This ink marks LTC’s eighth circuit collection publication.1We are continually surprised, to the point of near mystification, by these circuit amalgams seemingly limitlessappeal. Reader requests ascend rapidly upon publication,remaining high for years, even decades. All LTC circuitcollections, despite diverse content, share this popularity,although just why remains an open question. Why isit? Perhaps the form; compact, complete, succinct andinsular. Perhaps the freedom of selection without commitment,akin to window shopping.
上传时间： 2014-01-06
上传用户：ligi201200
The MAX9257/MAX9258 programmable serializer/deserializer (SerDes) devices transfer both video data and control signals over the same twisted-pair cable. However, control data can only be transmitted during the vertical blank time, which is indicated by the control-channel-enabled output (CCEN) signal. The electronic control unit (ECU) firmware designer needs to know how quickly to respond to the CCEN signal before it times out and how to calculate this duration. This application note describes how to calculate the duration of the CCEN for the MAX9257/MAX9258 SerDes chipset. The calculation is based on STO timeout, clock frequency, and UART bit timing. The CCEN duration is programmable and can be closed if not in use.
上传时间： 2014-01-24
上传用户：xingisme
针对科研实验中对拉压千斤顶加载过程控制的需要，采用ATmega128单片机控制步进电机进而实现对执行系统的电动泵站实行自动控制。对力和位移的数据采集与处理及用步进电机控制电动泵站手柄的技术细节作了重点描述。通过单片机的A/D变换器对AMP放大模块采集的电桥信号作量化处理，千斤顶的操控手柄位置依电动油泵阀门开启的方向和大小作若干定位，单片机根据力或位移传感器信号，实时控制步进电机驱动手柄旋转到相应操控位置。 Abstract: This article describes the use of ATmega128 AVR microcontroller series of DBS electric pumping stations and QF100/200 separate twoway hydraulic jack to automate the process of manipulating the work of the technical content. Articles on force and displacement data acquisition and processing， and stepper motor control electric pump with the handle of the key technical details were described. Through the MCU’s A / D converter module is collected on the AMP amplification quantify the signal bridge， jack handle position control valve opening according to the direction of electric pumps for a number of positioning and size of the microcontroller based on force or displacement sensor signals， real-time control stepper motor drive control handle rotate to the appropriate location.
上传时间： 2014-01-16
上传用户：hasan2015
基于幅移键控技术ASK（Amplitude-Shift Keying），以C8051F340单片机作为监测终端控制器，C8051F330D单片机作为探测节点控制器，采用半双工的通信方式，通过监控终端和探测节点的无线收发电路，实现数据的双向无线传输。收发电路采用直径为0.8 mm的漆包线自行绕制成圆形空心线圈天线，天线直径为（3.4±0.3）cm。试验表明，探测节点与监测终端的通信距离为24 cm，通过桥接方式，节点收发功率为102 mW时，节点间的通信距离可达20 cm。与传统无线收发模块相比，该无线收发电路在受体积、功耗、成本限制的场合有广阔的应用前景。 Abstract: Based on ASK technology and with the C8051F340 and C8051F330D MCU as the controller， using half-duplex communication mode， this paper achieves bi-directional data transfer. Transceiver circuit constituted by enameled wire which diameter is 0.8mm and wound into a diameter （3.4±0.3） cm circular hollow coil antenna. Tests show that the communication distance between detection and monitoring of the terminal is 24cm，the distance is up to 20cm between two nodes when using the manner of bridging and the node transceiver power is 102mW. Compared with the conventional wireless transceiver modules， the circuit has wide application prospect in small size， low cost and low power consumption and other characteristics.
上传时间： 2013-10-19
上传用户：xz85592677
在需要实时大量输入汉字的显示控制处理应用中，利用传统单片机实现显示控制的设计方法是较难实现的。带汉字字库的液晶模块的使用使得小容量ROM单片机的大量汉字信息输入与显示成为可能。提出了针对汉字字库编码的二级索引拼音输入检索方法,介绍了以ST7920作为控制器的带汉字字库的液晶显示模块的接口方法及汉字显示和控制原理，给出了通用计算机键盘在单片机中的串行接口，采用该技术可大大增强单片机的汉字输入功能。为小容量ROM单片机的大批量汉字信息处理提供了一种汉字输入解决方案。 Abstract: It is difficult to realize Chinese characters input method based on the embedded system by using the traditional design method of display control. It is possible to input and display Chinese characters based on the embedded system with the ROM of small content by using the LCD module with Chinese characters.Chinese characters input method of the quadric index recall in allusion to Chinese characters code is brought forward.The interface and the principle of Chinese characters display control based on the LCD module controlled with the ST7920 is introduced too.The serial interface of the computer keyboard in common use and the embedded system is given at the same time. It can enhance the embedded system function of Chinese characters input by using this technology, and provide a kind of Chinese characters input scheme for the embedded system with small capacity ROM.
