从系统硬件设计和软件构成上，介绍一种以AT89C52单片机为核心,通过无线遥控方法实现对预设电话自动拨号报警的智能呼救系统。系统提供了患者在紧急情况下无法使用电话报警时的一种报警手段。由用户预设的多组电话号码作为语音报警对象,预录可长达20 s的语音信号来说明患者所处地点及病情，并通知患者家人。 Abstract: This paper introduces a intelligent alarming system which is realized by wireless remote control system.This system chiefly consists of AT89C51 the system can processor.User can input several groups of telephone number regarded as alarming objects,The system can record some information 20 seconds to tell the site of the patient.And notice the rokonok of the patient.
上传时间： 2013-11-19
上传用户：wd450412225
为解决输油管道温度压力参数实时监测的问题，设计了以C8051F930单片机作为控制核心的超低功耗输油管道温度压力远程监测系统。现场仪表使用高精度电桥采集数据，通过433 MHz短距离无线通信网络与远程终端RTU进行通信，RTU通过GPRS网络与PC上位机进行远程数据传输，在上位机中实现数据存储和图形化界面显示，从而实现输油管道温度压力参数的实时监测和异常报警。经实验证明，该系统的12位数据采集精度满足设计要求，漏码率小于1%，正常工作时间超过5个月，能实时有效地监测输油管道的温度压力参数，节省大量人工成本，有效预防管道参数异常造成的经济损失和环境污染。 Abstract: In order to solve the problems on real-time monitoring of pipeline temperature and pressure parameters， the ultra-low power remote pipeline temperature and pressure monitoring system was designed by using the single chip processor C8051F930 as the control core. The high-precision electric bridge was used in field instruments for data collection， the 433MHz short-range wireless communication network was used to make communication between field instrument and RTU， the GPRS was used by the RTU to transmit data to the PC host computer， and the data was stored and displayed in the PC host computer， so the real-time monitoring and exception alerts of pipeline temperature and pressure parameters were achieved. The experiment proves that the system of which error rate is less than 1% over five months working with the 12-bit data acquisition accuracy can effectively monitor the pipeline temperature and pressure parameters in real time， it saves a lot of labor costs and effectively prevents environmental pollution and economic losses caused by abnormal channel parameters.
上传时间： 2013-11-07
上传用户：cuibaigao
第一章 序論……………………………………………………………6 1- 1 研究動機…………………………………………………………..7 1- 2 專題目標…………………………………………………………..8 1- 3 工作流程…………………………………………………………..9 1- 4 開發環境與設備…………………………………………………10 第二章 德州儀器OMAP 開發套件…………………………………10 2- 1 OMAP介紹………………………………………………………10 2-1.1 OMAP是什麼?…….………………………………….…10 2-1.2 DSP的優點……………………………………………....11 2- 2 OMAP Architecture介紹………………………………………...12 2-2-1 OMAP1510 硬體架構………………………………….…12 2-2.2 OMAP1510軟體架構……………………………………...12 2-2.3 DSP / BIOS Bridge簡述…………………………………...13 2- 3 TI Innovator套件 -- OMAP1510 ……………………………..14 2-2.1 General Purpose processor -- ARM925T………………...14 2-2.2 DSP processor -- TMS320C55x …………………………15 2-2.3 IDE Tool – CCS …………………………………………15 2-2.4 Peripheral ………………………………………………..16 第三章 在OMAP1510上建構Embedded Linux System…………….17 3- 1 嵌入式工具………………………………………………………17 3-1.1 嵌入式程式開發與一般程式開發之不同………….….17 3-1.2 Cross Compiling的GNU工具程式……………………18 3-1.3 建立ARM-Linux Cross-Compiling 工具程式………...19 3-1.4 Serial Communication Program………………………...20 3- 2 Porting kernel………………………………………………….…21 3-2.1 Setup CCS ………………………………………….…..21 3-2.2 編譯及上傳Loader…………………………………..…23 3-2.3 編譯及上傳Kernel…………………………………..…24 3- 3 建構Root File System………………………………………..…..26 3-3.1 Flash ROM……………………………………………...26 3-3.2 NFS mounting…………………………………………..27 3-3.3 支援NFS Mounting 的kernel…………………………..27 3-3.4 提供NFS Mounting Service……………………………29 3-3.5 DHCP Server……………………………………………31 3-3.6 Linux root 檔案系統……………………………….