PCB 被动组件的隐藏特性解析 传统上，EMC一直被视为「黑色魔术（black magic）」。其实，EMC是可以藉由数学公式来理解的。不过，纵使有数学分析方法可以利用，但那些数学方程式对实际的EMC电路设计而言，仍然太过复杂了。幸运的是，在大多数的实务工作中，工程师并不需要完全理解那些复杂的数学公式和存在于EMC规范中的学理依据，只要藉由简单的数学模型，就能够明白要如何达到EMC的要求。本文藉由简单的数学公式和电磁理论，来说明在印刷电路板（PCB）上被动组件（passivecomponent）的隐藏行为和特性，这些都是工程师想让所设计的电子产品通过EMC标准时，事先所必须具备的基本知识。导线和PCB走线导线（wire）、走线（trace）、固定架……等看似不起眼的组件，却经常成为射频能量的最佳发射器（亦即，EMI的来源）。每一种组件都具有电感，这包含硅芯片的焊线（bond wire）、以及电阻、电容、电感的接脚。每根导线或走线都包含有隐藏的寄生电容和电感。这些寄生性组件会影响导线的阻抗大小，而且对频率很敏感。依据LC 的值（决定自共振频率）和PCB走线的长度，在某组件和PCB走线之间，可以产生自共振（self-resonance），因此，形成一根有效率的辐射天线。在低频时，导线大致上只具有电阻的特性。但在高频时，导线就具有电感的特性。因为变成高频后，会造成阻抗大小的变化，进而改变导线或PCB 走线与接地之间的EMC 设计，这时必需使用接地面（ground plane）和接地网格（ground grid）。导线和PCB 走线的最主要差别只在于，导线是圆形的，走线是长方形的。导线或走线的阻抗包含电阻R和感抗XL = 2πfL，在高频时，此阻抗定义为Z = R + j XL j2πfL，没有容抗Xc = 1/2πfC存在。频率高于100 kHz以上时，感抗大于电阻，此时导线或走线不再是低电阻的连接线，而是电感。一般而言，在音频以上工作的导线或走线应该视为电感，不能再看成电阻，而且可以是射频天线。
上传时间： 2013-10-08
上传用户：时代将军
Abstract: There are differences between the operation of low-frequency AC transformers and electronic transformersthat supply current to MR16 lamps, and there are also differences in the current draw for MR16 halogen lamps andMR16 LED lamps. These contrasts typically prevent an MR16 LED lamp from operating with most electronictransformers. This article explains how a high-brightness (HB) LED driver optimized for MR16 lamps will allow LEDlamps to be compatible with most electronic transformers.A similar version of this article appeared on Display Plus, July 7, 2012 and in German in Elektronikpraxis, October 1,2012.
上传时间： 2013-10-13
上传用户：playboys0
Abstract: We don't expect manufacturers to produce clothes that in one size that fits everyone. In thesame way, one ESD component can't solve all issues—each application has different ESD requirements.Knowing that "one size fits all" cannot apply to power design, the power designer, or the engineering"super hero," must consider all the potential disruptions to a steady flow of power and thenvarious waysto mitigate them. This tutorial describes voltage- and current-limiting devices and risetime reducers tomanage the power. It also points to free and low-cost software tools to help design lowpass filters, checkcapacitor self-resonance, and simulate circuits.
上传时间： 2013-11-17
上传用户：zhouxuepeng1
Automobile electronic systems place high demands ontoday’s DC/DC converters. They must be able to preciselyregulate an output voltage in the face of wide temperatureand input voltage ranges—including load dump transientsin excess of 60V and cold crank voltage drops to 4V. Theconverter must also be able to minimize battery drain inalways-on systems by maintaining high effi ciency over abroad load current range. Similar demands are made bymany 48V nonisolated telecom applications, 40V FireWireperipherals and battery-powered applications with autoplug adaptors. The LT3437’s best in classperformancemeets all of these requirements in a small thermallyenhanced 3mm × 3mm DFN package.
