The NCV7356 is a physical layer device for a single wire data linkcapable of operating with various Carrier Sense Multiple Accesswith Collision Resolution (CSMA/CR) protocols such as the BoschController Area Network (CAN) version 2.0. This serial data linknetwork is intended for use in applications where high data rate is notrequired and a lower data rate can achieve cost reductions in both thephysical media components and in the microprocessor and/ordedicated logic devices which use the network.The network shall be able to operate in either the normal data ratemode or a high-speed data download mode for assembly line andservice data transfer operations. The high-speed mode is onlyintended to be operational when the bus is attached to an off-boardservice node. This node shall provide temporary bus electrical loadswhich facilitate higher speed operation. Such temporary loads shouldbe removed when not performing download operations.The bit rate for normal communications is typically 33 kbit/s, forhigh-speed transmissions like described above a typical bit rate of83 kbit/s is recommended. The NCV7356 features undervoltagelockout, timeout for faulty blocked input signals, output blankingtime in case of bus ringing and a very low sleep mode current.
上传时间： 2013-10-24
上传用户：s蓝莓汁
The LPC2292/2294 microcontrollers are based on a 16/32-bit ARM7TDMI-S CPU with real-time emulation and embedded trace support, together with 256 kB of embedded high-speed flash memory. A 128-bit wide memory interface and a unique accelerator architecture enable 32-bit code execution at the maximum clock rate. For critical code size applications, the alternative 16-bit Thumb mode reduces code by more than 30 pct with minimal performance penalty. With their 144-pin package, low power consumption, various 32-bit timers, 8-channel 10-bit ADC, 2/4 (LPC2294) advanced CAN channels, PWM channels and up to nine external interrupt pins these microcontrollers are particularly suitable for automotive and industrial control applications as well as medical systems and fault-tolerant maintenance buses. The number of available fast GPIOs ranges from 76 (with external memory) through 112 (single-chip). With a wide range of additional serial communications interfaces, they are also suited for communication gateways and protocol converters as well as many other general-purpose applications. Remark: Throughout the data sheet, the term LPC2292/2294 will apply to devices with and without the /00 or /01 suffix. The suffixes /00 and /01 will be used to differentiate from other devices only when necessary.
上传时间： 2014-12-30
上传用户：aysyzxzm
Multioutput monolithic regulators are easy to use and fi tinto spaces where multichip solutions cannot. Nevertheless,the popularity of multioutput regulators is temperedby a lack of options for input voltages above 30V andsupport of high output currents. The LT3692A fi lls thisgap with a dual monolithic regulator that operates frominputs up to 36V. It also includes a number of channeloptimization features that allow the LT3692A’s per-channelperformance to rival that of multichip solutions.
上传时间： 2014-01-03
上传用户：Huge_Brother
The RT9018A/B is a high performance positive voltage regulator designed for use in applications requining very low Input voltage and very low dropout voltage at up to 3A(peak).
上传时间： 2013-10-10
上传用户：geshaowei
This book contains information obtained from authentic and highly regarded sources. Reprinted material is quoted with permission, and sources are indicated. A wide variety of references are listed. Reasonable efforts have been made to publish reliable data and information, but the author and the publisher cannot assume responsibility for the validity of all materials or for the consequences of their use.
上传时间： 2014-12-31
上传用户：PresidentHuang
IBIS 模型在做类似板级SI 仿真得到广泛应用。在做仿真的初级阶段，经常对于ibis 模型的描述有些疑问，只知道把模型拿来转换为软件所支持的格式或者直接使用，而对于IBIS 模型里面的数据描述什么都不算很明白，因此下面的一些描述是整理出来的一点对于ibis 的基本理解。在此引用很多presention来描述ibis 内容（有的照抄过来，阿弥陀佛，不要说抄袭，只不过习惯信手拈来说明一些问题），仅此向如muranyi 等ibis 先驱者致敬。本文难免有些错误或者考虑不周，随时欢迎进行讨论并对其进行修改！IBIS 模型的一些基本概念IBIS 这个词是Input/Output buffer information specification 的缩写。本文是基于IBIS ver3.2 所撰写出来（www.eigroup.org/IBIS/可下载到各种版本spec）,ver4.2增加很多新特性，由于在目前设计中没用到不予以讨论。。。在业界经常会把spice 模型描述为transistor model 是因为它描述很多电路细节问题。而把ibis 模型描述为behavioral model 是因为它并不象spice 模型那样描述电路的构成，IBIS 模型描述的只不过是电路的一种外在表现，象个黑匣子一样，输入什么然后就得到输出结果，而不需要了解里面驱动或者接收的电路构成。因此有所谓的garbage in, garbage out，ibis 模型的仿真精度依赖于模型的准确度以及考虑的worse case，因此无论你的模型如何精确而考虑的worse case 不周全或者你考虑的worse case 如何周全而模型不精确，都是得不到较好的仿真精度。