…..32 3- 4 啟動及測試Innovator音效裝置…………………………..…….33 3- 5 建構支援DSP processor的環境…………………………...……34 3-5.1 Solution -- DSP Gateway簡介……………………..…34 3-5.2 DSP Gateway運作架構…………………………..…..35 3- 6 架設DSP Gateway………………………………………….…36 3-6.1 重編kernel……………………………………………...36 3-6.2 DEVFS driver…………………………………….……..36 3-6.3 編譯DSP tool和API……………………………..…….37 3-6.4 測試……………………………………………….…….37 第四章 MP3 Player……………………………………………….…..38 4- 1 MP3 介紹………………………………………………….…….38 4- 2 MP3 壓縮原理……………………………………………….….39 4- 3 Linux MP3 player – splay………………………………….…….41 4.3-1 splay介紹…………………………………………….…..41 4.3-2 splay 編譯………………………………………….…….41 4.3-3 splay 的使用說明………………………………….……41 第五章 程式改寫………………………………………………...…...42 5-1 程式評估與改寫………………………………………………...…42 5-1.1 Inter-Processor Communication Scheme…………….....42 5-1.2 ARM part programming……………………………..…42 5-1.3 DSP part programming………………………………....42 5-2 程式碼………………………………………………………..……43 5-3 雙處理器程式開發注意事項…………………………………...…47 第六章 效能評估與討論……………………………………………48 6-1 速度……………………………………………………………...48 6-2 CPU負載………………………………………………………..49 6-3 討論……………………………………………………………...49 6-3.1分工處理的經濟效益………………………………...49 6-3.2音質v.s 浮點與定點運算………………………..…..49 6-3.3 DSP Gateway架構的限制………………………….…50 6-3.4減少IO溝通……………….………………………….50 6-3.5網路掛載File System的Delay…………………..……51 第七章 結論心得…
上传时间： 2013-10-14
上传用户：a471778
随着单片机功能集成化的发展，其应用领域也逐渐地由传统的控制，扩展为控制处理、数据处理以及数字信号处理（DSP，Digital Signal Processing）等领域。凌阳的16位单片机就是为适应这种发展而设计的。它的CPU内核采用凌阳最新推出的µ’nSP™（Microcontroller and Signal Processor）16位微处理器芯片（以下简称µ’nSP™）。围绕µ’nSP™所形成的16位µ’nSP™系列单片机（以下简称µ’nSP™家族）采用的是模块式集成结构，它以µ’nSP™内核为中心集成不同规模的ROM、RAM和功能丰富的各种外设接口部件。
上传时间： 2013-11-07
上传用户：wpwpwlxwlx
This document describes the system hardware implementation for the OMAP3530 processor and theTPS65930/20 companion power integrated circuit (IC). The document concentrates on the powerconnectivity for the processor and the companion power IC. The document also briefly explains someother specifics related to power, such as the boot modes and the power-up sequence.
上传时间： 2013-11-14
上传用户：yeling1919
FeaturesThe following standard features are provided.• Choice of RTOS scheduling policy1. Pre-emptive:Always runs the highest available task. Tasks of identical priorityshare CPU time (fully pre-emptive with round robin time slicing).2. Cooperative:Context switches only occur if a task blocks, or explicitly callstaskYIELD().• Co-routines (light weight tasks that utilise very little RAM).• Message queues• Semaphores [via macros]• Trace visualisation ability (requires more RAM)• Majority of source code common to all supported development tools• Wide range of ports and examples
上传时间： 2013-10-13
上传用户：13162218709
The PCA9519 is a 4-channel level translating I2C-bus/SMBus repeater that enables theprocessor low voltage 2-wire serial bus to interface with standard I2C-bus or SMBus I/O.While retaining all the operating modes and features of the I2C-bus system during thelevel shifts, it also permits extension of the I2C-bus by providing bidirectional buffering forboth the data (SDA) and the clock (SCL) lines, thus enabling the I2C-bus or SMBusmaximum capacitance of 400 pF on the higher voltage side. The SDA and SCL pins areover-voltage tolerant and are high-impedance when the PCA9519 is unpowered.