上传时间： 2013-10-15
上传用户：stampede
Avalanche photo diode (APD) receiver modules arewidely used in fi ber optic communication systems. AnAPD module contains the APD and a signal conditioningamplifi er, but is not completely self contained. It stillrequires signifi cant support circuitry including a highvoltage, low noise power supply and a precision currentmonitor to indicate the signal strength. The challenge issqueezing this support circuitry into applications withlimited board space. The LT®3482 addresses this challengeby integrating a monolithic DC/DC step-up converter andan accurate current monitor. The LT3482 can supportup to a 90V APD bias voltage, and the current monitorprovides better than 10% accuracy over four decades ofdynamic range (250nA to 2.5mA).
上传时间： 2014-01-18
上传用户：wenyuoo
Photomultipliers (PMT), avalanche photodiodes (APD),ultrasonic transducers, capacitance microphones, radiationdetectors and similar devices require high voltage,low current bias. Additionally, the high voltage must bepristinely free of noise; well under a millivolt is a commonrequirement with a few hundred microvolts sometimesnecessary. Normally, switching regulator confi gurationscannot achieve this performance level without employingspecial techniques. One aid to achieving low noise is thatload currents rarely exceed 5mA. This freedom permitsoutput fi ltering methods that are usually impractical
上传时间： 2013-10-28
上传用户：lhw888
基于CC1110单片机公交报站系统主要由CC1110单片机最小系统和WT588D语音模块组成，提出了如何实现语音报站，通过无线通信SimpliciTI网络协议实现公交站台的自动播报和OLCD液晶显示公交运行的各类信息。结果表明，该公交报站系统报站准确率99%，价格比同类产品下降了300%以上，系统组成结构简单，提高了系统的抗干扰性和稳定性，也便于携带。 Abstract: The bus stop announcement system based on CC1110 MCU is composed of CC1110 MCU minimum system and WT588D voice module. How to achieve the voice announcing is put forward.The bus-stop will announce automatically and display on the OLCD by means of wireless communication SimpliciTI network protocol. As a result， the bus station stop announcement systems reported 99% accuracy rate， price of similar products declined by 300% or more， system of simple structure， improve the anti-jamming and stability of the power system， it is also portable.
上传时间： 2013-10-20
上传用户：baby25825
The CAT93C46 is a 1 kb Serial EEPROM memory device which isconfigured as either 64 registers of 16 bits (ORG pin at VCC) or 128registers of 8 bits (ORG pin at GND). Each register can be written (orread) serially by using the DI (or DO) pin. The CAT93C46 features aself−timed internal write with auto−clear. On−chip Power−On Resetcircuit protects the internal logic against powering up in the wrongstate.
上传时间： 2013-11-19
上传用户：ynzfm
Bootloader是微处理器上电时运行的第一段代码，它可以通过通信接口实现对微处理器内部应用程序的更新升级，为网络化嵌入式产品的应用程序升级带来极大的便利。由于目前没有统一嵌入式系统的Bootloader。基于NEC 78K0系列单片机自编程原理，设计出一个适用于78K0/Fx2系列单片机的Bootloader，并能够通过单片机串口在线升级应用程序。 Abstract: Bootloader is the first piece of code executed after microprocessor startup. It makes the embedded product’s firmware update conveniently through communication interface. However， no unified bootloader is available for all kinds of microprocessor products. Based on the principle of self-programming NEC 78K0s’ series， a useful Bootloader which is suitable for 78K0/Fx2s’ series MCU is designed，the design can update the application through serial ports.
标签： Bootloader MCU 自编程
上传时间： 2013-10-25
上传用户：fang2010
The CAT28LV64 is a low voltage, low power, CMOS Parallel EEPROM organized as 8K x 8−bits. It requires a simple interface for in−system programming. On−chip address and data latches, self−timed write cycle with auto−clear and VCC power up/down write protection eliminate additional timing and protection hardware. DATA Polling and Toggle status bit signal the start and end of the self−timed write cycle. Additionally, the CAT28LV64 features hardware and software write protection.
上传时间： 2013-11-15
上传用户：浩子GG