上传时间： 2013-10-16
上传用户：zhouli
温湿度传感器 sht11 仿真程序 sbit out =P3^0; //加热口 //sbit input =P1^1;//检测口 //sbit speek =P2^0;//报警 sbit clo =P3^7;//时钟 sbit ST =P3^5;//开始 sbit EOC =P3^6;//成功信号 sbit gwei =P3^4;//个位 sbit swei =P3^3;//十位 sbit bwei =P3^2;//百位 sbit qwei =P3^1;//千位 sbit speak =P0^0;//报警音 sbit bjled =P0^1;//报警灯 sbit zcled =P0^2;//正常LED int count; uchar xianzhi;//取转换结果 uchar seth;//高时间 uchar setl;//低时间 uchar seth_mi;//高时间 uchar setl_mi;//低时间 bit hlbz;//高低标志 bit clbz; bit spbz; ///定时中断程序/// void t0 (void) interrupt 1 using 0 { TH0=(65536-200)/256;//5ms*200=1000ms=1s TL0=(65536-200)%256; clo=!clo;//产生时钟 if(count>5000) { if(hlbz) { if(seth_mi==0){seth_mi=seth;hlbz=0;out=0;} else seth_mi--; } if(!hlbz) { if(setl_mi==0){setl_mi=setl;hlbz=1;out=1;} else setl_mi--; } count=0; } else count++; } ///////////// ///////延时/////// delay(int i) { while(--i); } ///////显示处理/////// xianshi() { int abcd=0; int i; for (i=0;i<5;i++) { abcd=xianzhi; gwei=1; swei=1; bwei=1; qwei=1; P1=dispcode[abcd/1000]; qwei=0; delay(70); qwei=1; abcd=abcd%1000; P1=dispcode[abcd/100]; bwei=0; delay(70); bwei=1; abcd=abcd%100; P1=dispcode[abcd/10]; swei=0; delay(70); swei=1; abcd=abcd%10; P1=dispcode[abcd]; gwei=0; delay(70); gwei=1; } } doing() { if(xianzhi>100) {bjled=0;speak=1;zcled=1;} else {bjled=1;speak=0;zcled=0;} } void main(void) { seth=60;//h60秒 setl=90;//l90秒 seth_mi=60;//h60秒 setl_mi=90;//l90秒 TMOD=0X01;//定时0 16位工作模式 TH0=(65536-200)/256; TL0=(65536-200)%256; TR0=1; //开始计时 ET0=1; //开定时0中断 EA=1; //开全中断 while(1) { ST=0; _nop_(); ST=1; _nop_(); ST=0; // EOC=0; xianshi(); while(!EOC) { xianshi(); } xianzhi=P2; xianshi(); doing(); } }
上传时间： 2013-11-07
上传用户：我们的船长
超声波传感器适用于对大幅的平面进行静止测距。普通的超声波传感器测距范围大概是 2cm~450cm，分辨率3mm（淘宝卖家说的，笔者测试环境没那么好，个人实测比较稳定的 距离10cm~2m 左右，超过此距离就经常有偶然不准确的情况发生了，当然不排除笔者技术 问题。） 测试对象是淘宝上面最便宜的SRF-04 超声波传感器，有四个脚：5v 电源脚（Vcc），触发控制端（Trig），接收端（Echo），地端（GND） 附:SRF 系列超声波传感器参数比较 模块工作原理： 采用IO 触发测距，给至少10us 的高电平信号； 模块自动发送8个40KHz 的方波，自动检测是否有信号返回； 有信号返回，通过IO 输出一高电平，高电平持续的时间就是超声波从发射到返回的时间．测试距离=(高电平时间*声速(340m/s))/2; 电路连接方法 Arduino 程序例子： constintTrigPin = 2; constintEchoPin = 3; floatcm; voidsetup() { Serial.begin(9600); pinMode(TrigPin, OUTPUT); pinMode(EchoPin, INPUT); } voidloop() { digitalWrite(TrigPin, LOW); //低高低电平发一个短时间脉冲去TrigPin delayMicroseconds(2); digitalWrite(TrigPin, HIGH); delayMicroseconds(10); digitalWrite(TrigPin, LOW); cm = pulseIn(EchoPin, HIGH) / 58.0; //将回波时间换算成cm cm = (int(cm * 100.0)) / 100.0; //保留两位小数 Serial.print(cm); Serial.print("cm"); Serial.println(); delay(1000); }
上传时间： 2013-10-18
上传用户：星仔
Nios II软件构建工具入门 The Nios® II Software Build Tools (SBT) allows you to construct a wide variety of complex embedded software systems using a command-line interface. From this interface, you can execute Software Built Tools command utilities, and use scripts other tools) to combine the command utilities in many useful ways. This chapter introduces you to project creation with the SBT at the command line This chapter includes the following sections: ■ “Advantages of Command-Line Software Development” ■ “Outline of the Nios II SBT Command-Line Interface” ■ “Getting Started in the SBT Command Line” ■ “Software Build Tools Scripting Basics” on page 3–8
上传时间： 2013-11-15
上传用户：nanxia
protel 99se 使用技巧以及常见问题解决方法：里面有一些protel 99se 特别技巧，还有我们经常遇到的一些问题！如何使一条走线至两个不同位置零件的距离相同? 您可先在Design/Rule/High Speed/Matched Net Lengths的规则中来新增规则设定,最后再用Tools/EqualizeNet Lengths 来等长化即可。 Q02、在SCHLIB中造一零件其PIN的属性，如何决定是Passive, Input, I/O, Hi- Z,Power,…..？在HELP中能找到说明吗？市面有关 SIM？PLD？的书吗？或贵公司有讲义？ 你可在零件库自制零件时点选零件Pin脚,并在Electrical Type里,可以自行设定PIN的 属性,您可参考台科大的Protel sch 99se 里面有介绍关于SIM的内容。 Q03、请问各位业界前辈,如何能顺利读取pcad8.6版的线路图,烦请告知 Protel 99SE只能读取P-CAD 2000的ASCII档案格式,所以你必须先将P-CAD8.6版的格式转为P-CAD 2000的档案格式,才能让Protel读取。 Q04、请问我该如何标示线径大小的那个平方呢 你可以将格点大小设小,还有将字形大小缩小,再放置数字的平方位置即可。 Q05、请问我一次如何更改所有组件的字型 您可以点选其中一个组件字型,再用Global的方法就可以达成你的要求。
上传时间： 2015-01-01
上传用户：yxgi5