标签： 4channel transla level 9519
上传时间： 2013-11-19
上传用户：jisiwole
基于单DSP的VoIP模拟电话适配器研究与实现:提出和实现了一种新颖的基于单个通用数字信号处理器(DSP)的VoIP模拟电话适配器方案。DSP的I/O和存储资源非常有限，通常适于运算密集型应用，不适宜控制密集型应用[5]。该系统高效利用单DSP的I/O和片内外存储器资源，采用μC/OS-II嵌入式实时操作系统，支持SIP和TCP-UDP/IP协议，通过LAN或者宽带接入，使普通电话机成为Internet终端，实现IP电话。该系统软硬件结构紧凑高效，运行稳定，成本低，具有广阔的应用前景。关键词：模拟电话适配器；IP电话；数字信号处理器；μC/OS-II 【Abstract】This paper presents a VoIP ATA solution based on a single digital signal processor (DSP). DSPs are suitable for arithmetic-intensiveapplication and unsuitable for control-intensive application because of the limitation of I/O and memory resources. This solution is based on a 16-bitfixed-point DSP and μC/OS-II embedded real-time operating system. It makes good use of the limited resources, supports SIP and TCP-UDP/IPprotocol. It can connect the analog telephone to Internet and realize the VoIP application. This system has a great future for its high efficiency andlow cost.【Key words】Analog telephone adapter (ATA); Voice over Internet protocol (VoIP); Digital signal processor (DSP); μC/OS-II Research and Implementation of VoIPATA Based on Single DSP
上传时间： 2013-11-20
上传用户：Wwill
本章将介绍μ’nSP™系列单片机的应用领域，具体讲述SPCE061A单片机在通讯、语音领域里的应用，并详细给出了有关系统的电路原理图、程序流程图以及程序代码，供读者参考。 μ’nSP™家族产品具有电源电压范围和工作速率范围较宽、集成度高、性能价格比高以及功耗低等特点，故其有非常广泛的应用领域。μ’nSP™家族系列产品，涵盖了非常广泛的应用。包括：发音与语音识别的微控制器（SPCE系列）、通信来电辩识应用的微控制器（SPT660x系列）、以及通用型微控制器等等，主要体现在以下几个方面： 用于数字信号处理 用于开发研制便携式移动终端 用于开发嵌入式计算机应用系统 用于数字信号处理1． 数字滤波器 (Digital Filter)数字滤波器是一种计算处理或算法。借助于此，可以将输入的一种数字信号或序列变换为另一种序列输出。数字滤波器已被广泛地应用于数字语音、数字图像处理以及模式识别和频谱分析。数字信号处理器（DSP，Digital Signal Processor）的作用是通过一系列数字来表示信号及其信息，并借助数字计算方法变换和处理这些信号。为了构成DSP，必须有一种部件能够快速地完成两个数值的乘法运算并将乘积累加于寄存器。“快速”意味着乘和累加（MAC，Multiply & ACcumulate）较高的运算速度。若以16位数值进行乘和累加，其结果应为32位。显然，μ’nSP™的硬件结构与其指令系统的结合足以构成DSP应用的硬件MAC单元，因而很适用于一些DSP方面的应用。
上传时间： 2014-01-26
上传用户：qb1993225
In this document, the term Ô60xÕ is used to denote a 32-bit microprocessor from the PowerPC architecture family that conforms to the bus interface of the PowerPC 601ª, PowerPC 603ª, or PowerPC 604 microprocessors. Note that this does not include the PowerPC 602ª microprocessor which has a multiplexed address/data bus. 60x processors implement the PowerPC architecture as it is speciÞed for 32-bit addressing, which provides 32-bit effective (logical) addresses, integer data types of 8, 16, and 32 bits,and ßoating-point data types of 32 and 64 bits (single-precision and double-precision).1.1 Overview The MPC106 provides an integrated high-bandwidth, high-performance, TTL-compatible interface between a 60x processor, a secondary (L2) cache or additional (up to four total) 60x processors, the PCI bus,and main memory. This section provides a block diagram showing the major functional units of the 106 and describes brießy how those units interact.Figure 1 shows the major functional units within the 106. Note that this is a conceptual block diagram intended to show the basic features rather than an attempt to show how these features are physically implemented on the device.
上传时间： 2013-10-08
上传用户：18711024007
