The PL2303 USB to Serial adapter is your smart and convenient accessory forconnecting RS-232 serial devices to your USB-equipped Windows host computer. Itprovides a bridge connection with a standard DB 9-pin male serial port connector inone end and a standard Type-A USB plug connector on the other end. You simplyattach the serial device onto the serial port of the cable and plug the USB connectorinto your PC USB port. It allows a simple and easy way of adding serial connectionsto your PC without having to go thru inserting a serial card and traditional portconfiguration.This USB to Serial adapter is ideal for connecting modems, cellular phones, PDAs,digital cameras, card readers and other serial devices to your computer. It providesserial connections up to 1Mbps of data transfer rate. And since USB does not requireany IRQ resource, more devices can be attached to the system without the previoushassles of device and resource conflicts.Finally, the PL-2303 USB to Serial adapter is a fully USB Specification compliantdevice and Therefore supports advanced power management such as suspend andresume operations as well as remote wakeup. The PL-2303 USB Serial cable adapteris designed to work on all Windows operating systems.
上传时间： 2013-11-01
上传用户：ghostparker
The main objective of this book is to present all the relevant informationrequired for RF and micro-wave power amplifier design includingwell-known and novel theoretical approaches and practical design techniquesas well as to suggest optimum design approaches effectively combininganalytical calculations and computer-aided design. This bookcan also be very useful for lecturing to promote the analytical way ofthinking with practical verification by making a bridge between theoryand practice of RF and microwave engineering. As it often happens, anew result is the well-forgotten old one. Therefore, the demonstrationof not only new results based on new technologies or circuit schematicsis given, but some sufficiently old ideas or approaches are also introduced,that could be very useful in modern practice or could contributeto appearance of new ideas or schematic techniques.
标签： Amplifier Microwave Design Power
上传时间： 2013-12-22
上传用户：vodssv
When I started writing the first edition of RF Power Amplifiers for Wireless Communications,some time back in 1997, it seemed that I was roaming a largely uninhabitedlandscape. For reasons still not clear to me there were few, if any, otherbooks dedicated to the subject of RF power amplifiers. Right at the same time, however,hundreds of engineers were being assigned projects to design PAs for wirelesscommunications products. It was not, Therefore, especially difficult to be successfulwith a book that was fortuitously at the right place and the right time.
标签： Communications Amplifiers Wireless Edition
上传时间： 2013-11-12
上传用户：YYRR
PCB methodologies originated in the United States.Units of measurement are Therefore typically in Imperial units, not SI/metric units.
标签： 布局技术
上传时间： 2013-11-21
上传用户：Tracey
Calculation of the Differential Impedance of Tracks on FR4 substrates There is a discrepancy between calculated and measured values of impedance for differential transmission lineson FR4. This is especially noticeable in the case of surface microstrip configurations. The anomaly is shown tobe due to the nature of the substrate material. This needs to be considered as a layered structure of epoxy resinand glass fibre. Calculations, using Boundary Element field methods, show that the distribution of the electricfield within this layered structure determines the apparent dielectric constant and Therefore affects theimpedance. Thus FR4 cannot be considered to be uniform dielectric when calculating differential impedance.
上传时间： 2013-10-18
上传用户：masochism
This document provides practical, common guidelines for incorporating PCI Express interconnect layouts onto Printed Circuit Boards (PCB) ranging from 4-layer desktop baseboard designs to 10- layer or more server baseboard designs. Guidelines and constraints in this document are intended for use on both baseboard and add-in card PCB designs. This includes interconnects between PCI Express devices located on the same baseboard (chip-to-chip routing) and interconnects between a PCI Express device located “down” on the baseboard and a device located “up” on an add-in card attached through a connector. This document is intended to cover all major components of the physical interconnect including design guidelines for the PCB traces, vias and AC coupling capacitors, as well as add-in card edge-finger and connector considerations. The intent of the guidelines and examples is to help ensure that good high-speed signal design practices are used and that the timing/jitter and loss/attenuation budgets can also be met from end-to-end across the PCI Express interconnect. However, while general physical guidelines and suggestions are given, they may not necessarily guarantee adequate performance of the interconnect for all layouts and implementations. Therefore, designers should consider modeling and simulation of the interconnect in order to ensure compliance to all applicable specifications. The document is composed of two main sections. The first section provides an overview of general topology and interconnect guidelines. The second section concentrates on physical layout constraints where bulleted items at the beginning of a topic highlight important constraints, while the narrative that follows offers additional insight.
上传时间： 2014-01-24
上传用户：s363994250
This simple SDI Notepad-like application demonstrates how, taking advantage of the MFC support for Unicode, to Turkmenize labels of the specified menu items. Actually, Turkmen is not supported by Windows 2000, Therefore, to create such resources as menu so that strings in Turkmen could be displayed I had to invent an additional technique 这是一个与记事本类似的简单的SDI应用程序，演示了怎样使用MFC来支持 Unicode，对指定的菜单条目进行Turkmenize标签化。实际上，Windwos 2000并不支持Turknen,因此,创建了那些菜单资源以便那些字符串可以在Turknen中显示,为此我必须开发其它的技术。 来源: http://www.codeguru.com/advancedui/SDI_Note.html
标签： Notepad-like demonstrates application advantage
上传时间： 2013-11-26
上传用户：txfyddz
LPC2148 USB Audio Device Example This USB example project implements an USB Audio Device that connects via the USB interface to the PC. It may be used on the following devices: LPC2141 LPC2142 LPC2144 LPC2146 LPC2148 An USB Audio Device (HID) does not require any special USB driver, since the USB Audio support is already built into Windows 2000 and Windows XP. Therefore USB Audio devices can be directly connected to the computer. This example project is designed to work with Keil MCB2140 Evaluation Board. Refer to Running USBAudio for information on how to operate this example project.
标签： Device USB Audio implements
上传时间： 2015-04-16
上传用户：VRMMO
嵌入式文件系统ucfs.zip This project should serve as an "easy start" with /FS. All paths are relative to the project file. You should Therefore be able to copy the entire directory (including all subdirectories) to any location on your harddrive.
标签： relative project should paths
上传时间： 2015-04-28
上传用户：zhliu007
ABAQUS is a general purpose finite element analysis program which is widely used to analyses mechanical, structure and civil engineering problems. Abaqus has some special feature for analysing fracture mechanics problems, and Therefore it is a main tools for the FE-analysis in the Fracture Group at the Mechanical Engineering at Glasgow Universtity. The software which can transfer data from Abaqus into a Matlab readable environment has been developed as a part of a research program in Constraint Estimation in Fracture Mechanics. This research program was funded by a grant from the Defence Research Agency through Prof. J. Sumpter.
标签： analysis analyses general element
上传时间： 2015-05-13
上传用户：xfbs821