上传时间： 2013-11-19
上传用户：jhksyghr
The PCA82C250 and PCA82C251 are advanced transceiver products for use in automotive and general industrialapplications with transfer rates up to 1 Mbit/s. They support the differential bus signal representation beingdescribed in the international standard for in-vehicle CAN high-speed applications (ISO 11898). Controller AreaNetwork (CAN) is a serial bus protocol being primarily intended for transmission of control related data between anumber of bus nodes.
上传时间： 2013-11-24
上传用户：Alick
The Philips family of Multiplexers and Switches consists of bi-directional translating switches controlled via the I2C or SMBus to fan out an upstream SCL/SDA pair to 2, 4 or 8 downstream channels of SCx/SDx pairs. The Multiplexers allow only one downstream channel to be selected at a time, while the Switches allow any individual downstream channel or combination of downstream channels to be selected, depending on the content of the programmable control register. Once one or several channels have been selected, the device acts as a wire, allowing the master on the upstream channel to send commands to devices on all the active downstream channels, and devices on the active downstream channels to communicate with each other and the master. External pull-up resistors are used to pull each individual channel up to the desired voltage level. Combined interrupt output and hardware reset input are device options that are featured.
上传时间： 2013-10-11
上传用户：dianxin61
The PL2303 USB to Serial adapter is your smart and convenient accessory forconnecting RS-232 serial devices to your USB-equipped Windows host computer. Itprovides a bridge connection with a standard DB 9-pin male serial port connector inone end and a standard Type-A USB plug connector on the other end. You simplyattach the serial device onto the serial port of the cable and plug the USB connectorinto your PC USB port. It allows a simple and easy way of adding serial connectionsto your PC without having to go thru inserting a serial card and traditional portconfiguration.This USB to Serial adapter is ideal for connecting modems, cellular phones, PDAs,digital cameras, card readers and other serial devices to your computer. It providesserial connections up to 1Mbps of data transfer rate. And since USB does not requireany IRQ resource, more devices can be attached to the system without the previoushassles of device and resource conflicts.Finally, the PL-2303 USB to Serial adapter is a fully USB Specification compliantdevice and therefore supports advanced power management such as suspend andresume operations as well as remote wakeup. The PL-2303 USB Serial cable adapteris designed to work on all Windows operating systems.
上传时间： 2013-11-01
上传用户：ghostparker
