于AVR单片机Mega16的电子时钟设计

    Mega16是一款采用先进RISC精简指令,内置A/D的8位单片机,可支持低电压联机 Flash和EEPROM 写入功能;同时还支持 Basic和C 等高级语言编程。用它设计电子时钟不仅成本低,硬件简单,而且很容易实现系统移植。介绍了如何利用AVR系列单片机Mega16及1602字符液晶来设计电子时钟的方法,同时给出了相应的电路原理及部分语言程序。 Abstract:  ?Mega16 is a high-performance, low power consumption, the use of advanced RISC concise instructions, built-in A/D 8-bit microcontrollers, the on-line support for low-voltage Flash, EEPROM write function. Except Mega16 also support the Basic, C, and other high-level language programming.The electronic clock which is deisgned by Mega16 is not only low-cost, simple hardware, but easy to achieve system migration.The design method of electrioic clock based on the AVR Mega16 and character LCD1602 is introduced in this paper,and the corresponding circuit electrionic and some language program are given.

    标签: Mega AVR 16 单片机

    上传时间: 2014-12-27

    上传用户:zl5712176

  • 基于C8051F340的数据采集器设计

    针对众多低成本数据采集需求,采用带有片上USB控制器和D/A转换器的混合信号微处理器C8051F340,设计了一款可通过USB接口和LabVIEW图形用户界面实现与PC机联机的数据采集器,同时借助系统的SD卡存储独立实现现场长时间采集数据。该数据采集器成本低,结构简单,体积小,已成功用于工业现场。 Abstract:  Aiming at the need of low cost data acquisition, a data acquisition device is designed based on C8051F340 which is a mixed-signal microcontroller and integrates USB controller and A/D controller on a chip.The data acquisition device which can combine with PC by USB interface and LabVIEW graphical user interface,can realize data acquisition. At the same time,it can be solely run a long time in virtue of SD card in field.The date aequisition device features low cost,simple structure and little sharp, and it has been used in industry field.

    标签: C8051F340 数据 集器设计

    上传时间: 2014-05-31

    上传用户:1109003457

  • ADS1110与AT89C51单片机系统的接口电路设计

    针对51单片机系统中常用的A/D转换器价格高、精度低的缺点,介绍TI公司的16 位的带有I2C串行接口的A/D转换器ADS1110的工作原理,给出ADS1110与AT89C51单片机系统的接口电路和软件设计。实践证明,ADS1110具有高性价比和实用性。 Abstract:  According to the disadvantages of high expense and low accuracy of the general A/D converter used in MCS51 microchip system,the principle and working process of a high accuracy 16-bit A/D conversion ADS1110 which has I2C bus and belongs to TI Company are proposed here as well as the interface of ADS1110 to AT89C51 and software list.It is proved to be high performance index and practicability.

    标签: 1110 ADS 89C C51

    上传时间: 2013-11-21

    上传用户:gyq

  • LS7266R1在电子式万能材料试验机中的应用

    针对材料试验机等设备中要求测量或控制材料拉伸或压缩的位移,一般采用光电轴角编码器检测位置信号,输出正交编码脉冲信号。若采用其他方法检测位置信号,必然导致电路设计复杂,可靠性降低。因此,提出一种基于LS7266R1的电子式万能材料试验机设计方案。给出了试验机中的控制器工作原理,LS7266R1与单片机的接口硬件设计,以及主程序软件流程图。巧妙地把力量传感器,位移传感器等机械运动状态的压力或拉力以及位置坐标,变成了电压信号和电脉冲数字信号,供A/D测量和LS7266R1计数,从而实现了独立完成材料试验控制或通过PC机串口命令完成材料试验控制。 Abstract:  Aiming at the requirement that the displacement of the tension and compression always be tested and controlled in the equipement such as material testing machine. The position signal was tested by photoelectric axial angle coder. Therefore, the paper proposes the design of electronic universal testing machine design based on LS7266R1. If the position signal detected by other methods, will inevitably lead to the circuit design complexity, reliability decreased. The work theory of the controller, the hardware interface design between LS7266R1 and single chip, and the flow chart of main program, are presented in this paper. The signal of the compression or tension power and displacement at working, which tested by power sensor and displacement sensor especially, is changed into electric voltage and electric pulse numerical signals. And these signals can be tested by A/D and counted by LS7266R1. Finally the test of the material properties can be controlled by itself, or controlled by the COM command of PC.

    标签: 7266R 7266 LS R1

    上传时间: 2013-11-02

    上传用户:yl1140vista

  • 基于STC12C5408AD的记忆示波器

    主要介绍构成记忆示波器的STC12C5408AD增强型单片机8通道10位模数转换功能的设置、应用和具体的汇编程序设计,以及PC机串行通讯和图形显示的高速汇编程序的设计要点,并列举实例说明其应用效果。 Abstract:  The configuration, applications and the designs for? compiling program of the memorial oscillograph of 10 bits A/D conversation are introduced. It’s bases on STC12C5408AD 8? channels? single-chip? computer? in? enhancement? mode. It also recommends the devising essentials of high speed compiling program for PC serial communication and graphics display, lists examples to explain its effects in using.

    标签: C5408 5408 STC 12C

    上传时间: 2013-10-10

    上传用户:adada