摘 要 瞬态仿真领域的许多工作需要获得可视化数据, 仿真电路不能将输出参数绘制成图形时研究工作将受到很大影响. 而权威电路仿真软件PSpice 在这个方面不尽如人意. 本文提出了一种有效的解决办法: 通过MATLAB 编程搭建一个PSpice 与MATLAB 的数据接口,使PSpice输出数据文件可以导入到MATLAB中绘制图形. 这令我们能够很方便地获得数据的规律以有效地分析仿真结果, 这项技术对于教学和工程实践都有比较实际的帮助.关键词: 瞬态仿真 仿真程序 PSpice MATLAB 可视化数据The Data Transfer from Pspice to MATLABWu hao Ning yuanzhong Liang yingAbstract Many works in the area of transient simulation has shown how a emulator such asPSpice can be interfaced to an control analysis package such as MATLAB to get viewdata. Thepaper describes how such interfaces can be made using the MATLAB programming. The platformas a typical platform will solve the problem that PSpice software sometimes can not draw the datato a picture. It can make us find the rule from numerous data very expediently, so we can analyzethe outcome of the simulation. And it also can be used in the field of education.Keywords Transient Simulation Emulator PSpice MATLAB Viewdata1 引言科学研究和工程应用常需要进行电路仿真 PSpice可进行直流 交流 瞬态等基本电路特性分析 也可进行蒙托卡诺 MC 统计分析 最坏情况 Wcase 分析 优化设计等复杂电路特性分析 它是国际上仿真电路的权威软件 而MATLAB的主要特点有 高效方便的矩阵和数组运算 编程效率高 结构化面向对象 方便的绘图功能 用户使用方便 工具箱功能强大 两者各有着重点 两种软件结合应用 对研究工作有很重要的意义香港理工大学Y. S. LEE 等人首先将PSpice和MATLAB结合 开发了电力电子电路优化用的CAD 程序MATSPICE[6] 将两者相结合的关键在于 如何用MATLAB 获取PSpice的仿真数据 对此参考文献 6 里没有详细叙述 本文着重说明用MATLAB 读取PSpice仿真数据的具体方法本论文利用MATLAB对PSpice仿真出的数据处理绘制出后者无法得到或是效果不好的仿真图形 下面就两者结合使用的例子 进行具体说明
上传时间： 2013-10-20
上传用户：wuchunzhong
Verilog_HDL的基本语法详解（夏宇闻版）:Verilog HDL是一种用于数字逻辑电路设计的语言。用Verilog HDL描述的电路设计就是该电路的Verilog HDL模型。Verilog HDL既是一种行为描述的语言也是一种结构描述的语言。这也就是说，既可以用电路的功能描述也可以用元器件和它们之间的连接来建立所设计电路的Verilog HDL模型。Verilog模型可以是实际电路的不同级别的抽象。这些抽象的级别和它们对应的模型类型共有以下五种： 系统级（system）：用高级语言结构实现设计模块的外部性能的模型。 算法级（algorithm）：用高级语言结构实现设计算法的模型。 RTL级（Register Transfer Level）：描述数据在寄存器之间流动和如何处理这些数据的模型。 门级（gate-level）：描述逻辑门以及逻辑门之间的连接的模型。 开关级（switch-level）：描述器件中三极管和储存节点以及它们之间连接的模型。 一个复杂电路系统的完整Verilog HDL模型是由若干个Verilog HDL模块构成的，每一个模块又可以由若干个子模块构成。其中有些模块需要综合成具体电路，而有些模块只是与用户所设计的模块交互的现存电路或激励信号源。利用Verilog HDL语言结构所提供的这种功能就可以构造一个模块间的清晰层次结构来描述极其复杂的大型设计，并对所作设计的逻辑电路进行严格的验证。 Verilog HDL行为描述语言作为一种结构化和过程性的语言，其语法结构非常适合于算法级和RTL级的模型设计。这种行为描述语言具有以下功能： · 可描述顺序执行或并行执行的程序结构。 · 用延迟表达式或事件表达式来明确地控制过程的启动时间。 · 通过命名的事件来触发其它过程里的激活行为或停止行为。 · 提供了条件、if-else、case、循环程序结构。 · 提供了可带参数且非零延续时间的任务（task）程序结构。 · 提供了可定义新的操作符的函数结构（function）。 · 提供了用于建立表达式的算术运算符、逻辑运算符、位运算符。 · Verilog HDL语言作为一种结构化的语言也非常适合于门级和开关级的模型设计。因其结构化的特点又使它具有以下功能： - 提供了完整的一套组合型原语（primitive）; - 提供了双向通路和电阻器件的原语; - 可建立MOS器件的电荷分享和电荷衰减动态模型。 Verilog HDL的构造性语句可以精确地建立信号的模型。这是因为在Verilog HDL中，提供了延迟和输出强度的原语来建立精确程度很高的信号模型。信号值可以有不同的的强度，可以通过设定宽范围的模糊值来降低不确定条件的影响。 Verilog HDL作为一种高级的硬件描述编程语言，有着类似C语言的风格。其中有许多语句如：if语句、case语句等和C语言中的对应语句十分相似。如果读者已经掌握C语言编程的基础，那么学习Verilog HDL并不困难，我们只要对Verilog HDL某些语句的特殊方面着重理解，并加强上机练习就能很好地掌握它，利用它的强大功能来设计复杂的数字逻辑电路。下面我们将对Verilog HDL中的基本语法逐一加以介绍。
标签： Verilog_HDL
上传时间： 2013-11-23
上传用户：青春给了作业95
